Re: [PATCH V5 1/4] backlight: qcom-wled: convert the wled bindings to .yaml format

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Apr 07, 2020 at 09:17:07PM +0530, Kiran Gunda wrote:
> Convert the qcom-wled bindings from .txt to .yaml format.
> Also replace PM8941 to WLED3 and PMI8998 to WLED4.
> 
> Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
> Signed-off-by: Subbaraman Narayanamurthy <subbaram@xxxxxxxxxxxxxx>
> Acked-by: Daniel Thompson <daniel.thompson@xxxxxxxxxx>
> ---
>  .../bindings/leds/backlight/qcom-wled.txt          | 154 ----------------
>  .../bindings/leds/backlight/qcom-wled.yaml         | 201 +++++++++++++++++++++
>  2 files changed, 201 insertions(+), 154 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt
>  create mode 100644 Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml


> diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> new file mode 100644
> index 0000000..770e780
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml
> @@ -0,0 +1,201 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Binding for Qualcomm Technologies, Inc. WLED driver
> +
> +maintainers:
> +  - Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> +  - Kiran Gunda <kgunda@xxxxxxxxxxxxxx>
> +
> +description: |
> +  WLED (White Light Emitting Diode) driver is used for controlling display
> +  backlight that is part of PMIC on Qualcomm Technologies, Inc. reference
> +  platforms. The PMIC is connected to the host processor via SPMI bus.
> +
> +properties:
> +  compatible:
> +    enum:
> +      - qcom,pm8941-wled
> +      - qcom,pmi8998-wled
> +      - qcom,pm660l-wled
> +
> +  reg:
> +    maxItems: 1
> +
> +  default-brightness:
> +    description:
> +      brightness value on boot.
> +    minimum: 0
> +    maximum: 4095
> +    default: 2048
> +
> +  label: true
> +
> +  qcom,cs-out:
> +    description:
> +      enable current sink output.
> +      This property is supported only for WLED3.
> +    type: boolean
> +
> +  qcom,cabc:
> +    description:
> +      enable content adaptive backlight control.
> +    type: boolean
> +
> +  qcom,ext-gen:
> +    description:
> +      use externally generated modulator signal to dim.
> +      This property is supported only for WLED3.
> +    type: boolean
> +
> +  qcom,current-limit:
> +    description:
> +      mA; per-string current limit.
> +      This property is supported only for WLED3.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +    default: 20
> +    minimum: 0
> +    maximum: 25
> +    multipleOf: 1

No point in defining a multiple of 1.

> +
> +  qcom,current-limit-microamp:
> +    description:
> +      uA; per-string current limit.
> +    default: 25
> +    minimum: 0
> +    maximum: 30000
> +    multipleOf: 25
> +
> +  qcom,current-boost-limit:
> +    description:
> +      mA; boost current limit.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  qcom,switching-freq:
> +    description:
> +      kHz; switching frequency.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ]
> +
> +  qcom,ovp:
> +    description:
> +      V; Over-voltage protection limit.
> +      This property is supported only for WLED3.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [ 27, 29, 32, 35 ]
> +      - default: 29
> +
> +  qcom,ovp-millivolt:
> +    description:
> +      Over-voltage protection limit. This property is for WLED4 only.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +      - enum: [ 18100, 19600, 29600, 31100 ]
> +      - default: 29600
> +
> +  qcom,num-strings:
> +    description:
> +      number of led strings attached.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +
> +  qcom,enabled-strings:
> +    description:
> +      Array of the WLED strings numbered from 0 to 3. Each
> +      string of leds are operated individually. Specify the
> +      list of strings used by the device. Any combination of
> +      led strings can be used.
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32-array
> +    minItems: 1
> +    maxItems: 4
> +
> +  qcom,external-pfet:
> +    description:
> +      Specify if external PFET control for short circuit
> +      protection is used. This property is supported only
> +      for WLED4.
> +    type: boolean
> +        
> +  qcom,auto-string-detection:
> +    description:
> +      Enables auto-detection of the WLED string configuration.
> +      This feature is not supported for WLED3.
> +    type: boolean
> +
> +allOf:
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            const: qcom,pm8941-wled
> +
> +    then:
> +      properties:
> +        qcom,current-boost-limit:
> +           enum: [ 105, 385, 525, 805, 980, 1260, 1400, 1680 ]
> +           default: 805
> +
> +        qcom,switching-freq:
> +           default: 1600
> +
> +        qcom,num-strings:
> +           enum: [ 1, 2, 3 ]
> +  
> +        interrupts:
> +          items:
> +            - description: over voltage protection interrupt.
> +
> +        interrupt-names:
> +          items:
> +            - const: ovp
> +
> +    else:
> +      properties:
> +        qcom,current-boost-limit:
> +           enum: [ 105, 280, 450, 620, 970, 1150, 1300, 1500 ]
> +           default: 970
> +
> +        qcom,switching-freq:
> +           default: 800
> +
> +        qcom,num-strings:
> +           enum: [ 1, 2, 3, 4 ]
> +
> +        interrupts:
> +          items:
> +            - description: over voltage protection interrupt.
> +            - description: short circuit interrupt.
> +
> +        interrupt-names:
> +          items:
> +            - const: ovp
> +            - const: short

Move these 2 props to the main section adding a 'minItems: 1'. Then just 
define 'minItems: 2' here and 'maxItems: 1' in the 'then' clause.

> +
> +required:
> +  - compatible
> +  - reg
> +  - label

Add:

additionalProperties: false

> +
> +examples:
> +  - |
> +    backlight@d800 {
> +        compatible = "qcom,pm8941-wled";
> +        reg = <0xd800 0x100>;
> +        label = "backlight";
> +
> +        qcom,cs-out;
> +        qcom,current-limit = <20>;
> +        qcom,current-boost-limit = <805>;
> +        qcom,switching-freq = <1600>;
> +        qcom,ovp = <29>;
> +        qcom,num-strings = <2>;
> +        qcom,enabled-strings = <0 1>;
> +     };
> -- 
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
>  a Linux Foundation Collaborative Project
> 



[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux