On Wednesday 28 December 2005 19:07, you wrote: With dst_algo I din't cheking becouse they load modue dst automaticly. # wget "http://83.110.18.182:8000/cgi-bin/hgwebdir.cgi/v4l-algo-test?cmd=archive;node=675755d11eb289dc063d4fc3fcc0e7503bbd5928;type=bz2"; # tar jxfv v4l-algo-test\?cmd\=archive\;node\=675755d11eb289dc063d4fc3fcc0e7503bbd5928\;type\=bz2 # cd cgi-bin-hgwebdir-cgi-v4l-algo-test-675755d11eb2/ make make install : Linux video capture interface: v1.00 : bttv: driver version 0.9.16 loaded : bttv: using 8 buffers with 2080k (520 pages) each for capture : bttv: Bt8xx card found (0). : ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 217 : bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 217, latency: 32, mmio: 0xd3000000 : bttv0: detected: Twinhan VisionPlus DVB [card=113], PCI subsystem ID is 1822:0001 : bttv0: using: Twinhan DST + clones [card=113,insmod option] : bttv0: gpio: en=00000000, out=00000000 in=00d500ff [init] : input.c: calling hotplug without a hotplug agent defined : ir-kbd-i2c: i2c IR (Hauppauge) detected at i2c-1/1-001a/ir0 [bt878 #0 [hw]] : bttv0: using tuner=4 : bttv0: add subdevice "dvb0" : bt878: AUDIO driver version 0.0.0 loaded : bt878: Bt878 AUDIO function found (0). : ACPI: PCI Interrupt 0000:00:0a.1[A] -> GSI 17 (level, low) -> IRQ 217 : bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 217, latency: 32, memory: 0xd3001000 : DVB: registering new adapter (bttv0). : dst_get_device_id: Recognise [DST-03T] : : DST type flags : 0x2 ts204 0x4 symdiv 0x10 firmware version = 2 : dst_get_mac: MAC Address=[00:08:ca:16:5e:00] : DVB: registering frontend 0 (DST DVB-S)... Now It's looks good. ./scan -l C-BAND Yamal201 scanning Yamal201 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' initial transponder 3645000 H 28000000 5 initial transponder 3645000 V 28000000 5 >>> tune to: 3645:h:0:28000 0x0000 0x000b: pmt_pid 0x0064 Gascom -- Kultura dubl-1 (running) 0x0000 0x000c: pmt_pid 0x00c8 Gascom -- Kultura dubl-2 (running) 0x0000 0x000d: pmt_pid 0x012c Gascom -- NTV (running) 0x0000 0x000e: pmt_pid 0x0190 Gascom -- TNT (running) 0x0000 0x000f: pmt_pid 0x01f4 Gascom -- DTV +7 (running) 0x0000 0x0010: pmt_pid 0x0258 Gascom -- TV3 (running) 0x0000 0x0011: pmt_pid 0x02bc Gascom -- Sport (running, scrambled) I'm typing to config xawtv but they say fontend not locked. kernel: dvb_frontend_thread: using FE_ALGO_HW last message repeated 46 times Thank.
