I have news concerning this problem : With budget-ci cards, if a CAM module is inserted, it is mandatory to create a transport connection with the CI for receiving data after tuning is ok. It was not necessary with older 2.4 drivers. That's why dvbscan failed receiving data whereas it is ok with VLC. Every software that does not communicate with CAM will not be able to receive data with this card (even not scrambled channel) if a CAM is inserted. Christophe Le Mardi 3 Janvier 2006 16:38, Christophe Burgalat a ?crit?: > Hi Mike, > > I did not test without the CAM module inserted. > And you're right, it works fine if I remove the CAM. > > But I confirm that It works perfectly using the dvb-kernel drivers for 2.4 > kernel with the CAM module. So I suppose there is a solution to this > problem. It seems also to concern other PCI card like the KNC1 > > Christophe > > Le Mardi 3 Janvier 2006 16:14, Michael Ditum a ?crit?: > > Hi Christophe, > > > > I'm having the same issue as you. I have posted a thread... > > http://www.linuxtv.org/pipermail/linux-dvb/2005-December/006906.html but > > have had no solution yet. > > > > The only thing I have worked out is that if I remove the CAM it works > > fine, I only get the filter timeout with the CAM inserted. > > > > Mike > > > > On 30/12/05, Christophe Burgalat <c.burgalat@xxxxxxxxxxxxxxxxxxx> wrote: > > > Hi, > > > > > > I have a WinTV-Nova-CI PCI card. > > > I use this card for some months and It works perfectly using kernel > > > 2.4and dvb drivers for 2.4 > > > > > > I try now to use 2.6 new kernel but I did not succeed to make it works. > > > I use dvbscan application and I have the following messages : > > > > > > "using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > > > WARNING: filter timeout pid 0x0011 > > > WARNING: filter timeout pid 0x0000 > > > dumping lists (0 services) > > > Done." > > > > > > It seems that tuning succeed but then nothing is received. > > > > > > I've tried to use 2.6.14.2 and 2.6.14.4 kernel (with udev), I also try > > > cvs dvb > > > drivers. > > > I use the latest dvb-ttpci firmware. > > > > > > Here is the output of the dmesg command : > > > > > > "saa7146: register extension 'dvb'. > > > saa7146: register extension 'budget_ci dvb'. > > > saa7146: found saa7146 @ mem ce868000 (revision 1, irq 5) > > > (0x13c2,0x100f). DVB: registering new adapter (TT-Budget/WinTV-NOVA-CI > > > PCI). > > > adapter has MAC addr = 00:d0:5c:23:c9:3f > > > budget_ci: CI interface initialised > > > dvb_ca adapter 0: DVB CAM detected and initialised successfully > > > DVB: registering frontend 0 (ST STV0299 DVB-S)... > > > " > > > > > > Output of the lsmod command: > > > > > > " > > > Module Size Used by > > > budget_ci 14016 0 > > > tda1004x 13668 1 budget_ci > > > budget_core 9796 1 budget_ci > > > dvb_ttpci 329188 0 > > > l64781 7268 1 dvb_ttpci > > > saa7146_vv 46144 1 dvb_ttpci > > > ves1820 5956 1 dvb_ttpci > > > tda8083 6084 1 dvb_ttpci > > > stv0297 7712 2 budget_ci,dvb_ttpci > > > sp8870 7468 1 dvb_ttpci > > > firmware_class 10112 4 budget_ci,tda1004x,dvb_ttpci,sp8870 > > > ves1x93 6692 1 dvb_ttpci > > > ttpci_eeprom 2880 2 budget_core,dvb_ttpci > > > saa7146 18088 4 > > > budget_ci,budget_core,dvb_ttpci,saa7146_vv stv0299 10856 > > > 2 budget_ci,dvb_ttpci > > > i2c_core 21152 12 > > > > > > budget_ci,tda1004x,budget_core,dvb_ttpci,l64781,ves1820,tda8083,stv0297 > > >,s p8870,ves1x93,ttpci_eeprom,stv0299 dvb_core 77384 3 > > > budget_ci,budget_core,dvb_ttpci > > > video_buf 21284 1 saa7146_vv > > > " > > > > > > > > > Any idea ?? > > > > > > Thanks > > > Christophe > > > > > > _______________________________________________ > > > > > > linux-dvb@xxxxxxxxxxx > > > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
