[PATCH 1/6] dt-bindings: regulator: qcom,spmi-regulator: Convert to dtschema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Convert the bindings of Qualcomm SPMI regulators to DT schema.

Signed-off-by: Robert Marko <robimarko@xxxxxxxxx>
---
I am aware that syscon alone is not really acceptable, its converted
directly from the old text bindings.

There is also the issue of some MSM8994, MSM8996 and APQ8096 devices using
'#address-cells', '#size-cells', some even defining reg property for
regulators.

Any advice on how to solve these issues is appreciated.
---
 .../regulator/qcom,spmi-regulator.yaml        | 176 ++++++++++++++++++
 1 file changed, 176 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml

diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml
new file mode 100644
index 000000000000..f7da310f1845
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SPMI Regulators
+
+maintainers:
+  - Robert Marko <robert.marko@xxxxxxxxxx>
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm660-regulators
+      - qcom,pm660l-regulators
+      - qcom,pm8004-regulators
+      - qcom,pm8005-regulators
+      - qcom,pm8226-regulators
+      - qcom,pm8841-regulators
+      - qcom,pm8916-regulators
+      - qcom,pm8941-regulators
+      - qcom,pm8950-regulators
+      - qcom,pm8994-regulators
+      - qcom,pmi8994-regulators
+      - qcom,pms405-regulators
+
+  qcom,saw-reg:
+    description: Reference to syscon node defining the SAW registers
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8941-regulators
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: Over-current protection interrupt for 5V S1
+            - description: Over-current protection interrupt for 5V S2
+        interrupt-names:
+          items:
+            - const: ocp-5vs1
+            - const: ocp-5vs2
+
+patternProperties:
+  ".*-supply$":
+    description: Input supply phandle(s) for this node
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  "^((s|l|lvs|5vs)[0-9]*)$":
+    description: List of regulators and its properties
+    $ref: regulator.yaml#
+
+    properties:
+      qcom,ocp-max-retries:
+        description:
+          Maximum number of times to try toggling a voltage switch off and
+          back on as a result of consecutive over current events
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+      qcom,ocp-retry-delay:
+        description:
+          Time to delay in milliseconds between each voltage switch toggle
+          after an over current event takes place
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+      qcom,pin-ctrl-enable:
+        description:
+          Bit mask specifying which hardware pins should be used to enable the
+          regulator, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 15
+
+      qcom,pin-ctrl-hpm:
+        description:
+          Bit mask specifying which hardware pins should be used to force the
+          regulator into high power mode, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+          BIT(4) = follow PMIC awake state
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 31
+
+      qcom,vs-soft-start-strength:
+        description:
+          This property sets the soft start strength for voltage switch type
+          regulators.
+          Supported values are
+          0 = 0.05 uA
+          1 = 0.25 uA
+          2 = 0.55 uA
+          3 = 0.75 uA
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3
+
+      qcom,saw-slave:
+        description: SAW controlled gang slave. Will not be configured.
+        type: boolean
+
+      qcom,saw-leader:
+        description:
+          SAW controlled gang leader. Will be configured as SAW regulator.
+        type: boolean
+
+      unevaluatedProperties: false
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+
+examples:
+  - |
+    regulators {
+      compatible = "qcom,pm8941-regulators";
+      vdd_l1_l3-supply = <&s1>;
+
+      s1: s1 {
+        regulator-min-microvolt = <1300000>;
+        regulator-max-microvolt = <1400000>;
+      };
+
+      l1: l1 {
+        regulator-min-microvolt = <1225000>;
+        regulator-max-microvolt = <1300000>;
+      };
+    };
+
+  - |
+    saw3: syscon@9a10000 {
+      compatible = "syscon";
+      reg = <0x9a10000 0x1000>;
+    };
+
+    regulators {
+      compatible = "qcom,pm8994-regulators";
+      qcom,saw-reg = <&saw3>;
+
+      s8 {
+        qcom,saw-slave;
+      };
+
+      s9 {
+        qcom,saw-slave;
+      };
+
+      s10 {
+        qcom,saw-slave;
+      };
+
+      pm8994_s11_saw: s11 {
+        qcom,saw-leader;
+        regulator-always-on;
+        regulator-min-microvolt = <900000>;
+        regulator-max-microvolt = <1140000>;
+      };
+    };
+...
-- 
2.36.1




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux