Re: [PATCH v4 1/3] dt-bindings: w1: UART 1-Wire bus

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 14/01/2024 15:47, Christoph Winklhofer wrote:
> On Sun, Jan 14, 2024 at 11:54:48AM +0100, Krzysztof Kozlowski wrote:
>> On 13/01/2024 19:04, Christoph Winklhofer wrote:
>>> On Fri, Jan 12, 2024 at 07:39:17PM -0600, Rob Herring wrote:
>>>> On Sat, Jan 06, 2024 at 05:02:24PM +0100, Christoph Winklhofer wrote:
>>>>> Add device tree binding for UART 1-Wire bus.
>>>>>
>>>>> Signed-off-by: Christoph Winklhofer <cj.winklhofer@xxxxxxxxx>
>>>>> ---
>>>>>  Documentation/devicetree/bindings/w1/w1-uart.yaml | 62 +++++++++++++++++++++++
>>>>>  1 file changed, 62 insertions(+)
>>>>>
>>>>> diff --git a/Documentation/devicetree/bindings/w1/w1-uart.yaml b/Documentation/devicetree/bindings/w1/w1-uart.yaml
>>>>> new file mode 100644
>>>>> index 000000000000..6b90693b2ca0
>>>>> --- /dev/null
>>>>> +++ b/Documentation/devicetree/bindings/w1/w1-uart.yaml
>>>>> @@ -0,0 +1,62 @@
>>>>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>>>>> +%YAML 1.2
>>>>> +---
>>>>> +$id: http://devicetree.org/schemas/w1/w1-uart.yaml#
>>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>> ...
>>>>> +properties:
>>>>> +  compatible:
>>>>> +    const: w1-uart
>>>>> +
>>>>> +  reset-speed:
>>>>> +    $ref: /schemas/types.yaml#/definitions/uint32
>>>>> +    default: 9600
>>>>> +    description: |
>>>>
>>>> Don't need '|' if no formatting
>>>>
>>>
>>> Ok.
>>>
>>>>> +      The baud rate for the 1-Wire reset and presence detect.
>>>>> +
>>>>> +  touch_0-speed:
>>>>
>>>> Don't use '_' in property names.
>>>>
>>>> I'm somewhat familar with 1-wire, but I don't get what 'touch' means 
>>>> here. I assume these are low and high times which are a function of the 
>>>> baudrate.
>>>>
>>>
>>> I change the name to 'write-0-speed' and 'write-1-speed'. The function
>>> in the w1-framework is named 'touch_bit' - therefore the previous
>>> naming. 
>>>
>>> It is the baud-rate used in the 1-Wire cycle to write a 0-Bit
>>> (write-0-speed) and to perform a 1-Wire cycle that writes a 1-Bit and
>>> reads a 0-Bit or 1-Bit (write-1-speed).
>>
>>
>> Then probably -bps:
>> https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml
> 
> The serial.yaml uses prefix -speed for the baud rate but I can change it
> to -bps.

Do you reference serial.yaml?

> 


Best regards,
Krzysztof





[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux FS]     [Yosemite Forum]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]     [Linux Resources]

  Powered by Linux