Hi,
Am 03.09.2014 18:50, schrieb Georgi Djakov:
> Add basic support for the IFC6540 single-board computer boards, that are
> based on the APQ8084 SoC. This patch adds the initial device tree and the
> neccessary nodes required for enabling the serial port and eMMC.
>
> Signed-off-by: Georgi Djakov <gdjakov@xxxxxxxxxx>
> ---
> Changes since v2:
> - Squashed all patches into one. (suggested by Kumar Gala)
>
> Changes since v1:
> - This time add linux-arm-msm list to the CC.
> - Include a third patch for enabling the eMMC.
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/qcom-apq8084-ifc6540.dts | 23 +++++++++++++++++++++++
> arch/arm/boot/dts/qcom-apq8084.dtsi | 23 +++++++++++++++++++++++
> 3 files changed, 47 insertions(+)
> create mode 100644 arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b022972..df8453a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -345,6 +345,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
> dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-apq8064-ifc6410.dtb \
> qcom-apq8074-dragonboard.dtb \
> + qcom-apq8084-ifc6540.dtb \
> qcom-apq8084-mtp.dtb \
> qcom-msm8660-surf.dtb \
> qcom-msm8960-cdp.dtb
> diff --git a/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
> new file mode 100644
> index 0000000..c9ff108
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-apq8084-ifc6540.dts
> @@ -0,0 +1,23 @@
> +#include "qcom-apq8084.dtsi"
> +
> +/ {
> + model = "Qualcomm APQ8084/IFC6540";
> + compatible = "qcom,apq8084-ifc6540", "qcom,apq8084";
> +
> + soc {
> + serial@f995e000 {
> + status = "okay";
> + };
> +
> + sdhci@f9824900 {
> + bus-width = <8>;
> + non-removable;
> + status = "okay";
> + };
> +
> + sdhci@f98a4900 {
> + cd-gpios = <&tlmm 122 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
> index 21d01e5..1f130bc 100644
> --- a/arch/arm/boot/dts/qcom-apq8084.dtsi
> +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
> @@ -3,6 +3,7 @@
> #include "skeleton.dtsi"
>
> #include <dt-bindings/clock/qcom,gcc-apq8084.h>
> +#include <dt-bindings/gpio/gpio.h>
>
> / {
> model = "Qualcomm APQ 8084";
> @@ -203,5 +204,27 @@
> clock-names = "core", "iface";
> status = "disabled";
> };
> +
> + sdhci@f9824900 {
> + compatible = "qcom,sdhci-msm-v4";
> + reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
> + reg-names = "hc_mem", "core_mem";
> + interrupts = <0 123 0>, <0 138 0>;
I see that you've used GPIO_ACTIVE_* above. Is the trailing zero here
possibly IRQ_TYPE_NONE?
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
> + };
> +
> + sdhci@f98a4900 {
> + compatible = "qcom,sdhci-msm-v4";
> + reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
> + reg-names = "hc_mem", "core_mem";
> + interrupts = <0 125 0>, <0 221 0>;
> + interrupt-names = "hc_irq", "pwr_irq";
> + clocks = <&gcc GCC_SDCC2_APPS_CLK>, <&gcc GCC_SDCC2_AHB_CLK>;
> + clock-names = "core", "iface";
> + status = "disabled";
> + };
If you assign labels to these two nodes, you can reference them in the
.dts as &labelname {...};. Same for the uart node. That avoids
duplicating the hierarchy, detects spelling mistakes at compile time and
reduces indentation. Cf. the recent ifc6410 patch.
Also, is sdhci the best node name here? Usually it's not supposed to
reflect the exact interface used (e.g., usb vs. ehci).
> };
> };
Otherwise looks good.
Regards,
Andreas
--
SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Jeff Hawn, Jennifer Guild, Felix Imendörffer; HRB 16746 AG Nürnberg
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
