On 01/18/2015 08:29 PM, Lee Jones wrote: > On Thu, 15 Jan 2015, micky_ching@xxxxxxxxxxxxxx wrote: > >> From: Micky Ching <micky_ching@xxxxxxxxxxxxxx> >> >> update phy register value and using direct value instead of macros. >> It is much easier to debug using constant value than a lot of macros. >> We usually need compare the value directly to check the configure. > NACK. This is the opposite of what I would like to see. > When we debug, we usually need to compare the value provided from hardware, of course we can compare by print them to kernel log. but I think it more convenient from source code. And we only set phy register when initialize chip, so the value will not scattered everywhere, we will not benefit from macros. if we want to know the meaning of setting, we can look at the register define. >> Signed-off-by: Micky Ching <micky_ching@xxxxxxxxxxxxxx> >> --- >> drivers/mfd/rts5249.c | 46 ++++++++++++++-------------------------------- >> 1 file changed, 14 insertions(+), 32 deletions(-) >> >> diff --git a/drivers/mfd/rts5249.c b/drivers/mfd/rts5249.c >> index 2fe2854..00208d1 100644 >> --- a/drivers/mfd/rts5249.c >> +++ b/drivers/mfd/rts5249.c >> @@ -132,57 +132,39 @@ static int rts5249_optimize_phy(struct rtsx_pcr *pcr) >> if (err < 0) >> return err; >> >> - err = rtsx_pci_write_phy_register(pcr, PHY_REG_REV, >> - PHY_REG_REV_RESV | PHY_REG_REV_RXIDLE_LATCHED | >> - PHY_REG_REV_P1_EN | PHY_REG_REV_RXIDLE_EN | >> - PHY_REG_REV_RX_PWST | PHY_REG_REV_CLKREQ_DLY_TIMER_1_0 | >> - PHY_REG_REV_STOP_CLKRD | PHY_REG_REV_STOP_CLKWR); >> + err = rtsx_pci_write_phy_register(pcr, 0x19, 0xFE6C); >> if (err < 0) >> return err; >> >> msleep(1); >> >> - err = rtsx_pci_write_phy_register(pcr, PHY_BPCR, >> - PHY_BPCR_IBRXSEL | PHY_BPCR_IBTXSEL | >> - PHY_BPCR_IB_FILTER | PHY_BPCR_CMIRROR_EN); >> + err = rtsx_pci_write_phy_register(pcr, 0x0A, 0x05C0); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_PCR, >> - PHY_PCR_FORCE_CODE | PHY_PCR_OOBS_CALI_50 | >> - PHY_PCR_OOBS_VCM_08 | PHY_PCR_OOBS_SEN_90 | >> - PHY_PCR_RSSI_EN); >> + >> + err = rtsx_pci_write_phy_register(pcr, 0x00, 0xBA43); >> + if (err < 0) >> + return err; >> + err = rtsx_pci_write_phy_register(pcr, 0x03, 0xC152); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_RCR2, >> - PHY_RCR2_EMPHASE_EN | PHY_RCR2_NADJR | >> - PHY_RCR2_CDR_CP_10 | PHY_RCR2_CDR_SR_2 | >> - PHY_RCR2_FREQSEL_12 | PHY_RCR2_CPADJEN | >> - PHY_RCR2_CDR_SC_8 | PHY_RCR2_CALIB_LATE); >> + err = rtsx_pci_write_phy_register(pcr, 0x1E, 0x78EB); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_FLD4, >> - PHY_FLD4_FLDEN_SEL | PHY_FLD4_REQ_REF | >> - PHY_FLD4_RXAMP_OFF | PHY_FLD4_REQ_ADDA | >> - PHY_FLD4_BER_COUNT | PHY_FLD4_BER_TIMER | >> - PHY_FLD4_BER_CHK_EN); >> + err = rtsx_pci_write_phy_register(pcr, 0x05, 0x4600); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_RDR, PHY_RDR_RXDSEL_1_9); >> + err = rtsx_pci_write_phy_register(pcr, 0x02, 0x041F); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_RCR1, >> - PHY_RCR1_ADP_TIME | PHY_RCR1_VCO_COARSE); >> + err = rtsx_pci_write_phy_register(pcr, 0x1D, 0x0824); >> if (err < 0) >> return err; >> - err = rtsx_pci_write_phy_register(pcr, PHY_FLD3, >> - PHY_FLD3_TIMER_4 | PHY_FLD3_TIMER_6 | >> - PHY_FLD3_RXDELINK); >> + err = rtsx_pci_write_phy_register(pcr, 0x08, 0x4FE4); >> if (err < 0) >> return err; >> - return rtsx_pci_write_phy_register(pcr, PHY_TUNE, >> - PHY_TUNE_TUNEREF_1_0 | PHY_TUNE_VBGSEL_1252 | >> - PHY_TUNE_SDBUS_33 | PHY_TUNE_TUNED18 | >> - PHY_TUNE_TUNED12); >> + >> + return 0; >> } >> >> static int rts5249_turn_on_led(struct rtsx_pcr *pcr) _______________________________________________ devel mailing list devel@xxxxxxxxxxxxxxxxxxxxxx http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
