On Sat, 10 Feb 2024 at 12:44, Krishna Kurapati PSSNV
<quic_kriskura@xxxxxxxxxxx> wrote:
>
> > Krishna, when you make v2 can you update the wording about the USB 2.0
> > mux? Maybe something like "which by default on boot is selected to mux
> > to the external port on the board (with the other option being a test
> > point)." instead of the wording I originally had? That way the
> > information Dmitry requested here is easily accessible in the future.
> >
> >>
> >>>
>
> [...]
>
> >>>>>> };
> >>>>>
> >>>>> Isn't gpio-hog the preferred way to describe that ?
> >>>>
> >>>> That depends. As this pinctrl describes board configuration, I'd agree
> >>>> with Neil.
> >>>
> >>> I unfortunately don't have the experience with gpio-hog to weigh in
> >>> here, but wouldn't be opposed to Krishna switching it if that's what's
> >>> recommended for this type of thing.
> >>
> >> Quoting gpio.txt:
> >>
> >> The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism
> >> providing automatic GPIO request and configuration as part of the
> >> gpio-controller's driver probe function.
> >>
> >> See sdm845-pinctrl.yaml for an example of the gpio-hog node.
> >
> > Thanks, that seems like the way to go. Krishna please take note of this
> > for v2!
> >
>
> Hi Andrew,
>
> Can you help test the following patch. It is just an add-on to your
> original one. I don't have a SA8540P Ride at the moment and getting one
> might take time. Incase you can confirm this patch is working. I can
> push v2 of this series.
>
>
> diff --git
> a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml
> b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml
> index ed344deaf8b9..aa42ac5a3197 100644
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sc8280xp-tlmm.yaml
> @@ -36,6 +36,10 @@ patternProperties:
> $ref: "#/$defs/qcom-sc8280xp-tlmm-state"
> additionalProperties: false
>
> + "-hog(-[0-9]+)?$":
> + required:
> + - gpio-hog
> +
> $defs:
> qcom-sc8280xp-tlmm-state:
> type: object
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> index b04f72ec097c..aa0cec0b4cc2 100644
> --- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -503,6 +503,18 @@ &usb_2_qmpphy0 {
> status = "okay";
> };
>
> +&usb_2 {
> + pinctrl-0 = <&usb2_en_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + phy-names = "usb2-port0", "usb3-port0";
> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
> +};
> +
> &xo_board_clk {
> clock-frequency = <38400000>;
> };
> @@ -655,4 +667,19 @@ wake-pins {
> bias-pull-up;
> };
> };
> +
> + usb2-en-hog {
> + gpio-hog;
> + gpios = <24 GPIO_ACTIVE_LOW>;
> + output-low;
> + };
> +
> + usb2_en_state: usb2-en-state {
If you are using gpio-hog, you don't need this state. The pinctrl /
gpio core will use the hog instead.
> + /* TS3USB221A USB2.0 mux select */
> + pins = "gpio24";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
>
>
> Regards,
> Krishna,
--
With best wishes
Dmitry
