On Mon 08 Feb 00:00 CST 2021, Baruch Siach wrote:
> From: Balaji Prakash J <bjagadee@xxxxxxxxxxxxxx>
>
> DWC_USB3_GFLADJ and DWC_USB3_GUCTL registers contain options
> to control the behavior of controller with respect to SOF and ITP.
> The reset values of these registers are aligned for 19.2 MHz
> reference clock source. This change will add option to override
> these settings for reference clock other than 19.2 MHz
>
> Tested on IPQ6018 SoC based CP01 board with 24MHz reference clock.
>
> Signed-off-by: Balaji Prakash J <bjagadee@xxxxxxxxxxxxxx>
> [ baruch: mention tested hardware ]
> Signed-off-by: Baruch Siach <baruch@xxxxxxxxxx>
> ---
> .../devicetree/bindings/usb/dwc3.txt | 5 ++
> drivers/usb/dwc3/core.c | 52 +++++++++++++++++++
> drivers/usb/dwc3/core.h | 12 +++++
> 3 files changed, 69 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt
> index 1aae2b6160c1..4ffa87b697dc 100644
> --- a/Documentation/devicetree/bindings/usb/dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/dwc3.txt
> @@ -89,6 +89,11 @@ Optional properties:
> - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ
> register for post-silicon frame length adjustment when the
> fladj_30mhz_sdbnd signal is invalid or incorrect.
> + - snps,quirk-ref-clock-adjustment: Value for GFLADJ_REFCLK_* fields of GFLADJ
> + register for reference clock other than 19.2 MHz is used.
What are typical values for this property? What unit does it have? How
does it actually relate to the frequency of the reference clock?
> + - snps,quirk-ref-clock-period: Value for REFCLKPER filed of GUCTL. This field
> + indicates in terms of nano seconds the period of ref_clk. To calculate the
> + ideal value, REFCLKPER = (1/ref_clk in Hz)*10^9.
Can't we make the dwc3 reference this clock and use clk_get_rate() and
then do this math in the driver?
> - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode
> only. Set this and rx-max-burst-prd to a valid,
> non-zero value 1-16 (DWC_usb31 programming guide
> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
> index 841daec70b6e..85e40ec8e23b 100644
> --- a/drivers/usb/dwc3/core.c
> +++ b/drivers/usb/dwc3/core.c
> @@ -325,6 +325,48 @@ static void dwc3_frame_length_adjustment(struct dwc3 *dwc)
> }
> }
>
> +/**
> + * dwc3_ref_clk_adjustment - Reference clock settings for SOF and ITP
> + * Default reference clock configurations are calculated assuming
> + * 19.2 MHz clock source. For other clock source, this will set
> + * configuration in DWC3_GFLADJ register
> + * @dwc: Pointer to our controller context structure
> + */
> +static void dwc3_ref_clk_adjustment(struct dwc3 *dwc)
> +{
> + u32 reg;
> +
> + if (dwc->ref_clk_adj == 0)
> + return;
> +
> + reg = dwc3_readl(dwc->regs, DWC3_GFLADJ);
> + reg &= ~DWC3_GFLADJ_REFCLK_MASK;
> + reg |= (dwc->ref_clk_adj << DWC3_GFLADJ_REFCLK_SEL);
reg = FIELD_SET(DWC3_GFLADJ_REFCLK_MASK, adj, reg);
Regards,
Bjorn
> + dwc3_writel(dwc->regs, DWC3_GFLADJ, reg);
> +}
> +
> +/**
> + * dwc3_ref_clk_period - Reference clock period configuration
> + * Default reference clock period is calculated assuming
> + * 19.2 MHz as clock source. For other clock source, this
> + * will set clock period in DWC3_GUCTL register
> + * @dwc: Pointer to our controller context structure
> + * @ref_clk_per: reference clock period in ns
> + */
> +static void dwc3_ref_clk_period(struct dwc3 *dwc)
> +{
> + u32 reg;
> +
> + if (dwc->ref_clk_per == 0)
> + return;
> +
> + reg = dwc3_readl(dwc->regs, DWC3_GUCTL);
> + reg &= ~DWC3_GUCTL_REFCLKPER_MASK;
> + reg |= (dwc->ref_clk_per << DWC3_GUCTL_REFCLKPER_SEL);
> + dwc3_writel(dwc->regs, DWC3_GUCTL, reg);
> +}
> +
> +
> /**
> * dwc3_free_one_event_buffer - Frees one event buffer
> * @dwc: Pointer to our controller context structure
> @@ -982,6 +1024,12 @@ static int dwc3_core_init(struct dwc3 *dwc)
> /* Adjust Frame Length */
> dwc3_frame_length_adjustment(dwc);
>
> + /* Adjust Reference Clock Settings */
> + dwc3_ref_clk_adjustment(dwc);
> +
> + /* Adjust Reference Clock Period */
> + dwc3_ref_clk_period(dwc);
> +
> dwc3_set_incr_burst_type(dwc);
>
> usb_phy_set_suspend(dwc->usb2_phy, 0);
> @@ -1351,6 +1399,10 @@ static void dwc3_get_properties(struct dwc3 *dwc)
> &dwc->hsphy_interface);
> device_property_read_u32(dev, "snps,quirk-frame-length-adjustment",
> &dwc->fladj);
> + device_property_read_u32(dev, "snps,quirk-ref-clock-adjustment",
> + &dwc->ref_clk_adj);
> + device_property_read_u32(dev, "snps,quirk-ref-clock-period",
> + &dwc->ref_clk_per);
>
> dwc->dis_metastability_quirk = device_property_read_bool(dev,
> "snps,dis_metastability_quirk");
> diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
> index 1b241f937d8f..469e94512414 100644
> --- a/drivers/usb/dwc3/core.h
> +++ b/drivers/usb/dwc3/core.h
> @@ -379,6 +379,14 @@
> #define DWC3_GFLADJ_30MHZ_SDBND_SEL BIT(7)
> #define DWC3_GFLADJ_30MHZ_MASK 0x3f
>
> +/* Global User Control Register*/
> +#define DWC3_GUCTL_REFCLKPER_MASK 0xffc00000
> +#define DWC3_GUCTL_REFCLKPER_SEL 22
> +
> +/* Global reference clock Adjustment Register */
> +#define DWC3_GFLADJ_REFCLK_MASK 0xffffff00
> +#define DWC3_GFLADJ_REFCLK_SEL 8
> +
> /* Global User Control Register 2 */
> #define DWC3_GUCTL2_RST_ACTBITLATER BIT(14)
>
> @@ -956,6 +964,8 @@ struct dwc3_scratchpad_array {
> * @regs: base address for our registers
> * @regs_size: address space size
> * @fladj: frame length adjustment
> + * @ref_clk_adj: reference clock adjustment
> + * @ref_clk_per: reference clock period configuration
> * @irq_gadget: peripheral controller's IRQ number
> * @otg_irq: IRQ number for OTG IRQs
> * @current_otg_role: current role of operation while using the OTG block
> @@ -1118,6 +1128,8 @@ struct dwc3 {
> enum usb_dr_mode role_switch_default_mode;
>
> u32 fladj;
> + u32 ref_clk_adj;
> + u32 ref_clk_per;
> u32 irq_gadget;
> u32 otg_irq;
> u32 current_otg_role;
> --
> 2.30.0
>
