On Sun, 2006-02-12 at 12:07 +0400, Manu Abraham wrote: > Jonek wrote: > > dvb_frontend_thread: using FE_ALGO_HW > > please do try dst_algo=0 as module parameter for dst. Ok, did that. It seems to me that tuning does not work properly now. And of course I get no picture either. > BTW: do you get a lock .. ? How do I see or check that? Do I get a lock while tuning and/or while reading TS packet from the device? Jonek while tuning, I get repeatedly ~ > czap VOX using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' 1 VOX:458000000:INVERSION_OFF:6900000:FEC_NONE:QAM_64:167:136 1 VOX: f 458000000, s 6900000, i 0, fec 0, qam 3, v 0xa7, a 0x88 status 00 | signal 0000 | snr 0000 | ber bfcba608 | unc bfcba684 | status 00 | signal 0000 | snr 0000 | ber bfcba608 | unc bfcba684 | status 00 | signal 0000 | snr 0000 | ber bfcba608 | unc bfcba684 | [...] dst(0) dst_set_freq: set Frequency 458000000 dst(0) dst_set_frontend: Set Frequency=[458000000] dst(0) dst_set_symbolrate: set symrate 6900000 dst(0) dst_set_symbolrate: DCT-CI dst(0) dst_write_tuna: type_flags 0x218 dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 06 fd 10 00 1a f4 40 9f ] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x06) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x06) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: RDC 8820 RESET dst(0) dst_error_bailout: Trying to bailout from previous error. dst(0) rdc_8820_reset: Resetting DST dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_write_tuna: write not successful [...] # modprobe dvb_bt8xx DVB: registering new adapter (bttv0). dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 1 dst(0) read_dst: reply is 0x0 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_get_device_id: Recognise [DCT-CI] dst(0) dst_type_print: DST type: cable DST type flags : 0x8 firmware version = 1 0x10 firmware version = 2 dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 0a 00 00 00 00 00 f6 ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait NOT ready after 200 dst(0) dst_get_mac: Unsupported Command dst(0) dst_probe: MAC: Unsupported command dst_ca_attach: registering DST-CA device DVB: registering frontend 0 (DST DVB-C)... _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
