On Sat, 2006-02-11 at 20:38 +0400, Manu Abraham wrote: > Jonek wrote: > > On Fri, 2006-02-10 at 09:58 +0400, Manu Abraham wrote: > >> Test with this tree, let's know how it looks for you. > >> http://www.thadathil.net/cgi-bin/hgwebdir.cgi/v4l-algo-test?cmd=archive;node=70266933831bc8efd85ecf808651595f79aede60;type=bz2 > > > > Tanks for your prompt answer. In the archive you pointed me to I made > > make and copied the following files over the ones in my current kernel's > > module dir: > > > > # cp bt878.ko dst.ko dst_ca.ko > > dvb-bt8xx.ko /lib/modules/2.6.15.3/kernel/drivers/media/dvb/bt8xx [...] > > ~ > Tuning to : VOX / autocount : 0 > > Using DVB card "DST DVB-C" > > tuning DVB-C to 458000000 > > inv:2 sr:6900000 fecH:0 mod:3 > > polling.... > > Getting frontend event > > > > Unable to handle kernel NULL pointer dereference at virtual address > > 00000000 > > printing eip: > > f93106a1 > > *pde = 00000000 > > Oops: 0002 [#2] > > PREEMPT SMP > > Modules linked in: dvb_bt8xx nxt6000 mt352 dvb_pll sp887x dst_ca > > dvb_core cx24110 or51211 lgdt330x dst bt878 tuner bttv video_buf > > v4l2_common btcx_risc tveeprom videodev nvidia bnep rfcomm l2cap nfsd > > exportfs lockd sunrpc nls_iso8859_15 ntfs dm_mod sd_mod usb_storage > > scsi_mod hci_usb bluetooth usbhid snd_emu10k1_synth snd_emux_synth > > snd_seq_virmidi snd_seq_midi_emul snd_seq_midi snd_seq_midi_event > > snd_seq snd_emu10k1 snd_intel8x0 snd_rawmidi snd_seq_device > > snd_ac97_codec snd_pcm_oss snd_mixer_oss em8300 snd_pcm adv717x > > snd_timer snd_ac97_bus snd_util_mem snd_hwdep snd ehci_hcd uhci_hcd > > sk98lin firmware_class i2c_i801 snd_page_alloc usbcore > > CPU: 0 > > EIP: 0060:[<f93106a1>] Tainted: P VLI > > EFLAGS: 00210246 (2.6.15.3) > > EIP is at dst_tune_frontend+0xf0/0xfc [dst] > > > You need to do a make, and a make install for the modules to work, you > copied only the immediate dependencies and hence the Oops. Ok, thank you for pointing that out. I thought I could copy only needed modules over to /lib/modules/[current kernel]. Or is that what make install does - to copy only what's needed? Sorry for all the typos and mistakes in my last mail :) I was in a hurry. So here we go again after a make install, anticipating that it did not work :(. # modprobe dst verbose=5 Linux video capture interface: v1.00 bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21 bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xf7efe000 bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:02:0d.1[A] -> GSI 21 (level, low) -> IRQ 21 bt878(0): Bt878 (rev 17) at 02:0d.1, irq: 21, latency: 64, memory: 0xf7eff000 # modprobe dvb_bt8xx DVB: registering new adapter (bttv0). dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 06 00 00 00 00 00 fa ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait ready after 0 dst(0) read_dst: reply is 0x0 0x44 0x43 0x54 0x2d 0x43 0x49 0x6c dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_get_device_id: Recognise [DCT-CI] dst(0) dst_type_print: DST type: cable DST type flags : 0x8 firmware version = 1 0x10 firmware version = 2 dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 00 0a 00 00 00 00 00 f6 ] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) read_dst: reply is 0xff dst(0) dst_wait_dst_ready: dst wait NOT ready after 200 dst(0) dst_get_mac: Unsupported Command dst(0) dst_probe: MAC: Unsupported command dst_ca_attach: registering DST-CA device DVB: registering frontend 0 (DST DVB-C)... ~ > czap ARD dvb_frontend_thread: using FE_ALGO_HW dst(0) dst_set_freq: set Frequency 410000000 dst(0) dst_tune_frontend: Set Frequency=[410000000] dst(0) dst_set_symbolrate: set symrate 6900000 dst(0) dst_set_symbolrate: DCT-CI dst(0) dst_write_tuna: type_flags 0x218 dst(0) dst_comm_init: Initializing DST. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) rdc_reset_state: Resetting state machine dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002] writing [ 06 41 90 00 1a f4 40 db ] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x06) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x06) dst(0) dst_error_recovery: Trying to return from previous errors. dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000] dst(0) write_dst: RDC 8820 RESET dst(0) dst_error_bailout: Trying to bailout from previous error. dst(0) rdc_8820_reset: Resetting DST dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0000] dst(0) dst_gpio_outb: mask=[0004], enbb=[0004], outhigh=[0004] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000] dst(0) dst_write_tuna: write not successful dvb_frontend_thread: using FE_ALGO_HW ~ > dvbstream -v 101 -a 102 -o > test.ts last message repeated 87 times There was NO data in test.ts :(. Now it's totaly broken :(. Is there something I can examine further to help you fixing this behaviour?? Could you please point out in short what the differences are between the version of the modules in the 2.6.15.3 kernel and the new ones you have given to me? I'm asking because it looks like a step back. I'm very grateful for your help!! Jonek _______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
