Hi, Martin
The fan starts as soon as the driver is initialized. Unfortunately, there
is no way to control it besides turning it on and off. But this is hard
coded and needs to be this way.
If you still have problems after updating the driver, please report. The
first step is to pose the kernel log generated by the driver.
Good luck
Hartmut
martin.fay@xxxxxxxx wrote:
> Hi Nico & Hartmut,
>
> thanks for your answer.
> i was trying it whit Card=55 & 60. 55 seems to be working. 60 is a no go one.
> I am going to try out Hartmut's step's and will proceed whit Results to the comunity.
>
> @Hartmut will the fan start to spinn after the card is correctly initzilized???
> could it be possible to control the RPM's of the fan by the Driver e.g. like +&- key
> just a wird idea ;-)
>
> tx&later
>
> Martin
>
>
>>and see what happens. So:
>>modprobe saa7134 card=55
>>modprobe saa7134-dvb
>
>
> ^^^^^^^^^^^^^^^^^^^^^^^^^^ Is this one requered for DVB-T ?
> after issuing this i did't see a msg at all in dmsg, ist this correct ?????
>
>
>>You don't need a firmware file, the card should have an eeprom and
>>boot from this.
>>You might consider to update the drivers from linuxtv.org first,
>>please get the v4l-kernel and dvb-kernel CVS and follow the
>>instructions in the wiki. I just added some updates.
>>
>>Good luck
>> Hartmut
>>
>>Nico Sabbi wrote:
>>
>>>Martin Fay wrote:
>>>
>>>
>>>>Hi Folks,
>>>>
>>>>first tx for all of yor great work!
>>>>
>>>>And now i have a problem
>>>>This card will not work in Suse or Ubuntu.
>>>>
>>>>Card:
>>>>Typhoon DVB-T Duo Digital/Analog 32bit Cardbus
>>>>
>>>>OS:
>>>>Ubuntu 5.10
>>>>
>>>>
>>>>
>>>>after i did a (root) modprobe saa7134-dvb here is the dmesg output:
>>>>
>>>>[4306459.391000] Linux video capture interface: v1.00
>>>>[4306459.438000] saa7130/34: v4l2 driver version 0.2.12 loaded
>>>>[4306459.447000] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] ->
>>>>GSI 11 (level, low) -> IRQ 11
>>>>[4306459.447000] saa7133[0]: quirk: PCIPCI_NATOMA
>>>>[4306459.447000] saa7133[0]: found at 0000:02:00.0, rev: 240, irq: 11,
>>>>latency: 64, mmio: 0x10800000
>>>>[4306459.447000] saa7133[0]: subsystem: 4e42:0502, board:
>>>>UNKNOWN/GENERIC [card=0,autodetected]
>>>>
>>>>
>>>
>>>^^^ try to force saa7134 with card= the number assigned to Lifeview DUO
>>>
>>>
>>>>[4306459.447000] saa7133[0]: board init: gpio is e010000
>>>>[4306459.448000] saa7133[0]: dsp access wait timeout [bit=WRR]
>>>>[4306459.448000] saa7133[0]: dsp access wait timeout [bit=WRR]
>>>>[4306459.561000] saa7133[0]: i2c eeprom 00: 42 4e 02 05 54 20 1c 00 43
>>>>43 a9 1c 55 d2 b2 92
>>>>[4306459.561000] saa7133[0]: i2c eeprom 10: 00 ff 22 0f ff 20 ff ff ff
>>>>ff ff ff ff ff ff ff
>>>>[4306459.561000] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08
>>>>ff 01 81 ff ff ff ff
>>>>[4306459.561000] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff
>>>>ff ff ff ff ff ff ff
>>>>[4306459.618000] saa7133[0]: registered device video0 [v4l2]
>>>>[4306459.660000] saa7133[0]: registered device vbi0
>>>>
>>>>looks like the driver is loadet but i cant access it also i am not so
>>>>shure if the firmware file (dvb-fe-tda10046.fw 24 kb ???)
>>>>is exactly the right one.
>>>>
>>>>Can please annyone of you help me here?
>>>>
>>
>>_______________________________________________
>>
>>linux-dvb@xxxxxxxxxxx
>>http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>>
>
>
> _______________________________________________
>
> linux-dvb@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>
