Mauro Carvalho Chehab wrote: >> About the dmesg, I didn't have time to store it. Basically, on the first >> compilation, I got two errors, since tuner-simple and tea5767 weren't >> selected on Kconfig. I've then selected the option to auto-include the >> required i2c drivers. Those two messages disappeared. >> >> The log stated that TEA5767 were detected. >> It also stated that tuner-simple is working on 0x61. there weren't any log >> messages from tea5767 driver. >> > > Ok, I went home for lunch, after all. Those are the logs: > > Linux video capture interface: v2.00 > cx88/0: cx2388x v4l2 driver version 0.0.6 loaded > ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 74 > cx88[0]: subsystem: 0000:0000, board: PixelView PlayTV Ultra Pro (Stereo) [card=27,insmod option] > cx88[0]: TV tuner type 59, Radio tuner type -1 > tveeprom 0-0050: Huh, no eeprom present (err=-121)? > input: cx88 IR (PixelView PlayTV Ultra as /class/input/input5 > cx88[0]/0: found at 0000:05:07.0, rev: 5, irq: 74, latency: 32, mmio: 0xc8000000 > TEA5767 detected. > tuner 0-0060: chip found @ 0xc0 (cx88[0]) > tuner 0-0060: Calling set_type_addr for type=59, addr=0xff, mode=0x04, config=0xffff8100 > tuner 0-0060: set addr for type 62 > tuner 0-0061: Setting mode_mask to 0x0c > tuner 0-0061: chip found @ 0xc2 (cx88[0]) > tuner 0-0061: Calling set_type_addr for type=59, addr=0xff, mode=0x04, config=0xffffffff > tuner 0-0061: set addr for type -1 > tuner 0-0061: defining GPIO callback > tuner 0-0061: tuner 0x61: called during i2c_client register by adapter's attach_inform > tuner 0-0061: defining GPIO callback > tuner-simple 0-0061: type set to 59 (Ymec TVision TVF-5533MF) > tuner 0-0061: type set to Ymec TVision TVF-5533MF > tuner 0-0061: cx88[0] tuner I2C addr 0xc2 with type 59 used for 0x0c > cx88[0]/0: registered device video0 [v4l2] > cx88[0]/0: registered device vbi0 > cx88[0]/0: registered device radio0 > tuner 0-0061: Cmd VIDIOC_S_STD accepted for analog TV > tuner 0-0061: switching to v4l2 > tuner 0-0061: tv freq set to 400.00 > > > (this time with a fresh copy - I got the same results as before) > Mauro, The output above looks correct. You say, "there weren't any log messages from tea5767 driver." -- This is because the tuner_info line was disabled -- I've re-enabled it just now, and push up the changeset. Please update your tree and test again -- I believe that the only issue here is the missing message from the tea5767 driver -- If you actually test radio, I believe that it will work. Please test again and get back to me. Regards, Mike _______________________________________________ linux-dvb mailing list linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
