The bios has no option for a disabled pnp. I have added the drivers
to the blacklisted file as you suggested although it still apears as
disabled in dmesg.txt.
On 28 May 2010 13:40, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote:
> Craig,
>
> If you can access the bootup BIOS, try switching to the non-PNP mode,
>
> Also among the drivers, these
> ppdev
> lp
> parport
> floppy
> are probably non-essential and might be unloaded or blacklisted to
> free up resources.
>
> MarvS
>
>
>
> On Fri, May 28, 2010 at 8:16 AM, Craig McLaren <craigmc@xxxxxxxxxxxxx> wrote:
>> So far in a attempt at resolving the resource conflict I've tried the
>> following:-
>>
>> used the pollirq and pci=routeirq kernal bootup options
>> downgraded to ubuntu 9.10
>> disabled usb controller in bios
>> tried different slots on motherboard
>>
>> Attached are the most recent ModemData, dmesg.txt files.
>>
>> On 27 May 2010 23:32, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote:
>>> Craig
>>>
>>> The most outstanding problem is:
>>>
>>> Modem interrupt assignment and sharing:
>>> 16: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
>>> --- Bootup diagnostics for card in PCI slot 04:00.0 ----
>>> [ 0.567384] pci 0000:04:00.0: reg 10 32bit mmio: [0xfe5ffc00-0xfe5fffff]
>>> [ 1.915516] serial 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
>>> [ 1.915521] serial 0000:04:00.0: PCI INT A disabled
>>>
>>> Enablement of the PCI slot 04:00.0 is necessary before there can be responses.
>>>
>>> There is resource competition from USB devices.
>>> Detach them before bootup and again try
>>> $ sudo wvdialconf
>>>
>>> Also read the BootUp.txt
>>>
>>> Please send to the List, not direct to me.
>>>
>>> MarvS
>>>
>>>
>>> On Thu, May 27, 2010 at 9:03 AM, Craig McLaren <craigmc35@xxxxxxxxxxxxxx> wrote:
>>>> Hi Marvin,
>>>>
>>>> wvdialconf failed with the output below:
>>>>
>>>> Editing `/etc/wvdial.conf'.
>>>>
>>>> Scanning your serial ports for a modem.
>>>>
>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>>>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>>> Modem Port Scan<*1>: S1 S2 S3
>>>>
>>>>
>>>> Sorry, no modem was detected! Is it in use by another program?
>>>> Did you configure it properly with setserial?
>>>>
>>>> Please read the FAQ at http://open.nit.ca/wiki/?WvDial
>>>>
>>>> If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>.
>>>>
>>>>
>>>> On 27 May 2010 13:42, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote:
>>>>> Craig,
>>>>>
>>>>> See if it is detected by wvdialconf:
>>>>> $ sudo wvdialconf
>>>>>
>>>>> MarvS
>>>>>
>>>>> On Thu, May 27, 2010 at 8:14 AM, Craig McLaren <craigmc35@xxxxxxxxxxxxxx> wrote:
>>>>>> Hello All, Please can someone advise what steps are necessary to get
>>>>>> the USR802981-OEM modem working. I have two of these which I plan on
>>>>>> using with Hylafax if they ever work. At the moment the serial port
>>>>>> does not appear to have been created although the device is listed
>>>>>> when I run lspci. I'm assuming they are compatible with Linux in some
>>>>>> way as this is what it says on USR website:-
>>>>>>
>>>>>> http://www.usr.com/support/product-template.asp?prod=oem#2980
>>>>>>
>>>>>> Any help greatly appreciated.
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Regards,
>>>>>>
>>>>>> Craig.
>>>>>>
>>>>>
>>>>
>>>>
>>>>
>>>> --
>>>> Regards,
>>>>
>>>> Craig.
>>>>
>>>
>>
>>
>>
>> --
>> Regards,
>>
>> Craig.
>>
>
--
Regards,
Craig.
Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry kernel 2.6.31-21-generic
With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
YourCountry will enable Country specific guidance. Linux experts in YourCountry
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686, Ubuntu , ALSA_version=
Linux version 2.6.31-21-generic (buildd@rothera) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu9) ) #59-Ubuntu SMP Wed Mar 24 07:28:56 UTC 2010
scanModem update of: 2010_04_29
Distrib_ID=Ubuntu
DistribCodeName=karmic
AptRepositoryStem=http://gb.archive.ubuntu.com/ubuntu/
The dkms driver upgrade utilities are installed,
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx
Candidate PCI devices with modem chips are:
04:00.0 Serial controller: U.S. Robotics Device 0152 (rev 02)
04:02.0 Serial controller: U.S. Robotics Device 0152 (rev 02)
High Definition Audio cards can host modem chips.
For candidate card in slot 04:00.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
04:00.0 16ec:0152 13a8:0129 Serial controller: U.S. Robotics Device 0152
Modem interrupt assignment and sharing:
--- Bootup diagnostics for card in PCI slot 04:00.0 ----
[ 0.507775] pci 0000:04:00.0: reg 10 32bit mmio: [0xfe5ff800-0xfe5ffbff]
[ 1.200749] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.981009] serial 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.981073] serial 0000:04:00.0: PCI INT A disabled
The PCI slot 04:00.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
For candidate card in slot 04:02.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
04:02.0 16ec:0152 13a8:0129 Serial controller: U.S. Robotics Device 0152
Modem interrupt assignment and sharing:
--- Bootup diagnostics for card in PCI slot 04:02.0 ----
[ 0.507832] pci 0000:04:02.0: reg 10 32bit mmio: [0xfe5ffc00-0xfe5fffff]
[ 1.200816] pci 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.981136] serial 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.981199] serial 0000:04:02.0: PCI INT A disabled
The PCI slot 04:02.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
=== Finished firmware and bootup diagnostics, next deducing cogent software. ===
A candidate modem is not transparent among the PCI devices:
------------------------------------------------
00:02.0 VGA compatible controller: Intel Corporation 82Q963/Q965 Integrated Graphics Controller (rev 02)
00:02.1 Display controller: Intel Corporation 82Q963/Q965 Integrated Graphics Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801H (ICH8 Family) 4 port SATA IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
00:1f.5 IDE interface: Intel Corporation 82801H (ICH8 Family) 2 port SATA IDE Controller (rev 02)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5754 Gigabit Ethernet PCI Express (rev 02)
04:00.0 Serial controller: U.S. Robotics Device 0152 (rev 02)
04:02.0 Serial controller: U.S. Robotics Device 0152 (rev 02)
------------------------------------------------
with USB, bridge, and RAM devices not displayed.
If a High Definition Audio card is present, if might be hosted on the Subsystem.
If your modem is an
external USB type,
connected by an external serial cable,
or mounted internally on an ISA card,
then scanModem would not access it.
Try with Root permission
$ sudo wvdialconf /etc/wvdial.conf
to detect these modem types and some USB modems.
If the detection is successful, read the DOCs/wvdial.txt .
Edit the /etc/wvdial.conf with Root permission:
sudo gedit /etc/wvdial.conf
will be able to dial out with Root permission:
sudo wvdial
Many modems for which scanModem fails have Conexant chips.
From http://www.linuxant.com/drivers/modemident.php
get the ListModem tool, which will report on Conexant chipset modems
If the above tests fail, please provide any independent information available on your modem.
If an alternative boot into Microsoft windows can be done, do mouse
clicks on:
Start > Settings > Control Panel > Classical View (for Window XP) > System
> Hardware > Device Manager > Modems > Click on the + > Modem. Double click to
expand the graphic. Manufacturer information may be displayed. For example, CXT
stands for Conexant. Click the Diagnostics Tab. Record any hardware ID or vendor
and device information. From the Driver Details TAB, copy out the VENdor and DEVice information.
Next do the Query Modem and record the ATI specifications displayed such as:
ATI3 - Agere SoftModem Version 2.1.22
ATI5 - 2.1.22, AMR Intel MB, AC97 ID:SIL REV:0x27
Try to identify the modem setup file, with name perhaps MODEM.INF.
If may contain chipset Vendor informaton.
Predictive diagnostics for card in bus 04:00.0:
Modem chipset not detected on
NAME="Serial controller: U.S. Robotics Device 0152 "
CLASS=0700
PCIDEV=16ec:0152
SUBSYS=13a8:0129
IRQ=16
For candidate modem in: 04:00.0
0700 Serial controller: U.S. Robotics Device 0152
Primary device ID: 16ec:0152
Support type needed or chipset:
Predictive diagnostics for card in bus 04:02.0:
Modem chipset not detected on
NAME="Serial controller: U.S. Robotics Device 0152 "
CLASS=0700
PCIDEV=16ec:0152
SUBSYS=13a8:0129
IRQ=18
For candidate modem in: 04:02.0
0700 Serial controller: U.S. Robotics Device 0152
Primary device ID: 16ec:0152
Support type needed or chipset:
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.4.1
and the compiler used in kernel assembly: 4.4.1
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.4
linuc_headers base folder /lib/modules/2.6.31-21-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ .
For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 277352 2009-02-20 17:25 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
For guidance on FAX usage, get from http://linmodems.technion.ac.il/packages/ get faxing.tar.gz
It has samples for a modem using port /dev/ttySL0, which must be changed to match your modem's port.
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
CPU0 CPU1
0: 108 0 IO-APIC-edge timer
1: 2 0 IO-APIC-edge i8042
6: 5 0 IO-APIC-edge floppy
8: 1 0 IO-APIC-edge rtc0
9: 0 0 IO-APIC-fasteoi acpi
12: 4 0 IO-APIC-edge i8042
20: 5628 0 IO-APIC-fasteoi ata_piix, ata_piix
27: 1 0 PCI-MSI-edge i915
28: 9776 0 PCI-MSI-edge eth0
NMI: 0 0 Non-maskable interrupts
LOC: 25720 20158 Local timer interrupts
SPU: 0 0 Spurious interrupts
CNT: 0 0 Performance counter interrupts
PND: 0 0 Performance pending work
RES: 35 28 Rescheduling interrupts
CAL: 28 48 Function call interrupts
TLB: 126 164 TLB shootdowns
TRM: 0 0 Thermal event interrupts
THR: 0 0 Threshold APIC interrupts
MCE: 0 0 Machine check exceptions
MCP: 16 16 Machine check polls
ERR: 1
MIS: 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.31-21-generic (buildd@rothera) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu9) ) #59-Ubuntu SMP Wed Mar 24 07:28:56 UTC 2010 (Ubuntu 2.6.31-21.59-generic)
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f5ffc00 (usable)
[ 0.000000] BIOS-e820: 000000003f5ffc00 - 000000003f601c00 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f603c00 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] DMI 2.3 present.
[ 0.000000] last_pfn = 0x3f5ff max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CBFFF write-protect
[ 0.000000] CC000-EFFFF uncachable
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask 000000000 write-back
[ 0.000000] 1 base 03F800000 mask FFF800000 uncachable
[ 0.000000] 2 base 03F700000 mask FFFF00000 uncachable
[ 0.000000] 3 base 040000000 mask FC0000000 uncachable
[ 0.000000] 4 base 080000000 mask F80000000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820 update range: 000000003f700000 - 0000000100000000 (usable) ==> (reserved)
[ 0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved)
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000002000 (usable)
[ 0.000000] modified: 0000000000002000 - 0000000000006000 (reserved)
[ 0.000000] modified: 0000000000006000 - 000000000009fc00 (usable)
[ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 000000003f5ffc00 (usable)
[ 0.000000] modified: 000000003f5ffc00 - 000000003f601c00 (ACPI NVS)
[ 0.000000] modified: 000000003f603c00 - 0000000040000000 (reserved)
[ 0.000000] modified: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fed00400 (reserved)
[ 0.000000] modified: 00000000fed20000 - 00000000feda0000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fef00000 (reserved)
[ 0.000000] modified: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] initial memory mapped : 0 - 00c00000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] Using x86 segment limits to approximate NX protection
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000
[ 0.000000] RAMDISK: 2f175000 - 2f8bfc38
[ 0.000000] ACPI: RSDP 000febf0 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 000fce97 0006C (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: FACP 000fcfbf 000F4 (v03 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: DSDT fff68958 0475F (v01 DELL dt_ex 00001000 INTL 20050624)
[ 0.000000] ACPI: FACS 3f5ffc00 00040
[ 0.000000] ACPI: SSDT fff6d1d6 000AA (v01 DELL st_ex 00001000 INTL 20050624)
[ 0.000000] ACPI: APIC 000fd0b3 00092 (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: BOOT 000fd145 00028 (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: ASF! 000fd16d 00092 (v32 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: MCFG 000fd1ff 0003E (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: HPET 000fd23d 00038 (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: TCPA 000fd499 00032 (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: SLIC 000fd275 00176 (v01 DELL B8K 00000014 ASL 00000061)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 126MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] node 0 low ram: 00000000 - 377fe000
[ 0.000000] node 0 bootmap 00008000 - 0000ef00
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00008ae160] TEXT DATA BSS ==> [0000100000 - 00008ae160]
[ 0.000000] #4 [002f175000 - 002f8bfc38] RAMDISK ==> [002f175000 - 002f8bfc38]
[ 0.000000] #5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
[ 0.000000] #6 [00008af000 - 00008b21a4] BRK ==> [00008af000 - 00008b21a4]
[ 0.000000] #7 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
[ 0.000000] #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000]
[ 0.000000] found SMP MP-table at [c00fe710] fe710
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0003f5ff
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00000002
[ 0.000000] 0: 0x00000006 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003f5ff
[ 0.000000] On node 0 totalpages: 259482
[ 0.000000] free_area_init_node: node 0, pgdat c0788d40, node_mem_map c1000000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3963 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 253 pages used for memmap
[ 0.000000] HighMem zone: 32004 pages, LIFO batch:7
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x05] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x02] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x03] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 8 CPUs, 6 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000f0000
[ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 40000000:a0000000)
[ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages at c17f4000, static data 35612 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 257453
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.31-21-generic root=UUID=f6d1fafc-e08e-43a9-862e-62feba350583 ro pci=routeirq
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] allocated 5191660 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:0003f5ff)
[ 0.000000] Memory: 1007600k/1038332k available (4583k kernel code, 29836k reserved, 2142k data, 544k init, 129028k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff1d000 - 0xfffff000 ( 904 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc0792000 - 0xc081a000 ( 544 kB)
[ 0.000000] .data : 0xc0579d78 - 0xc0791848 (2142 kB)
[ 0.000000] .text : 0xc0100000 - 0xc0579d78 (4583 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:472
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1993.547 MHz processor.
[ 0.001505] Console: colour VGA+ 80x25
[ 0.001508] console [tty0] enabled
[ 0.004000] hpet clockevent registered
[ 0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 3987.09 BogoMIPS (lpj=7974188)
[ 0.004000] Security Framework initialized
[ 0.004000] AppArmor: AppArmor initialized
[ 0.004000] Mount-cache hash table entries: 512
[ 0.004000] Initializing cgroup subsys ns
[ 0.004000] Initializing cgroup subsys cpuacct
[ 0.004000] Initializing cgroup subsys memory
[ 0.004000] Initializing cgroup subsys devices
[ 0.004000] Initializing cgroup subsys freezer
[ 0.004000] Initializing cgroup subsys net_cls
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] mce: CPU supports 6 MCE banks
[ 0.004000] CPU0: Thermal monitoring enabled (TM2)
[ 0.004000] using mwait in idle threads.
[ 0.004000] Performance Counters: Core2 events, Intel PMU driver.
[ 0.004000] ... version: 2
[ 0.004000] ... bit width: 40
[ 0.004000] ... generic counters: 2
[ 0.004000] ... value mask: 000000ffffffffff
[ 0.004000] ... max period: 000000007fffffff
[ 0.004000] ... fixed-purpose counters: 3
[ 0.004000] ... counter mask: 0000000700000003
[ 0.004000] Checking 'hlt' instruction... OK.
[ 0.018692] ACPI: Core revision 20090521
[ 0.222150] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.261901] CPU0: Intel(R) Core(TM)2 Duo CPU E4400 @ 2.00GHz stepping 0d
[ 0.264001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine.. 3987.09 BogoMIPS (lpj=7974180)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.004000] mce: CPU supports 6 MCE banks
[ 0.004000] CPU1: Thermal monitoring enabled (TM2)
[ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
[ 0.349488] CPU1: Intel(R) Core(TM)2 Duo CPU E4400 @ 2.00GHz stepping 0d
[ 0.350862] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.352021] Brought up 2 CPUs
[ 0.352076] Total of 2 processors activated (7974.18 BogoMIPS).
[ 0.352175] CPU0 attaching sched-domain:
[ 0.352178] domain 0: span 0-1 level MC
[ 0.352181] groups: 0 1
[ 0.352187] CPU1 attaching sched-domain:
[ 0.352189] domain 0: span 0-1 level MC
[ 0.352192] groups: 1 0
[ 0.352269] Dell OptiPlex 745 series board detected. Selecting BIOS-method for reboots.
[ 0.352269] Booting paravirtualized kernel on bare hardware
[ 0.352354] regulator: core version 0.5
[ 0.352354] Time: 10:37:37 Date: 06/01/10
[ 0.352354] NET: Registered protocol family 16
[ 0.356112] EISA bus registered
[ 0.356170] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.356253] ACPI: bus type pci registered
[ 0.356362] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.356424] PCI: MCFG area at e0000000 reserved in E820
[ 0.356480] PCI: Using MMCONFIG for extended config space
[ 0.356536] PCI: Using configuration type 1 for base access
[ 0.357668] bio: create slab <bio-0> at 0
[ 0.357668] ACPI: EC: Look up EC in DSDT
[ 0.417628] ACPI: Interpreter enabled
[ 0.417692] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.417865] ACPI: Using IOAPIC for interrupt routing
[ 0.493339] ACPI Warning: Incorrect checksum in table [TCPA] - 00, should be 89 20090521 tbutils-246
[ 0.497976] ACPI: ACPI Dock Station Driver: 1 docks/bays found
[ 0.505683] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.505849] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.505909] pci 0000:00:01.0: PME# disabled
[ 0.505989] pci 0000:00:02.0: reg 10 32bit mmio: [0xfea00000-0xfeafffff]
[ 0.505999] pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff]
[ 0.506005] pci 0000:00:02.0: reg 20 io port: [0xecb8-0xecbf]
[ 0.506044] pci 0000:00:02.1: reg 10 32bit mmio: [0xfeb00000-0xfebfffff]
[ 0.506154] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.506214] pci 0000:00:1c.0: PME# disabled
[ 0.506331] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.506391] pci 0000:00:1c.4: PME# disabled
[ 0.506572] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.506656] pci 0000:00:1f.0: quirk: region 0880-08bf claimed by ICH6 GPIO
[ 0.506718] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0c00 (mask 007f)
[ 0.506803] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 00e0 (mask 0007)
[ 0.506933] pci 0000:00:1f.2: reg 10 io port: [0xfe00-0xfe07]
[ 0.506940] pci 0000:00:1f.2: reg 14 io port: [0xfe10-0xfe13]
[ 0.506946] pci 0000:00:1f.2: reg 18 io port: [0xfe20-0xfe27]
[ 0.506952] pci 0000:00:1f.2: reg 1c io port: [0xfe30-0xfe33]
[ 0.506959] pci 0000:00:1f.2: reg 20 io port: [0xfec0-0xfecf]
[ 0.506965] pci 0000:00:1f.2: reg 24 io port: [0xecc0-0xeccf]
[ 0.506986] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.507044] pci 0000:00:1f.2: PME# disabled
[ 0.507115] pci 0000:00:1f.3: reg 10 32bit mmio: [0xfe9ffb00-0xfe9ffbff]
[ 0.507133] pci 0000:00:1f.3: reg 20 io port: [0xece0-0xecff]
[ 0.507173] pci 0000:00:1f.5: reg 10 io port: [0xfe40-0xfe47]
[ 0.507179] pci 0000:00:1f.5: reg 14 io port: [0xfe50-0xfe53]
[ 0.507186] pci 0000:00:1f.5: reg 18 io port: [0xfe60-0xfe67]
[ 0.507192] pci 0000:00:1f.5: reg 1c io port: [0xfe70-0xfe73]
[ 0.507198] pci 0000:00:1f.5: reg 20 io port: [0xfed0-0xfedf]
[ 0.507204] pci 0000:00:1f.5: reg 24 io port: [0xecd0-0xecdf]
[ 0.507225] pci 0000:00:1f.5: PME# supported from D3hot
[ 0.507283] pci 0000:00:1f.5: PME# disabled
[ 0.507381] pci 0000:00:01.0: bridge 32bit mmio: [0xfe800000-0xfe8fffff]
[ 0.507427] pci 0000:00:1c.0: bridge 32bit mmio: [0xfe700000-0xfe7fffff]
[ 0.507499] pci 0000:03:00.0: reg 10 64bit mmio: [0xfe6f0000-0xfe6fffff]
[ 0.507580] pci 0000:03:00.0: PME# supported from D3hot D3cold
[ 0.507640] pci 0000:03:00.0: PME# disabled
[ 0.507747] pci 0000:00:1c.4: bridge 32bit mmio: [0xfe600000-0xfe6fffff]
[ 0.507775] pci 0000:04:00.0: reg 10 32bit mmio: [0xfe5ff800-0xfe5ffbff]
[ 0.507832] pci 0000:04:02.0: reg 10 32bit mmio: [0xfe5ffc00-0xfe5fffff]
[ 0.507909] pci 0000:00:1e.0: transparent bridge
[ 0.507967] pci 0000:00:1e.0: bridge 32bit mmio: [0xfe500000-0xfe5fffff]
[ 0.507989] pci_bus 0000:00: on NUMA node 0
[ 0.508004] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.508521] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT]
[ 0.508953] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[ 0.509307] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.509612] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI5._PRT]
[ 1.191891] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
[ 1.192964] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
[ 1.194022] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 7 9 10 11 12 15)
[ 1.195080] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 1.196237] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 15)
[ 1.197295] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
[ 1.198415] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 15)
[ 1.199483] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 15)
[ 1.200122] SCSI subsystem initialized
[ 1.200190] libata version 3.00 loaded.
[ 1.200190] usbcore: registered new interface driver usbfs
[ 1.200190] usbcore: registered new interface driver hub
[ 1.200190] usbcore: registered new device driver usb
[ 1.200190] ACPI: WMI: Mapper loaded
[ 1.200190] PCI: Using ACPI for IRQ routing
[ 1.200190] PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
[ 1.200235] alloc irq_desc for 16 on node -1
[ 1.200237] alloc kstat_irqs on node -1
[ 1.200243] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200306] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200369] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200431] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200494] alloc irq_desc for 20 on node -1
[ 1.200496] alloc kstat_irqs on node -1
[ 1.200500] pci 0000:00:1f.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 1.200562] pci 0000:00:1f.3: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 1.200624] pci 0000:00:1f.5: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 1.200687] pci 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200749] pci 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.200810] alloc irq_desc for 18 on node -1
[ 1.200812] alloc kstat_irqs on node -1
[ 1.200816] pci 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.212013] Bluetooth: Core ver 2.15
[ 1.212090] NET: Registered protocol family 31
[ 1.212090] Bluetooth: HCI device and connection manager initialized
[ 1.212143] Bluetooth: HCI socket layer initialized
[ 1.212198] NetLabel: Initializing
[ 1.212249] NetLabel: domain hash size = 128
[ 1.212302] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.212367] NetLabel: unlabeled traffic allowed by default
[ 1.212450] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.212587] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 1.220014] Switched to high resolution mode on CPU 0
[ 1.222978] Switched to high resolution mode on CPU 1
[ 1.232025] pnp: PnP ACPI init
[ 1.232094] ACPI: bus type pnp registered
[ 1.243597] pnp 00:01: io resource (0x800-0x85f) overlaps 0000:00:1f.0 BAR 13 (0x800-0x87f), disabling
[ 1.243686] pnp 00:01: io resource (0x860-0x8ff) overlaps 0000:00:1f.0 BAR 13 (0x800-0x87f), disabling
[ 1.287255] pnp: PnP ACPI: found 10 devices
[ 1.287309] ACPI: ACPI bus type pnp unregistered
[ 1.287366] PnPBIOS: Disabled by ACPI PNP
[ 1.287426] system 00:01: ioport range 0xc00-0xc7f has been reserved
[ 1.287492] system 00:07: iomem range 0x0-0x9ffff could not be reserved
[ 1.287553] system 00:07: iomem range 0x100000-0xffffff could not be reserved
[ 1.287615] system 00:07: iomem range 0x1000000-0x3f5ffbff could not be reserved
[ 1.287698] system 00:07: iomem range 0xf0000-0xfffff could not be reserved
[ 1.287759] system 00:07: iomem range 0xc0000-0xcbfff could not be reserved
[ 1.287821] system 00:07: iomem range 0xfec00000-0xfecfffff could not be reserved
[ 1.287905] system 00:07: iomem range 0xfee00000-0xfeefffff has been reserved
[ 1.287967] system 00:07: iomem range 0xffb00000-0xffbfffff has been reserved
[ 1.288038] system 00:07: iomem range 0xffc00000-0xffffffff has been reserved
[ 1.288103] system 00:08: ioport range 0x100-0x1fe has been reserved
[ 1.288163] system 00:08: ioport range 0x200-0x277 has been reserved
[ 1.288223] system 00:08: ioport range 0x280-0x2e7 has been reserved
[ 1.288283] system 00:08: ioport range 0x2f0-0x2f7 has been reserved
[ 1.288343] system 00:08: ioport range 0x300-0x377 has been reserved
[ 1.288402] system 00:08: ioport range 0x380-0x3bb has been reserved
[ 1.288462] system 00:08: ioport range 0x3c0-0x3e7 could not be reserved
[ 1.288523] system 00:08: ioport range 0x3f6-0x3f7 has been reserved
[ 1.288583] system 00:08: ioport range 0x400-0x4cf has been reserved
[ 1.288642] system 00:08: ioport range 0x4d2-0x57f has been reserved
[ 1.288702] system 00:08: ioport range 0x580-0x677 has been reserved
[ 1.288762] system 00:08: ioport range 0x680-0x777 has been reserved
[ 1.288821] system 00:08: ioport range 0x780-0x7bb has been reserved
[ 1.288882] system 00:08: ioport range 0x7c0-0x7ff has been reserved
[ 1.288942] system 00:08: ioport range 0x8e0-0x8ff has been reserved
[ 1.289002] system 00:08: ioport range 0x900-0x9fe has been reserved
[ 1.289062] system 00:08: ioport range 0xa00-0xafe has been reserved
[ 1.289122] system 00:08: ioport range 0xb00-0xbfe has been reserved
[ 1.289182] system 00:08: ioport range 0xc80-0xcaf has been reserved
[ 1.289241] system 00:08: ioport range 0xcc0-0xcf7 has been reserved
[ 1.289301] system 00:08: ioport range 0xd00-0xdfe has been reserved
[ 1.289361] system 00:08: ioport range 0xe00-0xefe has been reserved
[ 1.289421] system 00:08: ioport range 0xf00-0xffe has been reserved
[ 1.289481] system 00:08: ioport range 0x2000-0x20fe has been reserved
[ 1.289541] system 00:08: ioport range 0x2100-0x21fe has been reserved
[ 1.289601] system 00:08: ioport range 0x2200-0x22fe has been reserved
[ 1.289662] system 00:08: ioport range 0x2300-0x23fe has been reserved
[ 1.289722] system 00:08: ioport range 0x2400-0x24fe has been reserved
[ 1.289782] system 00:08: ioport range 0x2500-0x25fe has been reserved
[ 1.289843] system 00:08: ioport range 0x2600-0x26fe has been reserved
[ 1.289903] system 00:08: ioport range 0x2700-0x27fe has been reserved
[ 1.289964] system 00:08: ioport range 0x2800-0x28fe has been reserved
[ 1.290025] system 00:08: ioport range 0x2900-0x29fe has been reserved
[ 1.290085] system 00:08: ioport range 0x2a00-0x2afe has been reserved
[ 1.290146] system 00:08: ioport range 0x2b00-0x2bfe has been reserved
[ 1.290206] system 00:08: ioport range 0x2c00-0x2cfe has been reserved
[ 1.290267] system 00:08: ioport range 0x2d00-0x2dfe has been reserved
[ 1.290327] system 00:08: ioport range 0x2e00-0x2efe has been reserved
[ 1.290387] system 00:08: ioport range 0x2f00-0x2ffe has been reserved
[ 1.290448] system 00:08: ioport range 0x5000-0x50fe has been reserved
[ 1.290508] system 00:08: ioport range 0x5100-0x51fe has been reserved
[ 1.290569] system 00:08: ioport range 0x5200-0x52fe has been reserved
[ 1.290629] system 00:08: ioport range 0x5300-0x53fe has been reserved
[ 1.290690] system 00:08: ioport range 0x5400-0x54fe has been reserved
[ 1.290750] system 00:08: ioport range 0x5500-0x55fe has been reserved
[ 1.290810] system 00:08: ioport range 0x5600-0x56fe has been reserved
[ 1.290871] system 00:08: ioport range 0x5700-0x57fe has been reserved
[ 1.290931] system 00:08: ioport range 0x5800-0x58fe has been reserved
[ 1.290992] system 00:08: ioport range 0x5900-0x59fe has been reserved
[ 1.291052] system 00:08: ioport range 0x5a00-0x5afe has been reserved
[ 1.291113] system 00:08: ioport range 0x5b00-0x5bfe has been reserved
[ 1.291173] system 00:08: ioport range 0x5c00-0x5cfe has been reserved
[ 1.291234] system 00:08: ioport range 0x5d00-0x5dfe has been reserved
[ 1.291295] system 00:08: ioport range 0x5e00-0x5efe has been reserved
[ 1.291355] system 00:08: ioport range 0x5f00-0x5ffe has been reserved
[ 1.291416] system 00:08: ioport range 0x6000-0x60fe has been reserved
[ 1.291476] system 00:08: ioport range 0x6100-0x61fe has been reserved
[ 1.291537] system 00:08: ioport range 0x6200-0x62fe has been reserved
[ 1.291597] system 00:08: ioport range 0x6300-0x63fe has been reserved
[ 1.291658] system 00:08: ioport range 0x6400-0x64fe has been reserved
[ 1.291718] system 00:08: ioport range 0x6500-0x65fe has been reserved
[ 1.291779] system 00:08: ioport range 0x6600-0x66fe has been reserved
[ 1.291839] system 00:08: ioport range 0x6700-0x67fe has been reserved
[ 1.291899] system 00:08: ioport range 0x6800-0x68fe has been reserved
[ 1.291960] system 00:08: ioport range 0x6900-0x69fe has been reserved
[ 1.292029] system 00:08: ioport range 0x6a00-0x6afe has been reserved
[ 1.292092] system 00:08: ioport range 0x6b00-0x6bfe has been reserved
[ 1.292153] system 00:08: ioport range 0x6c00-0x6cfe has been reserved
[ 1.292213] system 00:08: ioport range 0x6d00-0x6dfe has been reserved
[ 1.292274] system 00:08: ioport range 0x6e00-0x6efe has been reserved
[ 1.292334] system 00:08: ioport range 0x6f00-0x6ffe has been reserved
[ 1.292395] system 00:08: ioport range 0xa000-0xa0fe has been reserved
[ 1.292455] system 00:08: ioport range 0xa100-0xa1fe has been reserved
[ 1.292516] system 00:08: ioport range 0xa200-0xa2fe has been reserved
[ 1.293351] system 00:08: ioport range 0xa300-0xa3fe has been reserved
[ 1.293411] system 00:08: ioport range 0xa400-0xa4fe has been reserved
[ 1.293472] system 00:08: ioport range 0xa500-0xa5fe has been reserved
[ 1.293532] system 00:08: ioport range 0xa600-0xa6fe has been reserved
[ 1.293596] system 00:08: ioport range 0xa700-0xa7fe has been reserved
[ 1.293656] system 00:08: ioport range 0xa800-0xa8fe has been reserved
[ 1.293717] system 00:08: ioport range 0xa900-0xa9fe has been reserved
[ 1.293777] system 00:08: ioport range 0xaa00-0xaafe has been reserved
[ 1.293838] system 00:08: ioport range 0xab00-0xabfe has been reserved
[ 1.293899] system 00:08: ioport range 0xac00-0xacfe has been reserved
[ 1.293959] system 00:08: ioport range 0xad00-0xadfe has been reserved
[ 1.294020] system 00:08: ioport range 0xae00-0xaefe has been reserved
[ 1.294080] system 00:08: ioport range 0xaf00-0xaffe has been reserved
[ 1.294141] system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
[ 1.294203] system 00:08: iomem range 0xfeda0000-0xfedacfff has been reserved
[ 1.328913] AppArmor: AppArmor Filesystem Enabled
[ 1.329004] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 1.329063] pci 0000:00:01.0: IO window: disabled
[ 1.329121] pci 0000:00:01.0: MEM window: 0xfe800000-0xfe8fffff
[ 1.329181] pci 0000:00:01.0: PREFETCH window: disabled
[ 1.329240] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 1.329298] pci 0000:00:1c.0: IO window: disabled
[ 1.329356] pci 0000:00:1c.0: MEM window: 0xfe700000-0xfe7fffff
[ 1.329417] pci 0000:00:1c.0: PREFETCH window: disabled
[ 1.329476] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[ 1.329535] pci 0000:00:1c.4: IO window: disabled
[ 1.329594] pci 0000:00:1c.4: MEM window: 0xfe600000-0xfe6fffff
[ 1.329655] pci 0000:00:1c.4: PREFETCH window: disabled
[ 1.329714] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
[ 1.329772] pci 0000:00:1e.0: IO window: disabled
[ 1.329831] pci 0000:00:1e.0: MEM window: 0xfe500000-0xfe5fffff
[ 1.329891] pci 0000:00:1e.0: PREFETCH window: disabled
[ 1.329956] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.330018] pci 0000:00:01.0: setting latency timer to 64
[ 1.330026] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.330088] pci 0000:00:1c.0: setting latency timer to 64
[ 1.330095] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.330157] pci 0000:00:1c.4: setting latency timer to 64
[ 1.330164] pci 0000:00:1e.0: setting latency timer to 64
[ 1.330168] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 1.330170] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 1.330173] pci_bus 0000:01: resource 1 mem: [0xfe800000-0xfe8fffff]
[ 1.330176] pci_bus 0000:02: resource 1 mem: [0xfe700000-0xfe7fffff]
[ 1.330178] pci_bus 0000:03: resource 1 mem: [0xfe600000-0xfe6fffff]
[ 1.330181] pci_bus 0000:04: resource 1 mem: [0xfe500000-0xfe5fffff]
[ 1.330183] pci_bus 0000:04: resource 3 io: [0x00-0xffff]
[ 1.330186] pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffff]
[ 1.330220] NET: Registered protocol family 2
[ 1.330377] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 1.330765] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 1.331330] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 1.331616] TCP: Hash tables configured (established 131072 bind 65536)
[ 1.331676] TCP reno registered
[ 1.331817] NET: Registered protocol family 1
[ 1.331936] Trying to unpack rootfs image as initramfs...
[ 1.519836] Freeing initrd memory: 7467k freed
[ 1.524582] Simple Boot Flag at 0x7a set to 0x1
[ 1.524829] cpufreq-nforce2: No nForce2 chipset.
[ 1.524912] Scanning for low memory corruption every 60 seconds
[ 1.525075] audit: initializing netlink socket (disabled)
[ 1.525148] type=2000 audit(1275388658.524:1): initialized
[ 1.533755] highmem bounce pool size: 64 pages
[ 1.533813] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.535381] VFS: Disk quotas dquot_6.5.2
[ 1.535492] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.536114] fuse init (API version 7.12)
[ 1.536254] msgmni has been set to 1731
[ 1.536521] alg: No test for stdrng (krng)
[ 1.536586] io scheduler noop registered
[ 1.536639] io scheduler anticipatory registered
[ 1.536693] io scheduler deadline registered
[ 1.536785] io scheduler cfq registered (default)
[ 1.536851] pci 0000:00:02.0: Boot video device
[ 1.536966] alloc irq_desc for 24 on node -1
[ 1.536968] alloc kstat_irqs on node -1
[ 1.536977] pcieport-driver 0000:00:01.0: irq 24 for MSI/MSI-X
[ 1.536984] pcieport-driver 0000:00:01.0: setting latency timer to 64
[ 1.537083] alloc irq_desc for 25 on node -1
[ 1.537085] alloc kstat_irqs on node -1
[ 1.537092] pcieport-driver 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 1.537100] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.537223] alloc irq_desc for 26 on node -1
[ 1.537225] alloc kstat_irqs on node -1
[ 1.537232] pcieport-driver 0000:00:1c.4: irq 26 for MSI/MSI-X
[ 1.537240] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[ 1.537329] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.537466] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.537659] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.537743] ACPI: Power Button [PWRF]
[ 1.537845] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.537933] ACPI: Power Button [VBTN]
[ 1.538729] processor LNXCPU:00: registered as cooling_device0
[ 1.538823] processor LNXCPU:01: registered as cooling_device1
[ 1.626123] isapnp: Scanning for PnP cards...
[ 1.979273] isapnp: No Plug & Play device found
[ 1.980600] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.981009] serial 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.981073] serial 0000:04:00.0: PCI INT A disabled
[ 1.981136] serial 0000:04:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.981199] serial 0000:04:02.0: PCI INT A disabled
[ 1.982190] brd: module loaded
[ 1.982693] loop: module loaded
[ 1.982807] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.982985] ata_piix 0000:00:1f.2: version 2.13
[ 1.982997] ata_piix 0000:00:1f.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 1.983061] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.136034] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 2.136109] scsi0 : ata_piix
[ 2.136243] scsi1 : ata_piix
[ 2.142319] ata1: SATA max UDMA/133 cmd 0xfe00 ctl 0xfe10 bmdma 0xfec0 irq 20
[ 2.142384] ata2: SATA max UDMA/133 cmd 0xfe20 ctl 0xfe30 bmdma 0xfec8 irq 20
[ 2.142509] ata_piix 0000:00:1f.5: PCI INT C -> GSI 20 (level, low) -> IRQ 20
[ 2.142573] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 2.296026] ata_piix 0000:00:1f.5: setting latency timer to 64
[ 2.296079] scsi2 : ata_piix
[ 2.296202] scsi3 : ata_piix
[ 2.296293] ata3: SATA max UDMA/133 cmd 0xfe40 ctl 0xfe50 bmdma 0xfed0 irq 20
[ 2.296356] ata4: SATA max UDMA/133 cmd 0xfe60 ctl 0xfe70 bmdma 0xfed8 irq 20
[ 2.297253] Fixed MDIO Bus: probed
[ 2.297338] PPP generic driver version 2.4.2
[ 2.297471] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.297553] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.297624] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.297754] PNP: No PS/2 controller found. Probing ports directly.
[ 2.300417] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.300477] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.300586] mice: PS/2 mouse device common for all mice
[ 2.300745] rtc_cmos 00:05: RTC can wake from S4
[ 2.300829] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
[ 2.300909] rtc0: alarms up to one day, 242 bytes nvram, hpet irqs
[ 2.301060] device-mapper: uevent: version 1.0.3
[ 2.301191] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx
[ 2.301338] device-mapper: multipath: version 1.1.0 loaded
[ 2.301396] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 2.301559] EISA: Probing bus 0 at eisa.0
[ 2.301612] EISA: Cannot allocate resource for mainboard
[ 2.301673] Cannot allocate resource for EISA slot 2
[ 2.301734] Cannot allocate resource for EISA slot 5
[ 2.301789] Cannot allocate resource for EISA slot 6
[ 2.301851] EISA: Detected 0 cards.
[ 2.301973] cpuidle: using governor ladder
[ 2.302026] cpuidle: using governor menu
[ 2.302569] TCP cubic registered
[ 2.302775] NET: Registered protocol family 10
[ 2.303305] lo: Disabled Privacy Extensions
[ 2.303699] NET: Registered protocol family 17
[ 2.303769] Bluetooth: L2CAP ver 2.13
[ 2.303820] Bluetooth: L2CAP socket layer initialized
[ 2.303876] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.303930] Bluetooth: SCO socket layer initialized
[ 2.304015] Bluetooth: RFCOMM TTY layer initialized
[ 2.304079] Bluetooth: RFCOMM socket layer initialized
[ 2.304134] Bluetooth: RFCOMM ver 1.11
[ 2.304217] Using IPI No-Shortcut mode
[ 2.304327] PM: Resume from disk failed.
[ 2.304338] registered taskstats version 1
[ 2.304502] Magic number: 14:712:627
[ 2.304602] rtc_cmos 00:05: setting system clock to 2010-06-01 10:37:39 UTC (1275388659)
[ 2.304688] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.304746] EDD information not available.
[ 2.616053] ata4: SATA link down (SStatus 0 SControl 300)
[ 2.616170] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.936074] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 2.936150] ata1.01: SATA link down (SStatus 4 SControl 300)
[ 2.936388] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.936457] ata2.01: SATA link down (SStatus 4 SControl 300)
[ 2.936522] ata2.01: link offline, clearing class 3 to NONE
[ 2.944383] ata1.00: ATA-7: WDC WD800JD-75MSA3, 10.01E04, max UDMA/133
[ 2.944452] ata1.00: 156250000 sectors, multi 8: LBA48 NCQ (depth 0/32)
[ 2.952344] ata1.00: configured for UDMA/133
[ 2.952559] scsi 0:0:0:0: Direct-Access ATA WDC WD800JD-75MS 10.0 PQ: 0 ANSI: 5
[ 2.952769] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.952781] sd 0:0:0:0: [sda] 156250000 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 2.952827] sd 0:0:0:0: [sda] Write Protect is off
[ 2.952831] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.952854] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.952977] sda: sda1 sda2 <
[ 2.968228] ata2.00: ATAPI: HL-DT-ST CD-RW/DVD-ROM GCC-H10N, C103, max UDMA/100
[ 2.988405] sda5 >
[ 2.988759] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.000270] ata2.00: configured for UDMA/100
[ 3.001984] scsi 1:0:0:0: CD-ROM HL-DT-ST CDRW/DVD GCCH10N C103 PQ: 0 ANSI: 5
[ 3.003121] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 3.003190] Uniform CD-ROM driver Revision: 3.20
[ 3.003327] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 3.003366] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 3.003447] Freeing unused kernel memory: 544k freed
[ 3.003852] Write protecting the kernel text: 4584k
[ 3.003951] Write protecting the kernel read-only data: 1840k
[ 3.113410] Linux agpgart interface v0.103
[ 3.116114] agpgart-intel 0000:00:00.0: Intel 965Q Chipset
[ 3.116683] agpgart-intel 0000:00:00.0: detected 7676K stolen memory
[ 3.119793] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 3.191888] [drm] Initialized drm 1.1.0 20060810
[ 3.195512] tg3.c:v3.99 (April 20, 2009)
[ 3.195595] tg3 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.195688] tg3 0000:03:00.0: setting latency timer to 64
[ 3.204693] tg3 0000:03:00.0: PME# disabled
[ 3.206509] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 3.206576] i915 0000:00:02.0: setting latency timer to 64
[ 3.208053] mtrr: type mismatch for d0000000,10000000 old: write-back new: write-combining
[ 3.209151] Floppy drive(s): fd0 is 1.44M
[ 3.210849] [drm] MTRR allocation failed. Graphics performance may suffer.
[ 3.211457] alloc irq_desc for 27 on node -1
[ 3.211460] alloc kstat_irqs on node -1
[ 3.211470] i915 0000:00:02.0: irq 27 for MSI/MSI-X
[ 3.221037] eth0: Tigon3 [partno(BCM95754) rev b002] (PCI Express) MAC address 00:1e:4f:92:a4:5b
[ 3.221128] eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 3.221211] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 3.221270] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 3.230574] FDC 0 is a post-1991 82077
[ 3.333232] [drm] fb0: inteldrmfb frame buffer device
[ 3.333306] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 3.400630] [drm] DAC-6: set mode 1280x1024 11
[ 3.425593] Console: switching to colour frame buffer device 160x64
[ 3.807414] PM: Starting manual resume from disk
[ 3.807455] PM: Resume from partition 8:5
[ 3.807457] PM: Checking hibernation image.
[ 3.807588] PM: Resume from disk failed.
[ 3.811863] EXT4-fs (sda1): INFO: recovery required on readonly filesystem
[ 3.811922] EXT4-fs (sda1): write access will be enabled during recovery
[ 3.841903] EXT4-fs (sda1): barriers enabled
[ 3.917820] kjournald2 starting: pid 386, dev sda1:8, commit interval 5 seconds
[ 3.917887] EXT4-fs (sda1): delayed allocation enabled
[ 3.917892] EXT4-fs: file extents enabled
[ 3.923551] EXT4-fs: mballoc enabled
[ 3.923594] EXT4-fs (sda1): recovery complete
[ 3.923959] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 4.583450] type=1505 audit(1275388661.778:2): operation="profile_load" pid=414 name=/usr/share/gdm/guest-session/Xsession
[ 4.586028] type=1505 audit(1275388661.779:3): operation="profile_load" pid=415 name=/sbin/dhclient3
[ 4.586880] type=1505 audit(1275388661.779:4): operation="profile_load" pid=415 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 4.587355] type=1505 audit(1275388661.779:5): operation="profile_load" pid=415 name=/usr/lib/connman/scripts/dhclient-script
[ 4.664691] type=1505 audit(1275388661.859:6): operation="profile_load" pid=416 name=/usr/bin/evince
[ 4.676624] type=1505 audit(1275388661.871:7): operation="profile_load" pid=416 name=/usr/bin/evince-previewer
[ 4.683624] type=1505 audit(1275388661.875:8): operation="profile_load" pid=416 name=/usr/bin/evince-thumbnailer
[ 4.699734] type=1505 audit(1275388661.891:9): operation="profile_load" pid=418 name=/usr/lib/cups/backend/cups-pdf
[ 4.700667] type=1505 audit(1275388661.895:10): operation="profile_load" pid=418 name=/usr/sbin/cupsd
[ 10.679389] udev: starting version 147
[ 10.717323] Adding 2980016k swap on /dev/sda5. Priority:-1 extents:1 across:2980016k
[ 10.774550] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 10.775158] dell-wmi: No known WMI GUID found
[ 10.806336] lp: driver loaded but no devices found
[ 10.847838] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.983877] EXT4-fs (sda1): internal journal on sda1:8
[ 11.244827] tg3 0000:03:00.0: PME# disabled
[ 11.244910] alloc irq_desc for 28 on node -1
[ 11.244913] alloc kstat_irqs on node -1
[ 11.244927] tg3 0000:03:00.0: irq 28 for MSI/MSI-X
[ 11.320592] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.512993] __ratelimit: 3 callbacks suppressed
[ 11.512997] type=1505 audit(1275388668.707:12): operation="profile_replace" pid=916 name=/usr/share/gdm/guest-session/Xsession
[ 11.514892] type=1505 audit(1275388668.707:13): operation="profile_replace" pid=918 name=/sbin/dhclient3
[ 11.515629] type=1505 audit(1275388668.707:14): operation="profile_replace" pid=918 name=/usr/lib/NetworkManager/nm-dhcp-client.action
[ 11.516028] type=1505 audit(1275388668.711:15): operation="profile_replace" pid=918 name=/usr/lib/connman/scripts/dhclient-script
[ 11.521128] type=1505 audit(1275388668.715:16): operation="profile_replace" pid=920 name=/usr/bin/evince
[ 11.533293] type=1505 audit(1275388668.727:17): operation="profile_replace" pid=920 name=/usr/bin/evince-previewer
[ 11.540436] type=1505 audit(1275388668.735:18): operation="profile_replace" pid=920 name=/usr/bin/evince-thumbnailer
[ 11.550552] type=1505 audit(1275388668.743:19): operation="profile_replace" pid=924 name=/usr/lib/cups/backend/cups-pdf
[ 11.551405] type=1505 audit(1275388668.743:20): operation="profile_replace" pid=924 name=/usr/sbin/cupsd
[ 11.554361] type=1505 audit(1275388668.747:21): operation="profile_replace" pid=925 name=/usr/sbin/tcpdump
[ 11.567486] ttyS0: LSR safety check engaged!
[ 11.568061] ttyS0: LSR safety check engaged!
[ 12.707234] CPU0 attaching NULL sched-domain.
[ 12.707239] CPU1 attaching NULL sched-domain.
[ 12.720359] CPU0 attaching sched-domain:
[ 12.720365] domain 0: span 0-1 level MC
[ 12.720369] groups: 0 1
[ 12.720377] domain 1: span 0-1 level CPU
[ 12.720382] groups: 0-1 (__cpu_power = 2048)
[ 12.720390] CPU1 attaching sched-domain:
[ 12.720394] domain 0: span 0-1 level MC
[ 12.720398] groups: 1 0
[ 12.720405] domain 1: span 0-1 level CPU
[ 12.720409] groups: 0-1 (__cpu_power = 2048)
[ 12.862372] tg3: eth0: Link is up at 100 Mbps, full duplex.
[ 12.862376] tg3: eth0: Flow control is on for TX and on for RX.
[ 12.862730] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 18.189098] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.189106] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.189114] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 18.189123] end_request: I/O error, dev sr0, sector 1413064
[ 18.190745] Buffer I/O error on device sr0, logical block 176633
[ 22.810071] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 22.810078] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 22.810085] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 22.810095] end_request: I/O error, dev sr0, sector 1413064
[ 22.811794] Buffer I/O error on device sr0, logical block 176633
[ 23.812012] eth0: no IPv6 routers present
[ 27.504906] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 27.504913] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 27.504920] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 27.504929] end_request: I/O error, dev sr0, sector 1413064
[ 27.506686] Buffer I/O error on device sr0, logical block 176633
[ 32.172102] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 32.172109] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 32.172116] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 32.172125] end_request: I/O error, dev sr0, sector 1413064
[ 32.173946] Buffer I/O error on device sr0, logical block 176633
[ 37.762946] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 37.762954] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 37.762962] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 37.762972] end_request: I/O error, dev sr0, sector 1413064
[ 37.764840] Buffer I/O error on device sr0, logical block 176633
[ 43.329441] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 43.329448] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 43.329455] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 43.329464] end_request: I/O error, dev sr0, sector 1413064
[ 43.331316] Buffer I/O error on device sr0, logical block 176633
[ 49.335683] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 49.335690] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 49.335697] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 49.335706] end_request: I/O error, dev sr0, sector 1413064
[ 49.337589] Buffer I/O error on device sr0, logical block 176633
[ 55.366012] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 55.366018] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 55.366025] sr 1:0:0:0: [sr0] Add. Sense: Illegal mode for this track
[ 55.366034] end_request: I/O error, dev sr0, sector 1413064
[ 55.367924] Buffer I/O error on device sr0, logical block 176633
Module Size Used by
binfmt_misc 8356 1
iptable_filter 3100 0
ip_tables 11692 1 iptable_filter
x_tables 16544 1 ip_tables
dell_wmi 2564 0
dcdbas 7292 0
lp 8964 0
parport 35340 1 lp
psmouse 57332 0
serio_raw 5280 0
fbcon 36640 70
tileblit 2460 1 fbcon
font 8124 1 fbcon
bitblit 5372 1 fbcon
softcursor 1756 1 bitblit
floppy 54916 0
i915 226120 1
tg3 109632 0
drm 160032 1 i915
i2c_algo_bit 5760 1 i915
video 19380 1 i915
output 2780 1 video
intel_agp 27676 2 i915
agpgart 34988 2 drm,intel_agp
