Hi I have a Hauppage nova-td USB stick and I'm using Ubuntu Gutsy, Kernel 2.6.22-14. I cannot seem to discover any channels when scanning. When I use the nove-td USB stick on a Windows PC (same cable and connection to roof antenna), I can pick up and watch about 65 channels! I downloaded and compiled and installed the latest drivers as per the instructions on the wiki. It seems as though the stick is detected ok: Jan 13 21:58:32 247 kernel: [ 599.520000] dvb-usb: found a 'Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity' in cold state, will try to load a firmware Jan 13 21:58:32 247 kernel: [ 599.530000] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' Jan 13 21:58:33 247 kernel: [ 600.250000] dvb-usb: found a 'Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity' in warm state. Jan 13 21:58:33 247 kernel: [ 600.250000] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Jan 13 21:58:33 247 kernel: [ 600.250000] DVB: registering new adapter (Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity) Jan 13 21:58:33 247 kernel: [ 600.500000] DVB: registering frontend 0 (DiBcom 7000PC)... Jan 13 21:58:33 247 kernel: [ 600.730000] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. Jan 13 21:58:33 247 kernel: [ 600.730000] DVB: registering new adapter (Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity) Jan 13 21:58:33 247 kernel: [ 600.890000] DVB: registering frontend 1 (DiBcom 7000PC)... Jan 13 21:58:34 247 kernel: [ 601.060000] input: IR-receiver inside an USB DVB receiver as /class/input/input2 Jan 13 21:58:34 247 kernel: [ 601.060000] dvb-usb: schedule remote query interval to 150 msecs. Jan 13 21:58:34 247 kernel: [ 601.060000] dvb-usb: Hauppauge Nova-TD Stick/Elgato Eye-TV Diversity successfully initialized and connected. Jan 13 21:58:34 247 kernel: [ 601.060000] usbcore: registered new interface driver dvb_usb_dib0700 I set the built-in amplifier on: sgreszcz@247:~$ sudo cat /sys/module/dvb_usb_dib0700/parameters/force_lna_activation 1 When I scan however, I get nothing: sgreszcz@247:~$ sudo scan -5 /usr/share/doc/dvb-utils/examples/scan/dvb-t/uk-CrystalPalace > /home/sgreszcz/.tzap/channels.conf [sudo] password for sgreszcz: scanning /usr/share/doc/dvb-utils/examples/scan/dvb-t/uk-CrystalPalace using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 505833333 0 3 9 1 0 0 0 >>> tune to: 505833333:INVERSION_AUTO:BANDWIDTH_8_MHZ:FEC_3_4:FEC_AUTO:QAM_16:TRANSMISSION_MODE_2K:GUARD_INTERVAL_1_32:HIERARCHY_NONE WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 WARNING: filter timeout pid 0x0010 dumping lists (0 services) Done. I've also tried dvbsnoop: sgreszcz@247:~$ sudo dvbsnoop -s pidscan dvbsnoop V1.4.00 -- http://dvbsnoop.sourceforge.net/ --------------------------------------------------------- Transponder PID-Scan... --------------------------------------------------------- sgreszcz@247:~$ _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
