On 01/31/2018 09:50 PM, Rob Clark wrote:
On Wed, Jan 31, 2018 at 1:40 AM, Archit Taneja <architt@xxxxxxxxxxxxxx> wrote:
On 01/29/2018 10:45 PM, Rob Herring wrote:
On Wed, Jan 17, 2018 at 03:04:47PM +0530, Archit Taneja wrote:
Add the compatible string for 14nm DSI PHY (used in MSM8996/APQ8096).
From 14nm PHY onwards, the "dsi_phy_regulator" reg-name is not required,
but "dsi_phy_lane" reg-name is. Update the doc to specify the reg-names
each PHY revision needs.
Cc: Rob Herring <robh@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/display/msm/dsi.txt | 13
+++++++++++--
1 file changed, 11 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt
b/Documentation/devicetree/bindings/display/msm/dsi.txt
index 9c3ad6bbb9f0..26a1796b7145 100644
--- a/Documentation/devicetree/bindings/display/msm/dsi.txt
+++ b/Documentation/devicetree/bindings/display/msm/dsi.txt
@@ -86,12 +86,19 @@ Required properties:
* "qcom,dsi-phy-28nm-lp"
* "qcom,dsi-phy-20nm"
* "qcom,dsi-phy-28nm-8960"
-- reg: Physical base address and length of the registers of PLL, PHY and
PHY
- regulator
+ * "qcom,dsi-phy-14nm"
+- reg: Physical base address and length of the registers of PLL, PHY.
Some
+ revisions require the PHY regulator base address, whereas others
require the
+ PHY lane base address. See below for each PHY revision.
- reg-names: The names of register regions. The following regions are
required:
+ For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY:
* "dsi_pll"
* "dsi_phy"
* "dsi_phy_regulator"
+ For DSI 14nm PHY:
+ * "dsi_pll"
+ * "dsi_phy"
+ * "dsi_phy_lane"
- clock-cells: Must be 1. The DSI PHY block acts as a clock provider,
creating
2 clocks: A byte clock (index 0), and a pixel clock (index 1).
- power-domains: Should be <&mmcc MDSS_GDSC>.
@@ -102,6 +109,8 @@ Required properties:
- vddio-supply: phandle to vdd-io regulator device node
For 20nm PHY:
- vddio-supply: phandle to vdd-io regulator device node
+- vcca-supply: phandle to vcca regulator device node
Did you mean to add this?
Yes, I didn't intend it to be a part of this patch, but this supply is
indeed needed for the
20nm PHY. I'll move this to a separate patch.
actually, this looks correct, just formatted counter-intuitively by
git-format-patch..
vcca-supply for 20nm was introduced by "dt-bindings: display: msm/dsi:
Fix the PHY regulator supply props", but when 14nm phy is added in
this patch, it shows the addition of same line beneath 14nm PHY as an
addition above the line.
So I don't think it needs to be split up.
Oh yeah, you're right. I guess this is okay as is, then.
Thanks,
Archit
BR,
-R
Thanks,
Archit
+ For 14nm PHY:
- vcca-supply: phandle to vcca regulator device node
Optional properties:
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum,
hosted by The Linux Foundation
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
