Add a PHY driver for uses with AHCI based SATA controller driver on the
APQ8064 family of SoCs.
This patch is a forward port from Qualcomm's v3.4 andriod kernel.
Tested on IFC6410 board.
CC: Sujit Reddy Thumma <sthumma@xxxxxxxxxxxxxx>
Tested-by: Kiran Padwal <kiran.padwal@xxxxxxxxxxxxxxx>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@xxxxxxxxxx>
---
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-apq8064-sata.c | 288 ++++++++++++++++++++++++++++++++++++
3 files changed, 296 insertions(+)
create mode 100644 drivers/phy/phy-qcom-apq8064-sata.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index 5fceb33..e22b1d1 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -188,4 +188,11 @@ config PHY_XGENE
help
This option enables support for APM X-Gene SoC multi-purpose PHY.
+config PHY_QCOM_APQ8064_SATA
+ tristate "Qualcomm APQ8064 SATA SerDes/PHY driver"
+ depends on ARCH_QCOM
+ depends on HAS_IOMEM
+ depends on OF
+ select GENERIC_PHY
+
endmenu
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 54f04d0..a4819d3 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -21,3 +21,4 @@ phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o
phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
+obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
diff --git a/drivers/phy/phy-qcom-apq8064-sata.c b/drivers/phy/phy-qcom-apq8064-sata.c
new file mode 100644
index 0000000..c9b4dd6
--- /dev/null
+++ b/drivers/phy/phy-qcom-apq8064-sata.c
@@ -0,0 +1,288 @@
+/*
+ * Copyright (c) 2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/time.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+/* PHY registers */
+#define UNIPHY_PLL_REFCLK_CFG 0x000
+#define UNIPHY_PLL_PWRGEN_CFG 0x014
+#define UNIPHY_PLL_GLB_CFG 0x020
+#define UNIPHY_PLL_SDM_CFG0 0x038
+#define UNIPHY_PLL_SDM_CFG1 0x03C
+#define UNIPHY_PLL_SDM_CFG2 0x040
+#define UNIPHY_PLL_SDM_CFG3 0x044
+#define UNIPHY_PLL_SDM_CFG4 0x048
+#define UNIPHY_PLL_SSC_CFG0 0x04C
+#define UNIPHY_PLL_SSC_CFG1 0x050
+#define UNIPHY_PLL_SSC_CFG2 0x054
+#define UNIPHY_PLL_SSC_CFG3 0x058
+#define UNIPHY_PLL_LKDET_CFG0 0x05C
+#define UNIPHY_PLL_LKDET_CFG1 0x060
+#define UNIPHY_PLL_LKDET_CFG2 0x064
+#define UNIPHY_PLL_CAL_CFG0 0x06C
+#define UNIPHY_PLL_CAL_CFG8 0x08C
+#define UNIPHY_PLL_CAL_CFG9 0x090
+#define UNIPHY_PLL_CAL_CFG10 0x094
+#define UNIPHY_PLL_CAL_CFG11 0x098
+#define UNIPHY_PLL_STATUS 0x0C0
+
+#define SATA_PHY_SER_CTRL 0x100
+#define SATA_PHY_TX_DRIV_CTRL0 0x104
+#define SATA_PHY_TX_DRIV_CTRL1 0x108
+#define SATA_PHY_TX_IMCAL0 0x11C
+#define SATA_PHY_TX_IMCAL2 0x124
+#define SATA_PHY_RX_IMCAL0 0x128
+#define SATA_PHY_EQUAL 0x13C
+#define SATA_PHY_OOB_TERM 0x144
+#define SATA_PHY_CDR_CTRL0 0x148
+#define SATA_PHY_CDR_CTRL1 0x14C
+#define SATA_PHY_CDR_CTRL2 0x150
+#define SATA_PHY_CDR_CTRL3 0x154
+#define SATA_PHY_PI_CTRL0 0x168
+#define SATA_PHY_POW_DWN_CTRL0 0x180
+#define SATA_PHY_POW_DWN_CTRL1 0x184
+#define SATA_PHY_TX_DATA_CTRL 0x188
+#define SATA_PHY_ALIGNP 0x1A4
+#define SATA_PHY_TX_IMCAL_STAT 0x1E4
+#define SATA_PHY_RX_IMCAL_STAT 0x1E8
+
+#define UNIPHY_PLL_LOCK BIT(0)
+#define SATA_PHY_TX_CAL BIT(0)
+#define SATA_PHY_RX_CAL BIT(0)
+
+/* default timeout set to 1 sec */
+#define TIMEOUT_MS 10000
+#define DELAY_INTERVAL_US 100
+
+struct qcom_apq8064_sata_phy {
+ void __iomem *mmio;
+ struct clk *cfg_clk;
+ struct device *dev;
+};
+
+/* Helper function to do poll and timeout */
+static int read_poll_timeout(void __iomem *addr, u32 mask)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(TIMEOUT_MS);
+
+ do {
+ if (readl_relaxed(addr) & mask)
+ return 0;
+
+ usleep_range(DELAY_INTERVAL_US, DELAY_INTERVAL_US + 50);
+ } while (!time_after(jiffies, timeout));
+
+ return -ETIMEDOUT;
+}
+
+static int qcom_apq8064_sata_phy_init(struct phy *generic_phy)
+{
+ struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
+ void __iomem *base = phy->mmio;
+ int ret = 0;
+
+ /* SATA phy initialization */
+ writel_relaxed(0x01, base + SATA_PHY_SER_CTRL);
+ writel_relaxed(0xB1, base + SATA_PHY_POW_DWN_CTRL0);
+ /* Make sure the power down happens before power up */
+ mb();
+ usleep_range(10, 60);
+
+ writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
+ writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
+ writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
+ writel_relaxed(0x02, base + SATA_PHY_TX_IMCAL2);
+
+ /* Write UNIPHYPLL registers to configure PLL */
+ writel_relaxed(0x04, base + UNIPHY_PLL_REFCLK_CFG);
+ writel_relaxed(0x00, base + UNIPHY_PLL_PWRGEN_CFG);
+
+ writel_relaxed(0x0A, base + UNIPHY_PLL_CAL_CFG0);
+ writel_relaxed(0xF3, base + UNIPHY_PLL_CAL_CFG8);
+ writel_relaxed(0x01, base + UNIPHY_PLL_CAL_CFG9);
+ writel_relaxed(0xED, base + UNIPHY_PLL_CAL_CFG10);
+ writel_relaxed(0x02, base + UNIPHY_PLL_CAL_CFG11);
+
+ writel_relaxed(0x36, base + UNIPHY_PLL_SDM_CFG0);
+ writel_relaxed(0x0D, base + UNIPHY_PLL_SDM_CFG1);
+ writel_relaxed(0xA3, base + UNIPHY_PLL_SDM_CFG2);
+ writel_relaxed(0xF0, base + UNIPHY_PLL_SDM_CFG3);
+ writel_relaxed(0x00, base + UNIPHY_PLL_SDM_CFG4);
+
+ writel_relaxed(0x19, base + UNIPHY_PLL_SSC_CFG0);
+ writel_relaxed(0xE1, base + UNIPHY_PLL_SSC_CFG1);
+ writel_relaxed(0x00, base + UNIPHY_PLL_SSC_CFG2);
+ writel_relaxed(0x11, base + UNIPHY_PLL_SSC_CFG3);
+
+ writel_relaxed(0x04, base + UNIPHY_PLL_LKDET_CFG0);
+ writel_relaxed(0xFF, base + UNIPHY_PLL_LKDET_CFG1);
+
+ writel_relaxed(0x02, base + UNIPHY_PLL_GLB_CFG);
+ /* make sure global config LDO power down happens before power up */
+ mb();
+
+ writel_relaxed(0x03, base + UNIPHY_PLL_GLB_CFG);
+ writel_relaxed(0x05, base + UNIPHY_PLL_LKDET_CFG2);
+
+ /* PLL Lock wait */
+ ret = read_poll_timeout(base + UNIPHY_PLL_STATUS, UNIPHY_PLL_LOCK);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout UNIPHY_PLL_STATUS\n");
+ return ret;
+ }
+
+ /* TX Calibration */
+ ret = read_poll_timeout(base + SATA_PHY_TX_IMCAL_STAT, SATA_PHY_TX_CAL);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout SATA_PHY_TX_IMCAL_STAT\n");
+ return ret;
+ }
+
+ /* RX Calibration */
+ ret = read_poll_timeout(base + SATA_PHY_RX_IMCAL_STAT, SATA_PHY_RX_CAL);
+ if (ret) {
+ dev_err(phy->dev, "poll timeout SATA_PHY_RX_IMCAL_STAT\n");
+ return ret;
+ }
+
+ /* SATA phy calibrated succesfully, power up to functional mode */
+ writel_relaxed(0x3E, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x01, base + SATA_PHY_RX_IMCAL0);
+ writel_relaxed(0x01, base + SATA_PHY_TX_IMCAL0);
+
+ writel_relaxed(0x00, base + SATA_PHY_POW_DWN_CTRL1);
+ writel_relaxed(0x59, base + SATA_PHY_CDR_CTRL0);
+ writel_relaxed(0x04, base + SATA_PHY_CDR_CTRL1);
+ writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL2);
+ writel_relaxed(0x00, base + SATA_PHY_PI_CTRL0);
+ writel_relaxed(0x00, base + SATA_PHY_CDR_CTRL3);
+ writel_relaxed(0x01, base + SATA_PHY_POW_DWN_CTRL0);
+
+ writel_relaxed(0x11, base + SATA_PHY_TX_DATA_CTRL);
+ writel_relaxed(0x43, base + SATA_PHY_ALIGNP);
+ writel_relaxed(0x04, base + SATA_PHY_OOB_TERM);
+
+ writel_relaxed(0x01, base + SATA_PHY_EQUAL);
+ writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL0);
+ writel_relaxed(0x09, base + SATA_PHY_TX_DRIV_CTRL1);
+
+ return 0;
+}
+
+static int qcom_apq8064_sata_phy_exit(struct phy *generic_phy)
+{
+ struct qcom_apq8064_sata_phy *phy = phy_get_drvdata(generic_phy);
+ void __iomem *base = phy->mmio;
+
+ /* Power down PHY */
+ writel_relaxed(0xF8, base + SATA_PHY_POW_DWN_CTRL0);
+ writel_relaxed(0xFE, base + SATA_PHY_POW_DWN_CTRL1);
+
+ /* Power down PLL block */
+ writel_relaxed(0x00, base + UNIPHY_PLL_GLB_CFG);
+
+ return 0;
+}
+
+static struct phy_ops qcom_apq8064_sata_phy_ops = {
+ .init = qcom_apq8064_sata_phy_init,
+ .exit = qcom_apq8064_sata_phy_exit,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_apq8064_sata_phy_probe(struct platform_device *pdev)
+{
+ struct qcom_apq8064_sata_phy *phy;
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct phy_provider *phy_provider;
+ struct phy *generic_phy;
+ int ret;
+
+ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ phy->mmio = devm_ioremap_resource(dev, res);
+ if (IS_ERR(phy->mmio))
+ return PTR_ERR(phy->mmio);
+
+ generic_phy = devm_phy_create(dev, &qcom_apq8064_sata_phy_ops, NULL);
+ if (IS_ERR(generic_phy)) {
+ dev_err(dev, "%s: failed to create phy\n", __func__);
+ return PTR_ERR(generic_phy);
+ }
+
+ phy->dev = dev;
+ phy_set_drvdata(generic_phy, phy);
+ platform_set_drvdata(pdev, phy);
+
+ phy->cfg_clk = devm_clk_get(dev, "cfg");
+ if (IS_ERR(phy->cfg_clk)) {
+ dev_err(dev, "Failed to get sata cfg clock\n");
+ return PTR_ERR(phy->cfg_clk);
+ }
+
+ ret = clk_prepare_enable(phy->cfg_clk);
+ if (ret)
+ return ret;
+
+ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+ if (IS_ERR(phy_provider)) {
+ clk_disable_unprepare(phy->cfg_clk);
+ dev_err(dev, "%s: failed to register phy\n", __func__);
+ return PTR_ERR(phy_provider);
+ }
+
+ return 0;
+}
+
+static int qcom_apq8064_sata_phy_remove(struct platform_device *pdev)
+{
+ struct qcom_apq8064_sata_phy *phy = platform_get_drvdata(pdev);
+
+ clk_disable_unprepare(phy->cfg_clk);
+
+ return 0;
+}
+
+static const struct of_device_id qcom_apq8064_sata_phy_of_match[] = {
+ { .compatible = "qcom,apq8064-sata-phy" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, qcom_apq8064_sata_phy_of_match);
+
+static struct platform_driver qcom_apq8064_sata_phy_driver = {
+ .probe = qcom_apq8064_sata_phy_probe,
+ .remove = qcom_apq8064_sata_phy_remove,
+ .driver = {
+ .name = "qcom-apq8064-sata-phy",
+ .owner = THIS_MODULE,
+ .of_match_table = qcom_apq8064_sata_phy_of_match,
+ }
+};
+module_platform_driver(qcom_apq8064_sata_phy_driver);
+
+MODULE_DESCRIPTION("QCOM apq8064 SATA PHY driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-arm-msm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
