[linux-dvb] help with Twinhan VisionPlus 1020A

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi. Thanks for your quick reply, however, the problem is not solved yet.

I did a modprobe dvb_bt8xx, and the module loaded.
I didn't have the devices in /dev (maybe because I use udev?), I
created them manually.

However, the dvb-apps/utils/scan/dvbscan application (scan?) reports this:
--------------------
# util/scan/scan util/scan/dvb-s/Astra-19.2E
scanning util/scan/dvb-s/Astra-19.2E

using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0'
main:1882: FATAL: failed to open '/dev/dvb/adapter0/frontend0': 19 No
such device
--------------------
(frontend0 is c 212 3). On an italian forum is suggested that I should
load more modules, but I understand zero italian, so I couldn't
understand the message (other than a modprobe command).

I have loaded:
--------------------
# lsmod | grep dvb

dvb_bt8xx              10436  0
dvb_core               83848  1 dvb_bt8xx
nxt6000                 7524  1 dvb_bt8xx
mt352                   5764  1 dvb_bt8xx
dst                    13320  1 dvb_bt8xx
bt878                  11000  2 dvb_bt8xx,dst
sp887x                  8196  1 dvb_bt8xx
bttv                  155152  2 dvb_bt8xx,bt878
firmware_class         10144  3 dvb_bt8xx,sp887x,bttv
i2c_core               22736  10
mt312,dvb_bt8xx,nxt6000,mt352,dst,sp887x,tuner,bttv,i2c_algo_bit,i2c_i801
---------------------

I forgot to say it on my previous post, I'm using a 2.6.10-1-686
kernel from Debian Sarge (my last update was right before sarge was
frozen, but I cannot upgrade for a while).

Regards,
                   Luis.

On 7/24/05, Marc Dirix <marc@xxxxxxxxxxxxxxxxxxxxx> wrote:
> You should be able to see dvb nodes in your /dev even if the module
> isn't loaded. If you don't see them use
> 
> for most distro's :
> # cd /dev
> # ./MAKDEV dvb
> 
> This wil create an /dev/dvb directory with nodes inside for you.
> 
> If you don't have the /dev/MAKDEV either consult your distro how to do
> this, or do it by hand:
> 
> # cd /dev
> # mkdir -m 755 -p dvb/adapter0
> # cd dvb/adapter0
> The use mknod to make device nodes like this:
> 
> # mknod audio0 212 1
> 
> This is a list of the nodes:
> crw-rw----  1 root video 212, 1 Jul 24 14:14 audio0
> crw-rw----  1 root video 212, 6 Jul 24 14:14 ca0
> crw-rw----  1 root video 212, 4 Jul 24 14:14 demux0
> crw-rw----  1 root video 212, 5 Jul 24 14:14 dvr0
> crw-rw----  1 root video 212, 3 Jul 24 14:14 frontend0
> crw-rw----  1 root video 212, 7 Jul 24 14:14 net0
> crw-rw----  1 root video 212, 8 Jul 24 14:14 osd0
> crw-rw----  1 root video 212, 0 Jul 24 14:14 video0
> 
> 
> > For mplayer, you need to copy channels.conf from your ~/.szap dir to
> your ~/.mplayer dir.
> 
> 
> /Marc
> 
> On Sat, Jul 23, 2005 at 09:52:55PM -0400, Luis Alberto Zarrabeitia wrote:
> > Hello.
> > I recently purchased a Twinhan VP1020A card (DVB-S), and it is listed
> > as supported in the linuxtv site. However, I have not succeeded in
> > making it work.
> >
> > I saw some posts on this list very similar to what I am experiencing,
> > but unfortunately I did not understood the proposed solutions. I will
> > summarize what I know:
> >
> > ---- dmesg reports: --------
> > bttv: driver version 0.9.15 loaded
> > bttv: using 8 buffers with 2080k (520 pages) each for capture
> > bttv: Bt8xx card found (0).
> > ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 185
> > bttv0: Bt878 (rev 17) at 0000:02:02.0, irq: 185, latency: 32, mmio: 0xf47fe000
> > bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0
> > 001
> > bttv0: using: Twinhan DST + clones [card=113,autodetected]
> > bttv0: gpio: en=00000000, out=00000000 in=00f5ffff [init]
> > bttv0: using tuner=4
> > bttv0: add subdevice "dvb0"
> > ---------------------------------------
> > but I cannot find any device dvb0 under /dev. Following the
> > instructions at http://www.tldp.org/HOWTO/BTTV.html, I created a
> > /dev/video0 device, but xawtv wont work with it (v4l: open
> > /dev/video0: No such device). On this list it is explained that's
> > because it is a 'budget' card without a decoder. One of the replies
> > suggested the use of mplayer to test it, but I could not find a way to
> > do it (mplayer dvb:// reports 'DVB CONFIGURATION IS EMPTY, exit').
> >
> > Questions are, 1) how do I use it / test it? and 2) has anyone used it
> > with, for instance, MythTV?
> >
> > Regards,
> >                Luis Zarrabeitia.
> >
> > _______________________________________________
> > 
> > linux-dvb@xxxxxxxxxxx
> > http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
>



[Index of Archives]     [Linux Media]     [Video 4 Linux]     [Asterisk]     [Samba]     [Xorg]     [Xfree86]     [Linux USB]

  Powered by Linux