On Tue, 9 Apr 2024 at 23:24, Sumit Garg <sumit.garg@xxxxxxxxxx> wrote: > > Hi Bjorn, Konrad, > > On Wed, 3 Apr 2024 at 10:04, Sumit Garg <sumit.garg@xxxxxxxxxx> wrote: > > > > Add Schneider Electric HMIBSC board DTS. The HMIBSC board is an IIoT Edge > > Box Core board based on the Qualcomm APQ8016E SoC. For more information > > refer to the product page [1]. > > > > One of the major difference from db410c is serial port where HMIBSC board > > uses UART1 as the debug console with a default RS232 mode (UART1 mode mux > > configured via gpio99 and gpio100). > > > > Support for Schneider Electric HMIBSC. Features: > > - Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306) > > - 1GiB RAM > > - 8GiB eMMC, SD slot > > - WiFi and Bluetooth > > - 2x Host, 1x Device USB port > > - HDMI > > - Discrete TPM2 chip over SPI > > - USB ethernet adaptors (soldered) > > > > This series is a v2 since v1 of this DTS file has been reviewed on the > > U-Boot mailing list [2]. > > > > Changes in v5: > > - Addressed another nitpick from Stephen. > > - Collected Stephen's review tag. > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt > > still not converted to YAML format. > > > > I haven't seen any further comments on this series, can you help to pick it up? Gentle reminder. -Sumit > > > Changes in v4: > > - Dropped IRQ_TYPE_EDGE_FALLING for pm8916_resin given the expectations > > of Linux kernel driver. Instead depend on systemd workaround suggested > > by Caleb to get expected HMIBSC reset behaviour. > > - Incorporated further DT coding style comments from Stephen. > > - Warnings reported by Rob's DT check bot aren't related to HMIBSC > > board DTS but rather they are due to msm8916.dtsi or extcon-usb-gpio.txt > > still not converted to YAML format. > > > > Changes in v3: > > - Picked up tags. > > - Fixed further DT schema warnings. > > - Configure resin/power button interrupt as falling edge. > > - Incorporate DTS coding style comments from Krzysztof and Konrad. > > > > Changes in v2: > > - Fix DT schema warnings. > > - Incorporate suggestions from Stephan. > > - Document UART1 mode GPIOs based mux. > > > > [1] https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/ > > [2] https://patchwork.ozlabs.org/project/uboot/patch/20240311111027.44577-6-sumit.garg@xxxxxxxxxx/ > > > > Sumit Garg (3): > > dt-bindings: vendor-prefixes: Add Schneider Electric > > dt-bindings: arm: qcom: Add Schneider Electric HMIBSC board > > arm64: dts: qcom: apq8016: Add Schneider HMIBSC board DTS > > > > .../devicetree/bindings/arm/qcom.yaml | 1 + > > .../devicetree/bindings/vendor-prefixes.yaml | 2 + > > arch/arm64/boot/dts/qcom/Makefile | 1 + > > .../dts/qcom/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++ > > 4 files changed, 495 insertions(+) > > create mode 100644 arch/arm64/boot/dts/qcom/apq8016-schneider-hmibsc.dts > > > > -- > > 2.34.1 > >
