Historically the tsens driver fetches the calibration data as a blob and then parses the blob on its own. This results in semi-duplicated code spreading over the platform-specific functions. This patch series changes tsens calibration code to per-value nvmem cells rather than parsing the blob in the driver. For backwards compatibility the old code is left in place for msm8916, msm8974 and qcs404, the platforms which have in-tree DT files. For all other affected platforms the old parsing code has been dropped as a part of this series. The code was tested on msm8916 and qcs404 only. Note: the DTs changes depend on driver changes. Tsens driver will not work if DT patches are merged, but the driver bits are not. As the thermal sense is critical for device safety, I'kindly ask to have an immutable branch with the driver changes that can be merged into the msm-dts tree. Note2: I still have included patches to drop legacy support for 8939 (msm8939.dtsi is on the list, patch to convert it to the proposed bindings is available at [1]) and 8976 (msm8976.dtsi and msm8956.dtsi, which use single-blob bindings, have been accepted for 6.2, dropping old bindings support depends on mutual consensuns of platform and thermal code maintainers). Corresponding patches are the last ones in the thermal part of the series, thus if they are declined, the reset of the series still can be applied without any problems. [1] https://pastebin.ubuntu.com/p/rfkZgy767K/ Changes since v4: - Changed DT bindings to use HW sensor ids rather than bare indices. This follows the usage of hw_ids in thermal-sensors specifications (and corresponds to the ID visible in debugfs). Previously there was no correspondence, which resulted e.g. in usage of s0_p1/s0_p2 for sensor 0, but s4_p1/s4_p2 for the sensor 5 on the msm8916 platform). - Reworked msm8939 code to ignore the sensor10. It is available only on latest hw revision, it doesn't seem to be actually used and it also wasn't covered by the old single-blob bindings because of the parsing error. - Fixed missing include reported by testing robot. Changes since v3: - Added a patch to fix the tsens compatible string on msm8956 SoC, - Fixed num-sensors and slope coefficients for the msm8939 SoC, - Rewrote code supporting old bindings into the simple data-driven parser common to all legacy platforms which made dropping support for old bindings less demanding. Changes since v2: - Made init_8956 static, as pointed out by the testing robot and by AngeloGioacchino Del Regno. Changes since the RFC: - Sorted out the msm8976/msm8956, custom slopes are used only for msm8956, - Implemented proper support for msm8974/apq8084, - Added tsens_calibrate_common() and ops_v0_1 which can be used in common cases, - Removed superfluous identity hw_ids - Fixed calibration calculation in tsens_calibrate_nvmem() for ONE_PT_CALIB case Dmitry Baryshkov (20): dt-bindings: thermal: tsens: add msm8956 compat dt-bindings: thermal: tsens: support per-sensor calibration cells dt-bindings: thermal: tsens: add per-sensor cells for msm8974 thermal/drivers/tsens: Drop unnecessary hw_ids thermal/drivers/tsens: Drop msm8976-specific defines thermal/drivers/tsens: Sort out msm8976 vs msm8956 data thermal/drivers/tsens: fix slope values for msm8939 thermal/drivers/tsens: limit num_sensors to 9 for msm8939 thermal/drivers/tsens: Support using nvmem cells for calibration data thermal/drivers/tsens: Support using nvmem cells for msm8974 calibration thermal/drivers/tsens: Rework legacy calibration data parsers thermal/drivers/tsens: Drop single-cell code for mdm9607 thermal/drivers/tsens: Drop single-cell code for msm8939 thermal/drivers/tsens: Drop single-cell code for msm8976/msm8956 arm64: dts: qcom: msm8956: use SoC-specific compat for tsens arm64: dts: qcom: msm8916: specify per-sensor calibration cells arm64: dts: qcom: msm8976: specify per-sensor calibration cells arm64: dts: qcom: qcs404: specify per-sensor calibration cells ARM: dts: qcom-msm8974: specify per-sensor calibration cells ARM: dts: qcom-apq8084: specify per-sensor calibration cells .../bindings/thermal/qcom-tsens.yaml | 154 +++- arch/arm/boot/dts/qcom-apq8084.dtsi | 313 ++++++++- arch/arm/boot/dts/qcom-msm8974.dtsi | 313 ++++++++- arch/arm64/boot/dts/qcom/msm8916.dtsi | 85 ++- arch/arm64/boot/dts/qcom/msm8956.dtsi | 4 + arch/arm64/boot/dts/qcom/msm8976.dtsi | 153 +++- arch/arm64/boot/dts/qcom/qcs404.dtsi | 145 +++- drivers/thermal/qcom/tsens-v0_1.c | 655 +++++------------- drivers/thermal/qcom/tsens-v1.c | 340 +++------ drivers/thermal/qcom/tsens.c | 168 +++++ drivers/thermal/qcom/tsens.h | 46 +- 11 files changed, 1611 insertions(+), 765 deletions(-) -- 2.39.0
