|
I have done a mythdora install, with some problems
with the remote on the Compro DVB-T300. The card is not registering as an input
device, as it did with a previous install (earlier kernel, dvb module build from
cvs). Relevant parts of dmesg (from a cold boot) below. Two items of
interest:
input: device saa7134 IR (Compro Videomate DV is
statically allocated, will not register
Please convert to input_allocate_device() or contact dtor_core@xxxxxxxxxxxxx saa7134[0]: registered input device for IR and
tuner 2-0061: i2c i/o error: rc == -5 (should be
4)
I don't know if this "tuner 2..." line means
anything or not.
Has there been some change in the kernel that
saa7134 doesn't know about? Is there a possible build problem with
mythdora?
Cheers,
Mark
dmesg:
Linux version 2.6.15-1.1831_FC4 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxx)
(gcc version 4.0.2 20051125 (Red Hat 4.0.2-8)) #1 Tue Feb 7 13:37:42 EST
2006
snip
Linux video capture interface: v1.00
saa7130/34: v4l2 driver version 0.2.14 loaded saa7130/34: snapshot date 2005-11-09 ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 11 ACPI: PCI Interrupt 0000:02:09.0[A] -> Link [LNK2] -> GSI 11 (level, low) -> IRQ 11 saa7134[0]: found at 0000:02:09.0, rev: 1, irq: 11, latency: 32, mmio: 0xea000000 saa7134[0]: subsystem: 185b:c900, board: Compro Videomate DVB-T300 [card=70,insmod option] saa7134[0]: board init: gpio is 843f00 input: device saa7134 IR (Compro Videomate DV is statically allocated, will not register Please convert to input_allocate_device() or contact dtor_core@xxxxxxxxxxxxx saa7134[0]: registered input device for IR saa7134[0]: i2c eeprom 00: 5b 18 00 c9 54 20 1c 00 43 43 a9 1c 55 d2 b2 92 saa7134[0]: i2c eeprom 10: 00 ff 86 0f ff 20 ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 20: 01 40 01 03 03 ff 03 01 08 ff 00 87 ff ff ff ff saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 40: ff 02 00 c2 86 10 ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff cb saa7134[0]: i2c eeprom 60: 34 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff tuner 2-0061: chip found @ 0xc2 (saa7134[0]) tuner 2-0061: type set to 67 (Philips TD1316 Hybrid Tuner) tuner 2-0061: type set to 67 (Philips TD1316 Hybrid Tuner) tuner 2-0068: chip found @ 0xd0 (saa7134[0]) tda9887 2-0043: chip found @ 0x86 (saa7134[0]) saa7134[0]: registered device video0 [v4l2] saa7134[0]: registered device vbi0 DVB: registering new adapter (saa7134[0]). DVB: registering frontend 0 (Philips TDA10046H DVB-T)... snip
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision 23 -- ok tuner 2-0061: i2c i/o error: rc == -5 (should be 4) |
_______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
