On Sun, Jan 14, 2024 at 04:55:42PM +0100, Krzysztof Kozlowski wrote: > On 14/01/2024 15:47, Christoph Winklhofer wrote: > > On Sun, Jan 14, 2024 at 11:54:48AM +0100, Krzysztof Kozlowski wrote: > >> On 13/01/2024 19:04, Christoph Winklhofer wrote: > >>> On Fri, Jan 12, 2024 at 07:39:17PM -0600, Rob Herring wrote: > >>>> On Sat, Jan 06, 2024 at 05:02:24PM +0100, Christoph Winklhofer wrote: > >>>>> Add device tree binding for UART 1-Wire bus. > >>>>> > >>>>> Signed-off-by: Christoph Winklhofer <cj.winklhofer@xxxxxxxxx> > >>>>> --- > >>>>> Documentation/devicetree/bindings/w1/w1-uart.yaml | 62 +++++++++++++++++++++++ > >>>>> 1 file changed, 62 insertions(+) > >>>>> > >>>>> diff --git a/Documentation/devicetree/bindings/w1/w1-uart.yaml b/Documentation/devicetree/bindings/w1/w1-uart.yaml > >>>>> new file mode 100644 > >>>>> index 000000000000..6b90693b2ca0 > >>>>> --- /dev/null > >>>>> +++ b/Documentation/devicetree/bindings/w1/w1-uart.yaml > >>>>> @@ -0,0 +1,62 @@ > >>>>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > >>>>> +%YAML 1.2 > >>>>> +--- > >>>>> +$id: http://devicetree.org/schemas/w1/w1-uart.yaml# > >>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml# > >>> ... > >>>>> +properties: > >>>>> + compatible: > >>>>> + const: w1-uart > >>>>> + > >>>>> + reset-speed: > >>>>> + $ref: /schemas/types.yaml#/definitions/uint32 > >>>>> + default: 9600 > >>>>> + description: | > >>>> > >>>> Don't need '|' if no formatting > >>>> > >>> > >>> Ok. > >>> > >>>>> + The baud rate for the 1-Wire reset and presence detect. > >>>>> + > >>>>> + touch_0-speed: > >>>> > >>>> Don't use '_' in property names. > >>>> > >>>> I'm somewhat familar with 1-wire, but I don't get what 'touch' means > >>>> here. I assume these are low and high times which are a function of the > >>>> baudrate. > >>>> > >>> > >>> I change the name to 'write-0-speed' and 'write-1-speed'. The function > >>> in the w1-framework is named 'touch_bit' - therefore the previous > >>> naming. > >>> > >>> It is the baud-rate used in the 1-Wire cycle to write a 0-Bit > >>> (write-0-speed) and to perform a 1-Wire cycle that writes a 1-Bit and > >>> reads a 0-Bit or 1-Bit (write-1-speed). > >> > >> > >> Then probably -bps: > >> https://github.com/devicetree-org/dt-schema/blob/main/dtschema/schemas/property-units.yaml > > > > The serial.yaml uses prefix -speed for the baud rate but I can change it > > to -bps. > > Do you reference serial.yaml? > No, serial.yaml is not referenced but 'onewire' will be a child-node of a serial-device which already defines baud rate related properties with -speed (e.g. max-speed although not used in w1-uart). Hence, I thought -speed is typically used for baud rates. Thanks, Christoph