Hi Nico & Hartmut, thanks for your answer. i was trying it whit Card=55 & 60. 55 seems to be working. 60 is a no go one. I am going to try out Hartmut's step's and will proceed whit Results to the comunity. @Hartmut will the fan start to spinn after the card is correctly initzilized??? could it be possible to control the RPM's of the fan by the Driver e.g. like +&- key just a wird idea ;-) tx&later Martin > and see what happens. So: > modprobe saa7134 card=55 > modprobe saa7134-dvb ^^^^^^^^^^^^^^^^^^^^^^^^^^ Is this one requered for DVB-T ? after issuing this i did't see a msg at all in dmsg, ist this correct ????? > You don't need a firmware file, the card should have an eeprom and > boot from this. > You might consider to update the drivers from linuxtv.org first, > please get the v4l-kernel and dvb-kernel CVS and follow the > instructions in the wiki. I just added some updates. > > Good luck > Hartmut > > Nico Sabbi wrote: > > Martin Fay wrote: > > > >> Hi Folks, > >> > >> first tx for all of yor great work! > >> > >> And now i have a problem > >> This card will not work in Suse or Ubuntu. > >> > >> Card: > >> Typhoon DVB-T Duo Digital/Analog 32bit Cardbus > >> > >> OS: > >> Ubuntu 5.10 > >> > >> > >> > >> after i did a (root) modprobe saa7134-dvb here is the dmesg output: > >> > >> [4306459.391000] Linux video capture interface: v1.00 > >> [4306459.438000] saa7130/34: v4l2 driver version 0.2.12 loaded > >> [4306459.447000] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> > >> GSI 11 (level, low) -> IRQ 11 > >> [4306459.447000] saa7133[0]: quirk: PCIPCI_NATOMA > >> [4306459.447000] saa7133[0]: found at 0000:02:00.0, rev: 240, irq: 11, > >> latency: 64, mmio: 0x10800000 > >> [4306459.447000] saa7133[0]: subsystem: 4e42:0502, board: > >> UNKNOWN/GENERIC [card=0,autodetected] > >> > >> > > > > ^^^ try to force saa7134 with card= the number assigned to Lifeview DUO > > > >> [4306459.447000] saa7133[0]: board init: gpio is e010000 > >> [4306459.448000] saa7133[0]: dsp access wait timeout [bit=WRR] > >> [4306459.448000] saa7133[0]: dsp access wait timeout [bit=WRR] > >> [4306459.561000] saa7133[0]: i2c eeprom 00: 42 4e 02 05 54 20 1c 00 43 > >> 43 a9 1c 55 d2 b2 92 > >> [4306459.561000] saa7133[0]: i2c eeprom 10: 00 ff 22 0f ff 20 ff ff ff > >> ff ff ff ff ff ff ff > >> [4306459.561000] saa7133[0]: i2c eeprom 20: 01 40 01 03 03 01 01 03 08 > >> ff 01 81 ff ff ff ff > >> [4306459.561000] saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff > >> ff ff ff ff ff ff ff > >> [4306459.618000] saa7133[0]: registered device video0 [v4l2] > >> [4306459.660000] saa7133[0]: registered device vbi0 > >> > >> looks like the driver is loadet but i cant access it also i am not so > >> shure if the firmware file (dvb-fe-tda10046.fw 24 kb ???) > >> is exactly the right one. > >> > >> Can please annyone of you help me here? > >> > > _______________________________________________ > > linux-dvb@xxxxxxxxxxx > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb >
