On 03/11/2014 04:50 PM, Sören Brinkmann wrote: > On Tue, 2014-03-11 at 09:32AM +0100, Michal Simek wrote: >> On 03/10/2014 11:32 PM, Sören Brinkmann wrote: >>> On Mon, 2014-03-10 at 12:58PM +0100, Michal Simek wrote: >>>> On 03/10/2014 11:56 AM, Mark Rutland wrote: >>>>> On Sun, Mar 09, 2014 at 02:57:16AM +0000, Punnaiah Choudary Kalluri wrote: >>>>>> Added EDAC support for reporting the ecc errors of zynq ddr controller. >>>>>> The ddr ecc controller corrects single bit errors and detects double bit >>>>>> errors >>>>>> >>>>>> Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xxxxxxxxxx> >>>>>> --- >>>>>> .../devicetree/bindings/edac/zynq_edac.txt | 18 + >>>>>> drivers/edac/Kconfig | 7 + >>>>>> drivers/edac/Makefile | 1 + >>>>>> drivers/edac/zynq_edac.c | 613 ++++++++++++++++++++ >>>>>> 4 files changed, 639 insertions(+), 0 deletions(-) >>>>>> create mode 100644 Documentation/devicetree/bindings/edac/zynq_edac.txt >>>>>> create mode 100644 drivers/edac/zynq_edac.c >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/edac/zynq_edac.txt b/Documentation/devicetree/bindings/edac/zynq_edac.txt >>>>>> new file mode 100644 >>>>>> index 0000000..c21ff83 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/edac/zynq_edac.txt >>>>>> @@ -0,0 +1,18 @@ >>>>>> +Zynq EDAC driver, it does reports the DDR ECC single bit errors that are >>>>>> +corrected and double bit ecc errors that are detected by the DDR ECC controller. >>>>>> +ECC support for DDR is available in half-bus width(16 bit) configuration only. >>>>>> + >>>>>> +Required properties: >>>>>> +- compatible: Should be "xlnx,ps7-ddrc" or "xlnx,ps7-ddrc-1.00.a" >>>>> >>>>> Is this an or or a xor? >>>> >>>> Compatible string should be just xlnx,zynq-ddrc-1.00.a. >>>> Nothing with ps7. >>> >>> Isn't this vendor IP? IMHO, this should be something completely >>> different. Or if you want some Zynq-specific compat string it should >>> refer to an actual version string associated with Zynq. 1.00.a is not, >>> AFAIK. >> >> I have checked with Punnaiah that this is Synopsys DDR memory controller. >> Zynq is based on 1.4 version with some customization. >> It means I think reasonable solution is >> call it drivers/edac/synopsys_edac.c >> rename zynq_ in driver to synopsys_ and >> use xlnx,zynq-ddrc-1.00.a compatible string because zynq is not using >> clean synopsys version. >> >> I am not getting point why you don't like 1.00.a suffix here. >> Because of historical point of view compatible strings should be different >> for early silicon, silicon v1, silicon v2, silicon v3, etc >> but we haven't used it at all that's why we can use xilinx scheme >> which we are using for our soft IPs. > > Well, but you refer to Zynq which has silicon revisions you can use to > refer to a specific Zynq version. That matches data sheets. Zynq-1.00.a > is just completely made up and wouldn't be found in any data sheet. I didn't reply this one but we discussed this with Soren over phone. No problem to use Synopsys version A07 according TRM. Then compatible string is xlnx,zynq-ddrc-A07 and file name is synopsys_edac.c Soren: please correct me if I DDRC version is wrong. Regarding silicon revision in compatible string let's start new thread out of this ddrc one. Thanks, Michal -- To unsubscribe from this list: send the line "unsubscribe linux-doc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
