Hi, I finally got my hands on a DVB card, and have started what is becoming a very interesting proccess of getting it to work. Had to jump through a couple of hoops to get the dst module to recognize it as a DVB-T and not a DVB-S (the default KnoppMyth R5A16 install wouldn't budge on this issue). Since then I've tried kernels 2.6.10 , 2.6.11.11 and 2.6.12-rc5 with the CVS version of dvb-kernel, but with similar results. The card get's recognized as a DVB-T and the CI module is recognized, but when I try to get dvbscan to do it's thing, I get "tuning failed" and a bunch of error messages in dmesg. I've seen people have similar problems in the mailing list archives, but I was wondering if there is any progress in finding a solution. Regards, Einar dmesg output (using kernel 2.6.10 I get an error when I try to modprobe dvb-bt8xx. Had to remove snd_bt8xx and bt878 before modprobe'ing it again): ==================================================== bttv: driver version 0.9.15 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). bttv0: Bt878 (rev 17) at 0000:02:08.0, irq: 17, latency: 64, mmio: 0xfc001000 bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is 1822:0001 bttv0: using: Twinhan DST + clones [card=113,autodetected] bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init] bttv0: using tuner=4 bttv0: add subdevice "dvb0" bt878: AUDIO driver version 0.0.0 loaded dvb_bt8xx: unable to determine DMA core of card 0, dvb_bt8xx: if you have the ALSA bt87x audio driver installed, try removing it. dvb-bt8xx: probe of dvb0 failed with error -14 dvb_bt8xx: unable to determine DMA core of card 0, dvb_bt8xx: if you have the ALSA bt87x audio driver installed, try removing it. dvb-bt8xx: probe of dvb0 failed with error -14 bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). bt878(0): Bt878 (rev 17) at 02:08.1, irq: 17, latency: 64, memory: 0xfc000000 DVB: registering new adapter (bttv0). dst_get_device_id: Recognise [DTT-CI] DST type : terrestrial DST type flags : 0x2 ts204 0x10 firmware version = 2 DVB: registering frontend 0 (DST DVB-T)... . . . read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... dst_error_bailout: Trying to bailout from previous error... dst_write_tuna: read verify not successful. write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x0b) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... dst_error_bailout: Trying to bailout from previous error... dst_write_tuna: read verify not successful. write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x0b) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... dst_error_bailout: Trying to bailout from previous error... dst_write_tuna: read verify not successful. write_dst: _write_dst error (err == -5, len == 0x08, b0 == 0x0b) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... read_dst: read_dst error (err == -5, len == 0x01, b0 == 0xdc) dst_error_recovery: Trying to return from previous errors... dst_error_bailout: Trying to bailout from previous error... dst_write_tuna: read verify not successful. . . .