This patch series extends the driver to also support bq24250/bq24251. The bq24250/251/257 devices have a very similar feature set and are virtually identical from a control register point of view so it made sense to extend the existing driver rather than submitting a new driver. In addition to the new device support the driver is also extended to allow access to some device features previously hidden. Basic and potentially dangerous charger config parameters affecting the actual charging of the Li-Ion battery are only configurable through firmware rather than sysfs properties. However some newly introduced properties are exposed through sysfs properties as access to them may be desired from userspace. For example, it is now possible to manually configure the maximum current drawn from the input source to accommodate different chargers (0.5A, 1.5A, 2.0A and so on) based on system knowledge a userspace application may have rather than rely on the auto-detection mechanism that may not work in all possible scenarios. Note that most patches have dependencies on other patches in the series. v6: - Removed the ability to configure the IRQ through "stat-gpios" - Allow re-configuring the input_current_limit via sysfs also when charger auto-detection is enabled - Use gpiod interface for initialization as a platform device (nice GPIO setup simplification) - Document all newly introduced sysfs nodes - Streamlined/fixed/simplified charger state handling as it relates to battery removal/insertion and the associated handling of the input current limit setting - Minor simplifications/cleanup - Rebased onto git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux- power-supply.git (branch "next") and completely retested v5: - Added patch to use the managed version of power supply register which also fixes a code flow issue that was introduced - Minor fixes / consistency cleanup (Krzysztof's feedback) v4: - Removed configurability of the safety timer multiplier through DT v3: - Dropped the driver/symbol rename patch from v2 due to anticipated issues with upcoming bq2425x family additions - Reverted additional mutex coverage for I2C access due to regmap built-in mutex protection being sufficient - Removed support for trickle charging due to being a rare/uncommon use case - Fixed most checkpatch.pl --strict alignment issues (except where the line length would exceed 80 chars) - Fixed an issue with how the return value of gpio_to_desc() was handled - Fixed an issue with the definition of bq24257_of_match[] - Reordered the patch series to put the DT doc changes to the beginning v2: - Aligned DT bindings better with existing "ti,*" charger bindings - Dropped patch that improperly reported a missing battery as a dead battery - Fixed (hopefully, that is -- still waiting for my test platform) issue with how the private ACPI driver_data used to identify which bq2425x device to use - Removed boolean DT/ACPI properties mostly by replacing them with more intelligent handling in the driver - Rework/clarification of DT bindings doc - Renamed/refactored filenames/symbols from bq24257 to bq2425x to better reflect that multiple devices are covered. Despite initial hesitation I feel this is a good opportunity for some clean-up as the driver is still very new in the Kernel so the change should be low risk. This also addresses one of Andrew Davis' feedback items. Plus, it makes for a nice alignment with the existing bq2415x_charger driver. v1: - Initial submission Andreas Dannenberg (14): dt: power: bq24257-charger: Cover additional devices power: bq24257: Remove IRQ config through stat-gpios power: bq24257: Streamline input current limit setup power: bq24257: Add basic support for bq24250/bq24251 power: bq24257: Add bit definition for temp sense enable power: bq24257: Allow manual setting of input current limit power: bq24257: Add SW-based approach for Power Good determination power: bq24257: Use managed power supply register power: bq24257: Add over voltage protection setting support power: bq24257: Add input DPM voltage threshold setting support power: bq24257: Allow input current limit sysfs access power: bq24257: Add various device-specific sysfs properties power: bq24257: Add platform data based initialization Documentation: power: bq24257: Document exported sysfs entries Documentation/ABI/testing/sysfs-class-power | 58 +++ .../devicetree/bindings/power/bq24257.txt | 53 ++- drivers/power/Kconfig | 5 +- drivers/power/bq24257_charger.c | 516 ++++++++++++++++++--- include/linux/power/bq24257_charger.h | 25 + 5 files changed, 577 insertions(+), 80 deletions(-) create mode 100644 include/linux/power/bq24257_charger.h -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe linux-api" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
