I am told it’s analog. I don't know what the story with serial is any more than you do, thanks for the progress reports though. ~Andrew -----Original Message----- From: Philippe Vouters [mailto:philippe.vouters@xxxxxxxxxxx] Sent: Wednesday, July 04, 2012 2:08 PM To: Andrew Merczynski-Hait; Linmodems; Antonio Olivares; Marvin Stodolsky Subject: Still NO DIALTONE !!! Andrew, Still NO DIALTONE on efax command !!! Are you sure the phone line is connected ??? Is this an analog or digital phone line ? Philippe andrew@ubuntu-11:~$ uname -r 3.0.0-12-generic $ tar -zxvf ungrab-winmodem-20090716.tar.gz $ cd ungrab-winmodem-20090716/ $ make $ sudo make install $ lspci -vvv shows serial $ sudo modprobe ungrab-winmodem $ lspci -vvv 01:00.0 Modem: Intel Corporation FA82537EP 56K V.92 Data/Fax Modem PCI (rev 04) (prog-if 00 [Generic]) Subsystem: Dell Device 1000 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping+ SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 21 Region 0: Memory at feafe000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at de00 [size=256] Capabilities: <access denied> 01:02.0 Multimedia audio controller: Creative Labs CA0106 Soundblaster So the Intel 536EP board no longer shows serial. However, efax still shows NO DIALTONE. $ cd ../intel-536-537/ $ make 537 $ sudo make install $ cd $HOME/ andrew@ubuntu-11:~$ efax -o 1 -vewinchmart -t 2034258 efax: Wed Jul 4 13:48:41 2012 efax v 0.9a-001114 Copyright 1999 Ed Casas efax: Wed Jul 4 13:48:41 2012 efax v 0.9a-001114 Copyright 1999 Ed Casas efax: 48:41 compiled Jun 21 2006 05:59:09 efax: 48:41 argv[0]=efax efax: 48:41 argv[1]=-o efax: 48:41 argv[2]=1 efax: 48:41 argv[3]=-vewinchmart efax: 48:41 argv[4]=-t efax: 48:41 argv[5]=2034258 efax: 48:41 opened /dev/modem efax: 48:42 command "Q0V1" efax: 48:42 waiting 2.0 s efax: 48:42 .348 [ATQ0V1<CR><CR><LF>] efax: 48:42 .408 [OK<CR><LF>] efax: 48:42 response "OK" efax: 48:42 command "E0" efax: 48:42 waiting 5.0 s efax: 48:42 .528 [ATE0<CR><CR><LF>] efax: 48:42 .580 [OK<CR><LF>] efax: 48:42 response "OK" efax: 48:42 command "I3" efax: 48:42 waiting 5.0 s efax: 48:42 .728 [<CR><LF>537EP <CR><LF>] efax: 48:42 .748 [<CR><LF>OK<CR><LF>] efax: 48:42 response "OK" efax: 48:42 command "+FCLASS=1" efax: 48:42 waiting 5.0 s efax: 48:42 .920 [<CR><LF>OK<CR><LF>] efax: 48:42 response "OK" efax: 48:42 using 537EP in class 1 efax: 48:43 command "+FTM=?" efax: 48:43 waiting 5.0 s efax: 48:43 .068 [<CR><LF>24,48,72,73,74,96,97,98,121,122,145,146<CR><LF>] efax: 48:43 .088 [<CR><LF>OK<CR><LF>] efax: 48:43 response "OK" efax: 48:43 dialing 2034258 efax: 48:43 command "D2034258" efax: 48:43 waiting 120.0 s efax: 48:53 .340 [<CR><LF>NO DIALTONE<CR><LF>] efax: 48:53 response "NO DIALTONE" efax: 48:53 Error: dial command failed efax: 48:53 command "Q0V1" efax: 48:53 waiting 2.0 s efax: 48:53 .520 [<CR><LF>OK<CR><LF>] efax: 48:53 response "OK" efax: 48:53 command "H" efax: 48:53 waiting 5.0 s efax: 48:54 .380 [<CR><LF>OK<CR><LF>] efax: 48:54 response "OK" efax: 48:54 done, returning 2 (unrecoverable error)
