Re: [PATCH v3] ARM: dts: qcom: Add initial IFC6540 board device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sep 5, 2014, at 9:26 AM, Andreas Färber <afaerber@xxxxxxx> wrote:

> Hi,
> 
> Am 03.09.2014 18:50, schrieb Georgi Djakov:
>> Add basic support for the IFC6540 single-board computer boards, that are
>> based on the APQ8084 SoC. This patch adds the initial device tree and the
>> neccessary nodes required for enabling the serial port and eMMC.
>> 
>> Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
>> ---
>> Changes since v2:
>> - Squashed all patches into one. (suggested by Kumar Gala)
>> 
>> Changes since v1:
>> - This time add linux-arm-msm list to the CC.
>> - Include a third patch for enabling the eMMC.
>> 
>> arch/arm/boot/dts/Makefile                 |    1 +
>> arch/arm/boot/dts/qcom-apq8084-ifc6540.dts |   23 +++++++++++++++++++++++
>> arch/arm/boot/dts/qcom-apq8084.dtsi        |   23 +++++++++++++++++++++++
>> 3 files changed, 47 insertions(+)
>> create mode 100644 arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
>> 
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index b022972..df8453a 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -345,6 +345,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += \
>> 	qcom-apq8064-ifc6410.dtb \
>> 	qcom-apq8074-dragonboard.dtb \
>> +	qcom-apq8084-ifc6540.dtb \
>> 	qcom-apq8084-mtp.dtb \
>> 	qcom-msm8660-surf.dtb \
>> 	qcom-msm8960-cdp.dtb
>> diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
>> new file mode 100644
>> index 0000000..c9ff108
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
>> @@ -0,0 +1,23 @@
>> +#include "qcom-apq8084.dtsi"
>> +
>> +/ {
>> +	model = "Qualcomm APQ8084/IFC6540";
>> +	compatible = "qcom,apq8084-ifc6540", "qcom,apq8084";
>> +
>> +	soc {
>> +		serial@f995e000 {
>> +			status = "okay";
>> +		};
>> +
>> +		sdhci@f9824900 {
>> +			bus-width = <8>;
>> +			non-removable;
>> +			status = "okay";
>> +		};
>> +
>> +		sdhci@f98a4900 {
>> +			cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
>> +			bus-width = <4>;
>> +		};
>> +	};
>> +};
>> diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
>> index 21d01e5..1f130bc 100644
>> --- a/arch/arm/boot/dts/qcom-apq8084.dtsi
>> +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
>> @@ -3,6 +3,7 @@
>> #include "skeleton.dtsi"
>> 
>> #include <dt-bindings/clock/qcom,gcc-apq8084.h>
>> +#include <dt-bindings/gpio/gpio.h>
>> 
>> / {
>> 	model = "Qualcomm APQ 8084";
>> @@ -203,5 +204,27 @@
>> 			clock-names = "core", "iface";
>> 			status = "disabled";
>> 		};
>> +
>> +		sdhci@f9824900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
>> +			reg-names = "hc_mem", "core_mem";
>> +			interrupts = <0 123 0>, <0 138 0>;
> 
> I see that you've used GPIO_ACTIVE_* above. Is the trailing zero here
> possibly IRQ_TYPE_NONE?
> 
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			status = "disabled";
>> +		};
>> +
>> +		sdhci@f98a4900 {
>> +			compatible = "qcom,sdhci-msm-v4";
>> +			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
>> +			reg-names = "hc_mem", "core_mem";
>> +			interrupts = <0 125 0>, <0 221 0>;
>> +			interrupt-names = "hc_irq", "pwr_irq";
>> +			clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
>> +			clock-names = "core", "iface";
>> +			status = "disabled";
>> +		};
> 
> If you assign labels to these two nodes, you can reference them in the
> .dts as &labelname {...};. Same for the uart node. That avoids
> duplicating the hierarchy, detects spelling mistakes at compile time and
> reduces indentation. Cf. the recent ifc6410 patch.

Got no issues with introducing the labels, but I’d like to keep the hierarchy in the .dts file.

> Also, is sdhci the best node name here? Usually it's not supposed to
> reflect the exact interface used (e.g., usb vs. ehci).

probably just use sdhc

> 
>> 	};
>> };
> 
> Otherwise looks good.
> 
> Regards,
> Andreas
> 
> -- 
> SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
> GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

-- 
Employee of Qualcomm Innovation Center, Inc.
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [Linux for Sparc]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux MIPS]     [ECOS]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux