Hi,
Thanks for the suggestion I tried that, but it still doesn't make any
difference.
I forgot to mention last time, but if I wait a reasonable long period of
time 5 - 10 minutes I can then tune to QAM64 multiplex again.
Thanks
Adam
From: Nico Sabbi <nicola_sabbi@xxxxxxxxxxxxx>
To: linux-dvb <linux-dvb@xxxxxxxxxxx>
Subject: Re: Tuning problems with Lifeview FlyDVB-T LR301
Date: Fri, 01 Sep 2006 22:03:16 +0200
Adam Charrett wrote:
Hi,
I am having problems getting my FlyDVB-T to lock onto QAM64 signals. It
will occasionally lock onto the multiplex using tzap, but if I then quit
tzap and try again it won't lock, ever. I'm not having this problem with
QAM16 signals and it doesn't appear to be a problem under Windows (dual
boot machine), which makes me suspect the LinuxDVB drivers.
I am using version 7a0daff8ed2c.
The following is the dump of the kernel messages when the dvb driver is
loaded:
Linux video capture interface: v2.00
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:04:0a.0[A] -> Link [LNKC] -> GSI 18 (level, low)
-> IRQ 58
saa7134[0]: found at 0000:04:0a.0, rev: 1, irq: 58, latency: 32, mmio:
0xfeafdc00
saa7134[0]: subsystem: 5168:0301, board: LifeView FlyDVB-T / Genius
VideoWonder DVB-T [card=86,autodetected]
saa7134[0]: board init: gpio is 10000
input: saa7134 IR (LifeView FlyDVB-T / as /class/input/input9
saa7134[0]: i2c eeprom 00: 68 51 01 03 54 20 1c 00 43 43 a9 1c 55 d2 b2 92
saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 20: 01 40 01 02 03 ff 01 03 08 ff 01 08 ff ff ff ff
saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 40: ff 1b 00 c0 ff 10 01 01 ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7134[0]: registered device video0 [v4l2]
saa7134[0]: registered device vbi0
DVB: registering new adapter (saa7134[0]).
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
Any help would be much appreicated as I have 2 of these cards in 2
different machines and they both show this problem.
try to set all tuning parameters except frequency and bandwidth to AUTO
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
