Boleslaw Ciesielski wrote: > Mike Krufky wrote: > >>> Would be nice for someone who has that card to test it with the new >>> nxt200x driver. In it's current state, the flexcop patch proposed by >>> Kirk should do the trick. >>> >> Just to clarify, here is the patch that needs testing: >> >> Signed-off-by: Kirk Lapray <kirk.lapray@xxxxxxxxx> > > > With this patch and the Air2PC (nxt2002) I cannot get a lock on any > channels (it works with stock b2c2-flexcop-pci and also with the old > skystar2): > > $ azap WCVB > using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' > tuning to 509000000 Hz > video pid 0x0031, audio pid 0x0034 > status 00 | signal b770 | snr 5d8e | ber 00000000 | unc 00000000 | > status 00 | signal b780 | snr 5d5c | ber 00000000 | unc 00000000 | > status 00 | signal 7ad0 | snr 595a | ber 00000000 | unc 00000000 | > status 00 | signal dc00 | snr 7e3e | ber 00000000 | unc 00000000 | > > Attached is the kernel log. > > However, perhaps I don't know what I am doing in terms of working with > the v4l/dvb cvs trees. > > I started with vanilla 2.6.14 and then checked out v4l-kernel and > dvb-kernel from CVS. Then I applied the flexcop patch and did > > cd v4l-kernel > make merge-trees > make > make install The flexcop drivers live 100% in dvb-kernel cvs. You dont need v4l-kernel for them. > However this did not install any of the b2c2-flexcop* stuff (which is > what I was supposed to test after all). Not sure what to do I did > > cd ../dvb-kernel/build2.6 > make > make modules_install Hmmm... how about using the makelinks method, or using the insmod.sh script? This might work better. > but this installed into the /lib/modules/2.6.14/extra, so I had to > manually remove old modules from the kernel tree. > > Anyway, now lsmod shows this: > > b2c2_flexcop_pci 6488 0 > b2c2_flexcop 25036 1 b2c2_flexcop_pci > mt352 5956 1 b2c2_flexcop > bcm3510 10116 1 b2c2_flexcop > stv0299 9992 1 b2c2_flexcop > dvb_core 78056 2 b2c2_flexcop,stv0299 > nxt200x 14276 1 b2c2_flexcop > firmware_class 8064 3 b2c2_flexcop,bcm3510,nxt200x > dvb_pll 8644 2 b2c2_flexcop,nxt200x > stv0297_cs2 10884 1 b2c2_flexcop > lgdt330x 7452 1 b2c2_flexcop > mt312 7492 1 b2c2_flexcop > > and I don't think there are any old modules left so I think I got it > right. But is there an easier way to compile and test v4l/dvb outside of > kernel? > > Bolek > > > ------------------------------------------------------------------------ > > Oct 29 20:19:33 congo kernel: [ 62.332038] b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully > Oct 29 20:19:33 congo kernel: [ 62.359137] flexcop-pci: will use the HW PID filter. > Oct 29 20:19:33 congo kernel: [ 62.359153] flexcop-pci: card revision 2 > Oct 29 20:19:33 congo kernel: [ 62.359177] PCI: Found IRQ 9 for device 0000:00:0e.0 > Oct 29 20:19:33 congo kernel: [ 62.405024] DVB: registering new adapter (FlexCop Digital TV device). > Oct 29 20:19:33 congo kernel: [ 62.414399] b2c2-flexcop: MAC address = 00:d0:d7:02:54:25 > Oct 29 20:19:33 congo kernel: [ 62.417086] b2c2-flexcop: i2c master_xfer failed > Oct 29 20:19:33 congo kernel: [ 62.621098] b2c2-flexcop: i2c master_xfer failed > Oct 29 20:19:33 congo kernel: [ 62.621386] b2c2-flexcop: i2c master_xfer failed > Oct 29 20:19:33 congo kernel: [ 62.621394] mt352_read_register: readreg error (reg=127, ret==-121) > Oct 29 20:19:33 congo kernel: [ 62.621733] nxt200x: NXT2002 Detected > Oct 29 20:19:33 congo kernel: [ 62.621739] b2c2-flexcop: found the nxt2002 at i2c address: 0x0a > Oct 29 20:19:33 congo kernel: [ 62.621749] DVB: registering frontend 0 (Nextwave NXT200X VSB/QAM frontend)... > Oct 29 20:19:33 congo kernel: [ 62.624304] b2c2-flexcop: initialization of 'Air2PC/AirStar 2 ATSC 2nd generation' at the 'PCI' bus controlled by a 'FlexCopIIb' complete > [...] > Oct 29 20:20:20 congo kernel: [ 118.024828] nxt2002: Waiting for firmware upload (dvb-fe-nxt2002.fw)... > Oct 29 20:20:20 congo kernel: [ 118.199750] nxt2002: Waiting for firmware upload(2)... > Oct 29 20:20:21 congo kernel: [ 118.479020] nxt2002: Firmware upload complete > Oct 29 20:20:21 congo kernel: [ 118.795938] nxt200x: Timeout waiting for nxt200x to stop. This is ok after firmware upload. > Oct 29 20:20:38 congo hald[2698]: Timed out waiting for hotplug event 919. Rebasing to 947 Hmm.... any ideas, Kirk? -- Michael Krufky
