On Fri, 19 Apr 2024 at 08:31, Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx> wrote: > > On Fri, 19 Apr 2024 at 18:27, Sumit Garg <sumit.garg@xxxxxxxxxx> wrote: > > > > On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@xxxxxxxxxx> wrote: > > > > > > Hi Bjorn, Konrad, > > > > > > On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@xxxxxxxxxx> wrote: > > > > > > > > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge > > > > Box Core board based on the Qualcomm APQ8016E SoC. For more information > > > > refer to the product page [1]. > > > > > > > > One of the major difference from db410c is serial port where HMIBSC board > > > > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux > > > > configured via gpio99 and gpio100). > > > > > > > > Support for Schneider Electric HMIBSC. Features: > > > > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306) > > > > - 1GiB RAM > > > > - 8GiB eMMC, SD slot > > > > - WiFi and Bluetooth > > > > - 2x Host, 1x Device USB port > > > > - HDMI > > > > - Discrete TPM2 chip over SPI > > > > - USB ethernet adaptors (soldered) > > > > > > > > This series is a v2 since v1 of this DTS file has been reviewed on the > > > > U-Boot mailing list [2]. > > > > > > > > Changes in v5: > > > > - Addressed another nitpick from Stephen. > > > > - Collected Stephen's review tag. > > > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC > > > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt > > > > still not converted to YAML format. > > > > > > > > > > I haven't seen any further comments on this series, can you help to pick it up? > > > > Gentle reminder. > > I see an email from Rob. At least GPIO-related warnings are related to HMIBSC > I suppose you are referring to: arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: pmic@0: gpio@c000:gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM', 'NC', 'NC'] is too short from schema $id: http://devicetree.org/schemas/mfd/qcom,spmi-pmic.yaml# arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dtb: gpio@c000: gpio-line-names: ['USB_HUB_RESET_N_PM', 'USB_SW_SEL_PM', 'NC', 'NC'] is too short from schema $id: http://devicetree.org/schemas/pinctrl/qcom,pmic-gpio.yaml# I am really not sure as to why those warnings are being reported for v5 and not reported for v4 here [1]. Also, there are only 4 PMIC GPIOs available on PM8916 out of which only 2 are connected on HMIBSC and the other 2 are not connected. AFAICT, these seem to be false warning reports or am I missing something? [1] https://lore.kernel.org/lkml/171155390164.3454213.14779164019451021567.robh@xxxxxxxxxx/ -Sumit > > -- > With best wishes > Dmitry
