Some remote processors (e.g. QCS404 CDSP, SC7180 MPSS/MSS) can be brought
to life using two different bindings:
1. PIL (Peripheral Image Loader)
2. PAS (Peripheral Authentication Service)
They still describe the same hardware - firmware load for remote
processor - but use different methods to communicate with that
processor.
For these SoCs, the qcom,adsp.yaml bindings were describing the PAS
method, however for easier customization of board DTS, the bindings
combined additional properties from PIL: reset lines, qcom,halt-regs and
additional clocks. The devices and Linux kernel drivers, when
instantiated as PAS, do not use these properties, so drop them from the
bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
Changes since v2:
1. New patch
---
.../bindings/remoteproc/qcom,adsp.yaml | 113 +-----------------
1 file changed, 4 insertions(+), 109 deletions(-)
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
index db9e0f0c2bea..e3e617315aef 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
@@ -61,11 +61,11 @@ properties:
clocks:
minItems: 1
- maxItems: 8
+ maxItems: 2
clock-names:
minItems: 1
- maxItems: 8
+ maxItems: 2
interconnects:
maxItems: 1
@@ -90,14 +90,6 @@ properties:
- const: stop-ack
- const: shutdown-ack
- resets:
- minItems: 1
- maxItems: 3
-
- reset-names:
- minItems: 1
- maxItems: 3
-
cx-supply:
description: Phandle to the CX regulator
@@ -135,18 +127,6 @@ properties:
items:
- const: stop
- qcom,halt-regs:
- $ref: /schemas/types.yaml#/definitions/phandle-array
- items:
- - items:
- - description: Phandle reference to a syscon representing TCSR
- - description: offsets within syscon for q6 halt registers
- - description: offsets within syscon for modem halt registers
- - description: offsets within syscon for nc halt registers
- description:
- Phandle reference to a syscon representing TCSR followed by the
- three offsets within syscon for q6, modem and nc halt registers.
-
smd-edge:
$ref: /schemas/remoteproc/qcom,smd-edge.yaml#
description:
@@ -184,7 +164,9 @@ allOf:
- qcom,msm8996-slpi-pil
- qcom,msm8998-adsp-pas
- qcom,qcs404-adsp-pas
+ - qcom,qcs404-cdsp-pas
- qcom,qcs404-wcss-pas
+ - qcom,sc7180-mpss-pas
- qcom,sc7280-mpss-pas
- qcom,sc8180x-adsp-pas
- qcom,sc8180x-cdsp-pas
@@ -238,60 +220,6 @@ allOf:
- const: xo
- const: aggre2
- - if:
- properties:
- compatible:
- contains:
- enum:
- - qcom,qcs404-cdsp-pas
- then:
- properties:
- clocks:
- items:
- - description: XO clock
- - description: SWAY clock
- - description: TBU clock
- - description: BIMC clock
- - description: AHB AON clock
- - description: Q6SS SLAVE clock
- - description: Q6SS MASTER clock
- - description: Q6 AXIM clock
- clock-names:
- items:
- - const: xo
- - const: sway
- - const: tbu
- - const: bimc
- - const: ahb_aon
- - const: q6ss_slave
- - const: q6ss_master
- - const: q6_axim
-
- - if:
- properties:
- compatible:
- contains:
- enum:
- - qcom,sc7180-mpss-pas
- then:
- properties:
- clocks:
- items:
- - description: XO clock
- - description: IFACE clock
- - description: BUS clock
- - description: NAC clock
- - description: SNOC AXI clock
- - description: MNOC AXI clock
- clock-names:
- items:
- - const: xo
- - const: iface
- - const: bus
- - const: nav
- - const: snoc_axi
- - const: mnoc_axi
-
- if:
properties:
compatible:
@@ -520,39 +448,6 @@ allOf:
items:
- const: nsp
- - if:
- properties:
- compatible:
- contains:
- enum:
- - qcom,qcs404-cdsp-pas
- then:
- properties:
- resets:
- items:
- - description: CDSP restart
- reset-names:
- items:
- - const: restart
-
- - if:
- properties:
- compatible:
- contains:
- enum:
- - qcom,sc7180-mpss-pas
- - qcom,sc7280-mpss-pas
- then:
- properties:
- resets:
- items:
- - description: MSS restart
- - description: PDC reset
- reset-names:
- items:
- - const: mss_restart
- - const: pdc_reset
-
- if:
properties:
compatible:
--
2.34.1
