Antonio, thanks for the quick reply. Here is the output of wvdial [root@kitty ~]# wvdialconf /etc/wvdial.conf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S2 S3 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>. [root@kitty ~]# -----Original Message----- From: Antonio Olivares [mailto:olivares14031@xxxxxxxxx] Sent: Tuesday, July 03, 2012 4:15 PM To: Mike Cavanagh Cc: discuss@xxxxxxxxxxxxx Subject: Re: Mike C, USA, CentOS release 6.2 (Final) Kernel kernel 2.6.32-220.23.1.el6.x86_64 Mike, For one chipset hopefully it is a true serial modem, For candidate card in slot 00:03.3, firmware information and bootup diagnostics are: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:03.3 8086:2a07 17aa:20d4 Serial controller: Intel Corporation Mobile PM965/GM965 KT Controller Modem interrupt assignment and sharing: 17: 85 14 IO-APIC-fasteoi uhci_hcd:usb6, firewire_ohci --- Bootup diagnostics for card in PCI slot 00:03.3 ---- pci 0000:00:03.3: reg 10 io port: [0x1830-0x1837] pci 0000:00:03.3: reg 14 32bit mmio: [0xfe224000-0xfe224fff] serial 0000:00:03.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 0000:00:03.3: ttyS1 at I/O 0x1830 (irq = 17) is a 16550A Try the following as root: $ su - passwd: # wvdialconf /etc/wvdial.conf let it run and send us the information that it outputs. Hopefully it finds /dev/ttyS1 as the modem port, and all that would remain is to configure wvdial.conf with ISP phone number, username, and password and attempt to connect with # wvdial Please send list(discuss@xxxxxxxxxxxxx) the output of wvdialconf /etc/wvdial.conf Regards, Antonio On Tue, Jul 3, 2012 at 5:38 PM, Mike Cavanagh <mike@xxxxxxxxxxxxxxxxxxx> wrote: > Sorry I do not understand this better, but I am not sure where to > start... > I have a Lenovo (IBM) Thinkpad X61s with an internal Intel modem > Looks like the modem Chipset is the PM965 > It is located in PCI slot 3.0 > > I can see the message: "pci 0000:00:03.0: PME# disabled" in the Dmesg, > but I am not sure if it is relevant. I assume it is. > > I assume I will need to find a driver, but no idea how to find it. > > Bsaed on the file below: > Does it appear I have a modem that can work or am I done at the > start? > If it can work, does it look like I just need the proper > configuration or do I need to compile drivers, etc.? > > Any help is much appreciated. > Please let me know if you need more information. > Thanks, > Mike C. > > > ModemData.Txt:------------------------- > > > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List > Server, > as HTML can contain viruses. Use as the email Subject Line: > YourName, YourCountry CentOS release 6.2 (Final) > Kernel kernel 2.6.32-220.23.1.el6.x86_64 > With this Subject Line cogent experts will be alerted, and useful case > names left in the Archive. > YourCountry will enable Country specific guidance. Linux experts in > YourCountry > can be found through: http://www.linux.org/groups/index.html. > They will know your Country's modem code, which may be essential for > dialup service. > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an > Internet Provider mail filters. > So in a day, also check the Archived responses at > http://www.linmodems.org > -------------------------- System information > ---------------------------- > CPU=x86_64, CentOS > Kernel , ALSA_version=1.0.21 > Linux version 2.6.32-220.23.1.el6.x86_64 > (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.6 20110731 (Red > Hat 4.4.6-3) (GCC) ) #1 SMP Mon Jun 18 18:58:52 BST 2012 > scanModem update of: 2011_08_08 > > /etc/lsb-release not found > > > Presently install your Linux Distributions dkms package. It provides for > automated driver updates, > following upgrade of your kernel. For details see > http://linux.dell.com/projects.shtml#dkms > > > Some modem drivers can only be used in 32 bit modem on x86_64 systems, > while some others are competent on x86_64 Systems. Cases are: > 1) http://linmodems.technion.ac.il/bigarch/archive-seventh/msg03119.html > > for the snd-hda-intel audio+modem driver. Also applicable to AC97 modem > controllers. > In both cases, 32 bit libraries must be installed to support the > slmodemd helper having a precompiled 32 bit component. > 2) For USB modems using the slusb.ko driver. 32 bit libraries must be > installed to support the slmodemd helper having a precompiled 32 bit > component > 3) The hsfmodem and hcfpcimodem drivers for Conexant chipsest modes are > x86_64 competent. > 4) agrsm packages for LSI/AgereSystems softmodems are not competent on > x86_64 systems. > > There are no blacklisted modem drivers in /etc/modprobe* files > > Potentially useful modem drivers now loaded are: > snd_hda_intel > > Attached USB devices are: > ID 17ef:1000 Lenovo > ID 0a5c:2110 Broadcom Corp. Bluetooth Controller > ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader > ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub > ID 058f:9254 Alcor Micro Corp. Hub > ID 04b4:2324 Cypress Semiconductor Corp. > ID 045e:0040 Microsoft Corp. Wheel Mouse Optical > ID 0aec:3260 Neodio Technologies Corp. 7-in-1 Card Reader > ID 06e1:d804 ADS Technologies, Inc. > ID 8086:0630 Intel Corp. Pocket PC Camera > If a cellphone is not detected, see > http://ubuntuforums.org/archive/index.php/t-878554.html > A sample report is: > http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html > > If a USB modem or cellphone is attached and was not detected, please > provide available information in your request to discuss@xxxxxxxxxxxxx > > Candidate PCI devices with modem chips are: > 00:03.0 Communication controller: Intel Corporation Mobile PM965/GM965 > MEI Controller (rev 0c) > 00:03.3 Serial controller: Intel Corporation Mobile PM965/GM965 KT > Controller (rev 0c) > 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio > Controller (rev 03) > High Definition Audio cards can host modem chips. > > For candidate card in slot 00:03.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:03.0 8086:2a04 17aa:20d1 Communication > controller: Intel Corporation Mobile PM965/GM965 MEI Controller > > Modem interrupt assignment and sharing: > --- Bootup diagnostics for card in PCI slot 00:03.0 ---- > pci 0000:00:03.0: reg 10 64bit mmio: [0xfe226000-0xfe22600f] > pci 0000:00:03.0: PME# supported from D0 D3hot D3cold > pci 0000:00:03.0: PME# disabled > pci 0000:03:00.0: reg 10 64bit mmio: [0xfdf00000-0xfdf01fff] > pci 0000:03:00.0: PME# supported from D0 D3hot D3collsd > pci 0000:03:00.0: PME# disabled > iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 > iwlagn 0000:03:00.0: setting latency timer to 64 > iwlagn 0000:03:00.0: Detected Intel(R) Wireless WiFi Link 4965AGN, > REV=0x4 > iwlagn 0000:03:00.0: device EEPROM VER=0x36, CALIB=0x5 > iwlagn 0000:03:00.0: Tunable channels: 11 802.11bg, 13 802.11a channels > iwlagn 0000:03:00.0: irq 29 for MSI/MSI-X > iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode > iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 > > The PCI slot 00:03.0 of the modem card may be disabled early in > a bootup process, but then enabled later. If modem drivers load > but the modem is not responsive, read DOCs/Bootup.txt about possible > fixes. > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx > if help is needed. > > > For candidate card in slot 00:03.3, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:03.3 8086:2a07 17aa:20d4 Serial controller: Intel > Corporation Mobile PM965/GM965 KT Controller > > Modem interrupt assignment and sharing: > 17: 85 14 IO-APIC-fasteoi uhci_hcd:usb6, > firewire_ohci > --- Bootup diagnostics for card in PCI slot 00:03.3 ---- > pci 0000:00:03.3: reg 10 io port: [0x1830-0x1837] > pci 0000:00:03.3: reg 14 32bit mmio: [0xfe224000-0xfe224fff] > serial 0000:00:03.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 > 0000:00:03.3: ttyS1 at I/O 0x1830 (irq = 17) is a 16550A > > For candidate card in slot 00:1b.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:1b.0 8086:284b 17aa:20ac Audio device: Intel > Corporation 82801H > > Modem interrupt assignment and sharing: > 28: 1649 288 PCI-MSI-edge hda_intel > --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- > pci 0000:00:1b.0: reg 10 64bit mmio: [0xfe220000-0xfe223fff] > pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold > pci 0000:00:1b.0: PME# disabled > HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17 > HDA Intel 0000:00:1b.0: irq 28 for MSI/MSI-X > HDA Intel 0000:00:1b.0: setting latency timer to 64 > > The PCI slot 00:1b.0 of the modem card may be disabled early in > a bootup process, but then enabled later. If modem drivers load > but the modem is not responsive, read DOCs/Bootup.txt about possible > fixes. > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx > if help is needed. > > > > ===== Advanced Linux Sound Architecture (ALSA) diagnostics ===== > The ALSA packages provide audio support and also drivers for some > modems. > ALSA diagnostics are written during bootup to /proc/asound/ folders. > > The modem cards detected by "aplay -l" are: None > > > The /proc/asound/pcm file reports: > ----------------------- > 00-00: AD198x Analog : AD198x Analog : playback 1 : capture 2 > 00-01: AD198x Digital : AD198x Digital : playback 1 > > about /proc/asound/cards: > ------------------------ > 0 [Intel ]: HDA-Intel - HDA Intel > HDA Intel at 0xfe220000 irq 28 > > PCI slot 00:1b.0 has a High Definition Audio Card > The drivers are in the kernel modules tree at: > > /lib/modules/2.6.32-220.el6.x86_64/kernel/sound/pci/hda/snd-hda-intel.ko > /lib/modules/2.6.32-220.17.1.el6.x86_64/kernel/sound/pci/hda/snd-hda-int > el.ko > /lib/modules/2.6.32-220.23.1.el6.x86_64/kernel/sound/pci/hda/snd-hda-int > el.ko > > The HDA diagnostics did not recognize a modem chip on the audio > subsystem, > though a Conexant chip modem might not be recognized. > > === Finished firmware and bootup diagnostics, next deducing cogent > software. === > > Predictive diagnostics for card in bus 00:03.3: > Modem chipset detected on > NAME="Serial controller: Intel Corporation Mobile PM965/GM965 KT > Controller " > CLASS=0700 > PCIDEV=8086:2a07 > SUBSYS=17aa:20d4 > IRQ=17 > SOFT=8086:2a07.MC97 > IDENT=mc97 > > For candidate modem in: 00:03.3 > 0700 Serial controller: Intel Corporation Mobile PM965/GM965 KT > Controller > Primary device ID: 8086:2a07 > Subsystem PCI_id 17aa:20d4 > Softmodem codec or chipset from diagnostics: > from Archives: > > > > > The soft modem is in the ac97/mc97 category. However the diagnostics > were not effective, > and an archival record for is lacking for the modem codec of pair: > 8086:2a07 17aa:20d4 > Try to acquire more information by running the modem diagnostics under a > Microsoft boot, > as described in SoftModem.txt > > > Writing DOCs/Intel.txt > > > Predictive diagnostics for card in bus 00:03.0: > Modem chipset not detected on > NAME="Communication controller: Intel Corporation Mobile PM965/GM965 MEI > Controller " > CLASS=0780 > PCIDEV=8086:2a04 > SUBSYS=17aa:20d1 > IRQ=10 > HDA2=00:1b.0 > > For candidate modem in: 00:03.0 > 0780 Communication controller: Intel Corporation Mobile PM965/GM965 > MEI Controller > Primary device ID: 8086:2a04 > Support type needed or chipset: > > > > Predictive diagnostics for card in bus 00:1b.0: > Modem chipset not detected on > NAME="Audio device: Intel Corporation 82801H " > CLASS=0403 > PCIDEV=8086:284b > SUBSYS=17aa:20ac > IRQ=28 > > For candidate modem in: 00:1b.0 > 0403 Audio device: Intel Corporation 82801H > Primary device ID: 8086:284b > Support type needed or chipset: > > > Completed candidate modem analyses. > > The base of the UDEV device file system is: /dev/.udev > > Versions adequately match for the compiler installed: 4.4.6 > and the compiler used in kernel assembly: 4.4.6 > > > > Minimal compiling resources appear complete: > make utility - /usr/bin/make > Compiler version 4.4 > linuc_headers base folder > /lib/modules/2.6.32-220.23.1.el6.x86_64/build > > However some compilations and executable functions may need additional > files, > in the FileNames.h (so called kernel "h"eaders) collection installed in > /usr/include/ . > For martian_modem, additional required packages are needed. The also > required headers of package libc6 are commonly installed by default. > Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev > packages, for kernels 2.6.24 and later versions. > In not included on your install CD, search for them at > http://packages.ubuntu.com > or comparable Repository for other Linux distros. > When compiling ALSA drivers, the utility "patch" will also be needed. > > > > > If a driver compilation fails, with message including some lack of some > FileName.h (stdio.h for example), then > Some additional kernel-header files need installation to /usr/include. > The minimal additional packages are libc6-dev > and any of its dependents, under Ubuntu linux-libc-dev > > If an alternate ethernet connection is available, > $ apt-get update > $ apt-get -s install linux-kernel-devel > will install needed packages. > For Debian/Ubuntu related distributions, run the following command to > display the needed package list: > > Otherwise packages have to be found through http://packages.ubuntu.com > Once downloaded and transferred into a Linux partition, > they can be installed alltogether with: > $ sudo dpkg -i *.deb > > > Checking pppd properties: > -r-xr-xr-x. 1 root root 359592 Aug 22 2010 /usr/sbin/pppd > > In case of an "error 17" "serial loopback" problem, see: > > http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html > > To enable dialout without Root permission do: > $ su - root (not for Ubuntu) > chmod a+x /usr/sbin/pppd > or under Ubuntu related Linuxes > chmod a+x /usr/sbin/pppd > > Checking settings of: /etc/ppp/options > lock > > In case of a message like: > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > For guidance on FAX usage, get from > http://linmodems.technion.ac.il/packages/ get faxing.tar.gz > It has samples for a modem using port /dev/ttySL0, which must be changed > to match your modem's port. > > Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 > virbr0 wlan0 > Which can interfere with Browser naviagation. > > Don't worry about the following, it is for experts should trouble > shooting be necessary. > ========================================================== > > Checking for modem support lines: > -------------------------------------- > /device/modem symbolic link: > slmodemd created symbolic link /dev/ttySL0: > Within /etc/udev/ files: > > Within /etc/modprobe.conf files: > > Within any ancient /etc/devfs files: > > Within ancient kernel 2.4.n /etc/module.conf files: > > --------- end modem support lines -------- > > >