Hi all, I'm the new kid on the block. A few days ago I have bought a KNC because it was stated that there is linux support for it out there. Unfortunately, I now know that this is not quite true. But with the 2.6.16-rc5 kernel (sourcemage 0.9.5) my computer recognizes the card: Mar 11 16:40:04 [kernel] Linux video capture interface: v1.00 Mar 11 16:40:04 [kernel] saa7146: register extension 'budget_av'. Mar 11 16:40:04 [kernel] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 Mar 11 16:40:04 [kernel] ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 Mar 11 16:40:04 [kernel] saa7146: found saa7146 @ mem f8860000 (revision 1, irq 11) (0x1894,0x0014). Mar 11 16:40:04 [kernel] DVB: registering new adapter (KNC TV STAR DVB-S). Mar 11 16:40:04 [kernel] adapter failed MAC signature check Mar 11 16:40:04 [kernel] encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff Mar 11 16:40:04 [kernel] budget-av: ci interface initialised. Mar 11 16:40:04 [kernel] KNC1-0: MAC addr = 00:09:d6:80:02:f2 Mar 11 16:40:04 [kernel] DVB: registering frontend 0 (ST STV0299 DVB-S)... That's as far as I get right now. These are the loaded modules: budget_av 14336 0 dvb_pll 9220 1 budget_av saa7146_vv 38528 1 budget_av video_buf 15620 2 saa7134,saa7146_vv v4l1_compat 11652 2 saa7134,saa7146_vv v4l2_common 6528 2 saa7134,saa7146_vv videodev 6784 3 saa7134,snd_tea575x_tuner,saa7146_vv budget_core 6660 1 budget_av saa7146 13064 3 budget_av,saa7146_vv,budget_core ttpci_eeprom 2176 1 budget_core stv0299 8968 1 budget_av dvb_core 66088 3 budget_av,budget_core,stv0299 tda10021 5380 1 budget_av tda1004x 11908 1 budget_av firmware_class 7296 2 budget_av,tda1004x i2c_core 17296 8 saa7134,ir_kbd_i2c,budget_av,budget_core,ttpci_eeprom,stv0299,tda10021,tda1004x but no userworld software is running yet. Kdetv does not find a device and klear says: and klear says: using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' status 00 | signal 0000 | snr 7116 | ber 0000ff10 | unc 00000000 | Demux: demux0 StreamReader thread started Reading in Content Reading sector loop status 00 | signal 0000 | snr 80a6 | ber 0000ff08 | unc 00000000 | status 00 | signal 0000 | snr 80d6 | ber 0000ff10 | unc 00000000 | status 00 | signal 0000 | snr 813f | ber 0000ff00 | unc 00000000 | status 00 | signal 0001 | snr 82ce | ber 0000ff08 | unc 00000000 | status 00 | signal 0001 | snr 8325 | ber 0000ff00 | unc 00000000 | status 00 | signal 0001 | snr 82ad | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 8298 | ber 00000000 | unc 00000000 | status 00 | signal 0000 | snr 8355 | ber 00001600 | unc 00000000 | status 00 | signal 0000 | snr 8334 | ber 0000ff08 | unc 00000000 | status 00 | signal 0000 | snr 831f | ber 0000ff38 | unc 00000000 | status 00 | signal 0000 | snr 8163 | ber 0000ff38 | unc 00000000 | status 00 | signal 0000 | snr 817e | ber 0000ff00 | unc 00000000 | status 00 | signal 0000 | snr 8280 | ber 0000ff10 | unc 00000000 | status 00 | signal 0002 | snr 82b6 | ber 0000ff00 | unc 00000000 | status 00 | signal 0000 | snr 8079 | ber 0000ff08 | unc 00000000 | status 00 | signal and so on, but no image appears. So *something* is working but I am not yet there. Anyone who can help me on? Cheers, and thanks a lot Edi _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
