Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.
The ADV7180 power pin is via max7310_b port expander.
Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
- Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
- For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
---
arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 50 ++++++++++++++++++++++++++++++++
1 file changed, 50 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 1212f82..c24af28 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -124,6 +124,21 @@
#size-cells = <0>;
reg = <1>;
+ adv7180: camera@21 {
+ compatible = "adi,adv7180";
+ reg = <0x21>;
+ powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+
+ port {
+ adv7180_to_ipu1_csi0_mux: endpoint {
+ remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+ bus-width = <8>;
+ };
+ };
+ };
+
max7310_a: gpio@30 {
compatible = "maxim,max7310";
reg = <0x30>;
@@ -151,6 +166,25 @@
};
};
+&ipu1_csi0_from_ipu1_csi0_mux {
+ bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+ remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+ bus-width = <8>;
+};
+
+&ipu1_csi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu1_csi0>;
+
+ /* enable frame interval monitor on this port */
+ fim {
+ status = "okay";
+ };
+};
+
&clks {
assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
<&clks IMX6QDL_PLL4_BYPASS>,
@@ -444,6 +478,22 @@
>;
};
+ pinctrl_ipu1_csi0: ipu1csi0grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
+ MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+ MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x1b0b0
+ MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x1b0b0
+ >;
+ };
+
pinctrl_max7310: max7310grp {
fsl,pins = <
MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
--
2.7.4
_______________________________________________
devel mailing list
devel@xxxxxxxxxxxxxxxxxxxxxx
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
