> Can you be a little more specific? I don't know what to tell you.
>
> VisionPlus DVB-T Digital TV Tuner Card
It will have a model number like VP-xxx
I see. VP-3020
>
> When it is working properly, it is auto detected by the kernel as card
> 113 (0x71).
>
No when it is , it will give you a message like
dst_get_device_id: xxxxxxxxxxxx
OK DTTDIG
DVB: registering new adapter (bttv0).
dst(0) dst_comm_init: Initializing DST. MP test.
dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000]
dst(0) rdc_reset_state: Resetting state machine
dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000]
dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002]
writing [ 00 06 00 00 00 00 00 fa ]
dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst(0) read_dst: reply is 0xff
dst(0) dst_wait_dst_ready: dst wait ready after 1
dst(0) read_dst: reply is 0x20
0x44 0x54 0x54 0x44 0x49 0x47 0x20
dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst(0) dst_get_device_id: Recognise [DTTDIG]
dst(0) dst_type_print: DST type: terrestrial
DST type flags : 0x10 firmware version = 2
dst(0) dst_comm_init: Initializing DST. MP test.
dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0001], outhigh=[0000]
dst(0) rdc_reset_state: Resetting state machine
dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0000]
dst(0) dst_gpio_outb: mask=[0002], enbb=[0002], outhigh=[0002]
writing [ 00 0a 00 00 00 00 00 f6 ]
dst(0) dst_gpio_outb: mask=[ffffffff], enbb=[0000], outhigh=[0000]
dst(0) read_dst: reply is 0xff
dst(0) dst_wait_dst_ready: dst wait ready after 0
dst(0) read_dst: reply is 0x0
0x8 0xca 0x10 0x13 0x24 0xe7 0x0
dst(0) dst_get_mac: MAC Address=[00:08:ca:13:24:00]
DVB: registering frontend 0 (DST DVB-T)...
please do send a lspci -vvv
When the card is working:
0000:02:0e.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB card
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 132 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f9000000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:02: 0e.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
Subsystem: Twinhan Technology Co. Ltd VisionPlus DVB Card
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 33 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f9001000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Thanks,
Matt
_______________________________________________ linux-dvb@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
