Re: [PATCH v5 02/20] dt-bindings: thermal: tsens: support per-sensor calibration cells

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 29/12/2022 12:49, Dmitry Baryshkov wrote:
> On Thu, 29 Dec 2022 at 10:35, Krzysztof Kozlowski
> <krzysztof.kozlowski@xxxxxxxxxx> wrote:
>>
>> On 29/12/2022 04:00, Dmitry Baryshkov wrote:
>>> Allow specifying the exact calibration mode and calibration data as nvmem
>>> cells, rather than specifying just a single calibration data blob.
>>>
>>> Note, unlike the vendor kernel the calibration data uses hw_ids rather
>>> than software sensor indices (to match actual tsens usage in
>>> thermal zones).
>>>
>>> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
>>> ---
>>>  .../bindings/thermal/qcom-tsens.yaml          | 95 +++++++++++++++++--
>>>  1 file changed, 85 insertions(+), 10 deletions(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
>>> index f3660af0b3bf..4bb689f4602d 100644
>>> --- a/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
>>> +++ b/Documentation/devicetree/bindings/thermal/qcom-tsens.yaml
>>> @@ -81,18 +81,63 @@ properties:
>>>      maxItems: 2
>>>
>>>    nvmem-cells:
>>> -    minItems: 1
>>> -    maxItems: 2
>>> -    description:
>>> -      Reference to an nvmem node for the calibration data
>>> +    oneOf:
>>> +      - minItems: 1
>>> +        maxItems: 2
>>> +        description:
>>> +          Reference to an nvmem node for the calibration data
>>> +      - minItems: 5
>>> +        maxItems: 35
>>> +        description: |
>>> +          Reference to nvmem cells for the calibration mode, two calibration
>>> +          bases and two cells per each sensor
>>>
>>>    nvmem-cell-names:
>>> -    minItems: 1
>>> -    items:
>>> -      - const: calib
>>> -      - enum:
>>> -          - calib_backup
>>> -          - calib_sel
>>> +    oneOf:
>>> +      - minItems: 1
>>> +        items:
>>> +          - const: calib
>>> +          - enum:
>>> +              - calib_backup
>>> +              - calib_sel
>>> +      - minItems: 5
>>> +        items:
>>> +          enum:
>>
>> This should not be an enum but a list of const... unless "holes" are
>> expected (e.g. s0_p1 and s5_p2, without ones in between).
> 
> Yes, this is the case. See the msm8916.dtsi changes. There is no
> sensor with hw_id 3, so the sequence is: ... s2_p1, s2_p2, s4_p1,
> s4_p2,....
> 
> Same applies to the msm8939 (no sensor #4).
> 
> Note: if there was support for the prefixItems, I'd have probably
> marked mode/base1/base2 to be the first items of the array.

Then how about list of const items and patterns? Would be similar number
of lines, just a bit more complicated pattern instead of simple string
to enum.

Best regards,
Krzysztof




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux