Hi, all
hermann pitton schrieb:
> Hi,
>
> top posting is evil!
>
> But just realize, that it didn't reach the list(s).
>
> This doesn't sound bad!
>
> Hartmut, jump in if you have ideas. Obviously, I have to read the code
> myself again after seeing it only once at the mercurial web interface.
>
> I read this as tuner config changed to 3 all over the places and antenna
> input switching set to 0, but saa7134-dvb debug=1 is not enabled.
>
> I suggest we try next, if the heavy buzz on analog SECAM_L is gone.
> Offhand, gpio18 and gpio19 seem to be involved in switching for now.
>
> Next question might be, why DVB-T only works after using analog first.
>
> Cheers,
> Hermann
>
>
> Am Samstag, den 03.02.2007, 22:41 +0100 schrieb Emmanuel QUEMENER:
>> hermann pitton a écrit :
>>
>>> Am Samstag, den 03.02.2007, 02:55 +0100 schrieb hermann pitton:
>>>
>>>> Am Samstag, den 03.02.2007, 01:17 +0100 schrieb Emmanuel QUEMENER:
>>>>
>>>>> hermann pitton a écrit :
>>>>>
>>>>>
>>>>>> Am Freitag, den 02.02.2007, 20:43 +0100 schrieb Emmanuel QUEMENER:
>>>>>>
>>> [...]
>>>
>>>
>>>>> What do you purpose ?
>>>>>
>>>> There is also this 167000Hz positive frequency offset in France, but
>>>> your initial scan file seem to take it already into account.
>>>>
>>>> If possible try analog TV too. You change the LNA configuration for
>>>> analog in saa7134-cards.c for the test card=109 by setting
>>>> .tuner_config = 3.
>>>>
>>>> [SAA7134_BOARD_PHILIPS_TIGER_S] = {
>>>> .name = "Philips Tiger - S Reference design",
>>>> .audio_clock = 0x00187de7,
>>>> .tuner_type = TUNER_PHILIPS_TDA8290,
>>>> .radio_type = UNSET,
>>>> .tuner_addr = ADDR_UNSET,
>>>> .radio_addr = ADDR_UNSET,
>>>> .tuner_config = 2,
>>>> .mpeg = SAA7134_MPEG_DVB,
>>>> .gpiomask = 0x0200000,
>>>> .inputs = {{
>>>> .name = name_tv,
>>>> .vmux = 1,
>>>> .amux = TV,
>>>> .tv = 1,
>>>> },{
>>>>
>>>> For DVB-T you do this in saa7134-dvb.c here.
>>>>
>>>> static struct tda1004x_config philips_tiger_s_config = {
>>>> .demod_address = 0x08,
>>>> .invert = 1,
>>>> .invert_oclk = 0,
>>>> .xtal_freq = TDA10046_XTAL_16M,
>>>> .agc_config = TDA10046_AGC_TDA827X,
>>>> .gpio_config = TDA10046_GP01_I,
>>>> .if_freq = TDA10046_FREQ_045,
>>>> .i2c_gate = 0x4b,
>>>> .tuner_address = 0x61,
>>>> .tuner_config = 2,
>>>> .antenna_switch= 1,
>>>> .request_firmware = philips_tda1004x_request_firmware
>>>> };
>>>>
>>> Emmanuel,
>>>
>>> also in saa7134-cards.c in saa7134_board_init2 to stay consistent.
>>> On line 4397 after the eeprom detection.
>>>
>>> case SAA7134_BOARD_PHILIPS_TIGER:
>>> case SAA7134_BOARD_PHILIPS_TIGER_S:
>>>
>>> This configuration 3 is untested as announced by Hartmut.
>>> Let's see if it can make a difference for you.
>>>
>>> Hermann
>>>
>>>
>>>
>>>
>>>
>>>
>> Good evening,
>>
>> I've edited the files saa7134-cards.c saa7134-dvb.c saa7134-video and
>> change all references to video_config from 0 or 2 to 3.
>>
>> Here are the messages on load :
>>
>> saa7130/34: v4l2 driver version 0.2.14 loaded
>> saa7133[0]: found at 0000:03:0a.0, rev: 209, irq: 18, latency: 32, mmio:
>> 0xfdefe000
>> saa7133[0]: subsystem: 1043:4871, board: Philips Tiger - S Reference
>> design [card=109,insmod option]
>> saa7133[0]: board init: gpio is 600000
>> tuner 2-004b: chip at addr 4b is a tda8290
>> tuner 2-004b: Setting mode_mask to 0x0e
>> tuner 2-004b: chip found @ 0x96 (saa7133[0])
>> tuner 2-004b: Calling set_type_addr for type=54, addr=0xff, mode=0x04,
>> config=0x03
>> tuner 2-004b: set addr for type -1
>> tuner 2-004b: Defining GPIO function
>> tuner 2-004b: setting tuner address to 61
>> tuner 2-004b: type set to tda8290+75a
>> tuner 2-004b: saa7133[0] tuner I2C addr 0x96 with type 54 used for 0x0e
>> tuner 2-004b: Defining GPIO function
>> tuner 2-004b: setting tuner address to 61
>> tuner 2-004b: type set to tda8290+75a
>> tuner 2-004b: saa7133[0] tuner I2C addr 0x96 with type 54 used for 0x0e
>> saa7133[0]: i2c eeprom 00: 43 10 71 48 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
>> saa7133[0]: i2c eeprom 10: ff ff ff 0f ff 20 ff ff ff ff ff ff ff ff ff ff
>> saa7133[0]: i2c eeprom 20: 01 40 01 02 03 00 01 03 08 ff 00 cf ff ff ff ff
>> saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 22 15 50 ff ff ff ff ff ff
>> saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>> saa7133[0]: i2c scan: found device @ 0x10 [???]
>> saa7133[0]: i2c scan: found device @ 0x96 [???]
>> saa7133[0]: i2c scan: found device @ 0xa0 [eeprom]
>> tuner 2-004b: Calling set_type_addr for type=54, addr=0x4b, mode=0x0c,
>> config=0x03
>> tuner 2-004b: set addr for type 54
>> tuner 2-004b: Defining GPIO function
>> tuner 2-004b: setting tuner address to 61
>> tuner 2-004b: type set to tda8290+75a
>> tuner 2-004b: saa7133[0] tuner I2C addr 0x96 with type 54 used for 0x0e
>> tuner 2-004b: Cmd VIDIOC_S_STD accepted for analog TV
>> tuner 2-004b: switching to v4l2
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system B
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 128, ADC stat: 255, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 186, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 86
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system B
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 128, ADC stat: 255, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 186, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 86
>> saa7133[0]: registered device video0 [v4l2]
>> saa7133[0]: registered device vbi0
>> saa7133[0]: registered device radio0
>> saa7134 ALSA driver for DMA sound loaded
>> saa7133[0]/alsa: saa7133[0] at 0xfdefe000 irq 18 registered as card -1
>> DVB: registering new adapter (saa7133[0]).
>> DVB: registering frontend 0 (DVB-T Philips Tiger S)...
>> tda1004x: setting up plls for 48MHz sampling clock
>> tda1004x: found firmware revision 29 -- ok
>>
>> Initially, I was rather happy because the tzap seems to be more stable,
>> but the result is not stable enough in order to work fine when using
>> kaffeine :
>>
>> tuning to 498167000 Hz
>> video pid 0x0078, audio pid 0x0082
>> status 00 | signal ffff | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 1f | signal 9393 | snr a6a6 | ber 00012224 | unc ffffffff |
>> FE_HAS_LOCK
>> status 03 | signal ffff | snr a3a3 | ber 0001fffe | unc 00000000 |
>> status 00 | signal ffff | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 1f | signal 9b9b | snr 5c5c | ber 0000cff4 | unc ffffffff |
>> FE_HAS_LOCK
>> status 1f | signal eded | snr c0c0 | ber 00003446 | unc ffffffff |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr 6262 | ber 0001ce00 | unc ffffffff |
>> FE_HAS_LOCK
>> status 01 | signal dcdc | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 1f | signal ffff | snr 0000 | ber 0001fffe | unc ffffffff |
>> FE_HAS_LOCK
>> status 01 | signal ffff | snr 0000 | ber 0001fffe | unc ffffffff |
>> status 00 | signal 4e4e | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal ffff | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal ffff | snr 0808 | ber 0001fffe | unc 00000000 |
>> status 00 | signal dede | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal 8a8a | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal ffff | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal f2f2 | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 00 | signal 9797 | snr 3737 | ber 0001fffe | unc 00000000 |
>> status 1f | signal d0d0 | snr c9c9 | ber 0000489a | unc ffffffff |
>> FE_HAS_LOCK
>> status 1f | signal ffff | snr 5d5d | ber 0001d9fa | unc ffffffff |
>> FE_HAS_LOCK
>> status 00 | signal ffff | snr 0909 | ber 0001fffe | unc 00000000 |
>> status 1f | signal ffff | snr 3232 | ber 0001fffe | unc ffffffff |
>> FE_HAS_LOCK
>> status 05 | signal ffff | snr 6363 | ber 0001fffe | unc ffffffff |
>> status 00 | signal ffff | snr 0000 | ber 0001fffe | unc 00000000 |
>> status 1f | signal 9696 | snr abab | ber 0001d6f2 | unc ffffffff |
>> FE_HAS_LOCK
>>
>> I also tried to scan under scantv (scantv -C /dev/vbi0 -o
>> channels-analogic.txt)
>>
>> The result was possible to exploited by xdtv but I don't succeed to get
>> any sound (I investigate under mixer configuration but no change could
>> got me any sound !).
>>
>> Correction : wken analogic mode has been used, the digital mode works
>> fine !!!!!
>>
>> emmanuel@abu:~$ tzap -c channels.conf TF1
>> using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
>> tuning to 498167000 Hz
>> video pid 0x0078, audio pid 0x0082
>> status 00 | signal acac | snr 4848 | ber 0001fffe | unc 00000000 |
>> status 1f | signal acac | snr fefe | ber 00000248 | unc 00000046 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 0000022c | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 00000252 | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 00000220 | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 0000020c | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 0000023a | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal abab | snr ffff | ber 0000022c | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 00000248 | unc 00000000 |
>> FE_HAS_LOCK
>> status 1f | signal acac | snr fefe | ber 00000216 | unc 00000000 |
>> FE_HAS_LOCK
>>
>> Any idea ?
>>
>> Follow the logs of dmesg : all are about the tuner...
>>
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system B
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 1
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 0, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 30, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 255
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system B
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 0, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 100, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 0
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system B
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 0, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 255, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 194
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: insmod fixup: SECAM => SECAM-L
>> tuner 2-004b: tv freq set to 400.00
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 64, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 120, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 52
>> tuner 2-004b: trying to resolve SECAM L deadlock
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 479.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 241
>> tuner 2-004b: adjust gain, step 1. Agc: 241, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 246
>> tuner 2-004b: adjust gain, step 1. Agc: 246, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: adjust gain, step 2. Agc: 255, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 129
>> tuner 2-004b: trying to resolve SECAM L deadlock
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: Cmd TUNER_SET_STANDBY accepted for analog TV
>> tuner 2-004b: Cmd VIDIOC_S_STD accepted for analog TV
>> tuner 2-004b: insmod fixup: SECAM => SECAM-L
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 0, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 221, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 142
>> tuner 2-004b: trying to resolve SECAM L deadlock
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: insmod fixup: SECAM => SECAM-L
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 244
>> tuner 2-004b: adjust gain, step 1. Agc: 244, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: adjust gain, step 2. Agc: 255, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 105
>> tuner 2-004b: trying to resolve SECAM L deadlock
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: insmod fixup: SECAM => SECAM-L
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 244
>> tuner 2-004b: adjust gain, step 1. Agc: 244, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: insmod fixup: SECAM => SECAM-L
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: tda8290 not locked, no signal?
>> tuner 2-004b: adjust gain, step 1. Agc: 64, ADC stat: 0, lock: 0
>> tuner 2-004b: adjust gain, step 2. Agc: 191, lock: 0
>> tuner 2-004b: adjust gain, step 3. Agc: 58
>> tuner 2-004b: trying to resolve SECAM L deadlock
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 245
>> tuner 2-004b: adjust gain, step 1. Agc: 245, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 479.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 117
>> tuner 2-004b: adjust gain, step 1. Agc: 117, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 479.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 119
>> tuner 2-004b: adjust gain, step 1. Agc: 119, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 120
>> tuner 2-004b: adjust gain, step 1. Agc: 120, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tv freq set to 623.25
>> tuner 2-004b: setting tda8290 to system L
>> tuner 2-004b: tda827xa config is 0x03
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: setting LNA to high gain
>> tuner 2-004b: AGC2 gain is: 10
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: tda8290 is locked, AGC: 122
>> tuner 2-004b: adjust gain, step 1. Agc: 122, ADC stat: 0, lock: 128
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tuner 2-004b: Cmd TUNER_SET_STANDBY accepted for analog TV
>> saa7133[0]: dsp access error
>> saa7133[0]: dsp access error
>> tda1004x: setting up plls for 48MHz sampling clock
>> tda1004x: found firmware revision 29 -- ok
>> tda1004x: setting up plls for 48MHz sampling clock
>> tda1004x: found firmware revision 29 -- ok
>> tda1004x: setting up plls for 48MHz sampling clock
>> tda1004x: found firmware revision 29 -- ok
>>
>> Thanks for help.
>>
>> I will follow all the instructions in order to correct bugs or improve
>> drivers !!!
>>
>> Good night...
>>
>> EQ
>
>
I noticed 2 things:
> tuner 2-004b: AGC2 gain is: 10
This means maximum gain. With active LNA, i would expect lower
values...
second: The reason for the tumbling channel decoder might be a
not closed AGC loop.
But if DVB-T works after analog was on once with tuner_config 3,
this leads me to this:
Analog - digital mode switch might be GPIO22 like it is with some
ADS / Lifeview cards. Did you ever try card=87?
But this would cause trouble with the LNA since in the Philips
solutions, GPIO22 always is involved.
Are you sure the board has a LNA? In the philips designs, it sits
under the tuner shield and looks like a SMD voltage regulator.
If there is a LNA, the board seems to have a mode switch we haven't
seen yet. Except - did you try to invert tda1004x GPIO1, so
.gpio_config = TDA10046_GP00_I,
instead
.gpio_config = TDA10046_GP01_I,
Maybe this helps
Hartmut
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
