Yesterday I informed our LSI (inheritor of the former AgereSystems code) of the desirability of updated the Linux agrsm code, to include support for the host 8086:3b56 Audio device: Intel Corp 5 Series/3400 Series Chipset High Definition Audio of their 11c11040 chip. One shouldn't assume that a fix will soon be provided. While LSI staff are typically sympathetic, until some major buyer of their chips will sponsor the coding, management will not make the investment in Linux coding. But to their credit, they recently provided an update providing support for the new PCI card 11c1:0630 modem chip, together with an update of the older code for the 11c1:0620 chip. MarvS On Wed, Mar 10, 2010 at 3:17 AM, Benjamin Colling <bbj17@xxxxxx> wrote: > Hi Bjorn, > > linux:~ # cat /proc/asound/card0/codec#1 > Codec: LSI ID 1040 > Address: 1 > Function Id: 0x2 > Vendor Id: 0x11c11040 > Subsystem Id: 0x11c10001 > Revision Id: 0x100200 > Modem Function Group: 0x1 > > I think the new Intel Chipset is the problem. > > Lspci: > 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) > Subsystem: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio > Flags: bus master, fast devsel, latency 0, IRQ 22 > Memory at 9c820000 (64-bit, non-prefetchable) [size=16K] > Capabilities: [50] Power Management version 2 > Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ > Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 > Capabilities: [100] Virtual Channel <?> > Capabilities: [130] Root Complex Link <?> > Kernel driver in use: HDA Intel > > lspci -n: > 00:1b.0 0403: 8086:3b56 (rev 06) > > Ben > > > -----Ursprüngliche Nachricht----- > Von: Bjorn Wielens [mailto:Uniacke1@xxxxxxxx] > Gesendet: Dienstag, 9. März 2010 21:01 > An: Benjamin Colling > Cc: 'Marvin Stodolsky'; discuss@xxxxxxxxxxxxx > Betreff: Re: AW: agere softmodem HDA + Intel Ibex Peak High Definition Audio > > Just an FYI, I can confirm that my 11c11040 does work on this system/kernel. > > Can you post the results of 'cat /proc/asound/card0/codec#1'? > > This will confirm modem type. > > Bjorn. > > > > On 03/09/2010 10:26 AM, Benjamin Colling wrote: >> Hi Marvin, >> >> my last test was actually with an openSUSE 11.2 System with Kernel 2.6.31.5. >> The output of scanModem was based on Live-CD (Knoppix 6.2.1) with >> Kernel 2.6.32.6 >> >> >> Here is the scanmodem output (openSUSE) with disabled snd-hda-intel power-feature: >> >> -------------------------- System information >> ---------------------------- CPU=i686, Welcome , ALSA_version=1.0.20 >> Linux version 2.6.31.8-0.1-default (geeko@buildhost) (gcc version >> 4.4.1 [gcc-4_4-branch revision 150839] (SUSE Linux) ) #1 SMP >> 2009-12-15 23:55:40 +0100 scanModem update of: 2010_02_25 >> >> /etc/lsb-release not found >> >> >> Presently install your Linux Distributions dkms package. It provides >> for automated driver updates, following upgrade of your kernel. For >> details see http://linux.dell.com/projects.shtml#dkms >> >> There are no blacklisted modem drivers in /etc/modprobe* files >> >> Potentially useful modem drivers now loaded are: >> snd_hda_intel >> >> Attached USB devices are: >> ID 8087:0020 >> ID 3538:0054 Power Quotient International Co., Ltd Flash Drive (2GB) >> ID 8087:0020 If a cellphone is not detected, see >> http://ubuntuforums.org/archive/index.php/t-878554.html >> A sample report is: >> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html >> >> If a USB modem or cellphone is attached and was not detected, please >> provide available information in your request to discuss@xxxxxxxxxxxxx >> >> Candidate PCI devices with modem chips are: >> 00:16.0 Communication controller: Intel Corporation 5 Series/3400 >> Series Chipset HECI Controller (rev 06) >> 00:16.3 Serial controller: Intel Corporation 5 Series/3400 Series >> Chipset KT Controller (rev 06) 00:1b.0 Audio device: Intel Corporation >> 5 Series/3400 Series Chipset High Definition Audio (rev 06) High Definition Audio cards can host modem chips. >> >> For candidate card in slot 00:16.0, firmware information and bootup diagnostics are: >> PCI slot PCI ID SubsystemID Name >> ---------- --------- --------- -------------- >> 00:16.0 8086:3b64 8086:3b64 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller >> >> Modem interrupt assignment and sharing: >> 25: 0 0 0 0 HPET_MSI-edge hpet3 >> --- Bootup diagnostics for card in PCI slot 00:16.0 ---- >> [ 2.662162] pci 0000:00:16.0: reg 10 64bit mmio: [0x9c827900-0x9c82790f] >> [ 2.662215] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold >> [ 2.662219] pci 0000:00:16.0: PME# disabled >> >> The PCI slot 00:16.0 of the modem card may be disabled early in a >> bootup process, but then enabled later. If modem drivers load but >> the modem is not responsive, read DOCs/Bootup.txt about possible fixes. >> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx if >> help is needed. >> >> >> For candidate card in slot 00:16.3, firmware information and bootup diagnostics are: >> PCI slot PCI ID SubsystemID Name >> ---------- --------- --------- -------------- >> 00:16.3 8086:3b67 8086:3b67 Serial controller: Intel Corporation 5 Series/3400 Series Chipset KT Controller >> >> Modem interrupt assignment and sharing: >> 17: 0 1 1 1 IO-APIC-fasteoi yenta >> --- Bootup diagnostics for card in PCI slot 00:16.3 ---- >> [ 2.662356] pci 0000:00:16.3: reg 10 io port: [0x6080-0x6087] >> [ 2.662362] pci 0000:00:16.3: reg 14 32bit mmio: [0x9c826000-0x9c826fff] >> [ 3.143929] serial 0000:00:16.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 >> [ 3.143995] 0000:00:16.3: ttyS4 at I/O 0x6080 (irq = 17) is a 16550A >> >> For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are: >> PCI slot PCI ID SubsystemID Name >> ---------- --------- --------- -------------- >> 00:1b.0 8086:3b56 8086:3b56 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio >> >> Modem interrupt assignment and sharing: >> 22: 933 932 901 912 IO-APIC-fasteoi ehci_hcd:usb1, HDA Intel >> --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- >> [ 2.662628] pci 0000:00:1b.0: reg 10 64bit mmio: [0x9c820000-0x9c823fff] >> [ 2.662664] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold >> [ 2.662667] pci 0000:00:1b.0: PME# disabled >> [ 11.862240] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 >> [ 11.862275] HDA Intel 0000:00:1b.0: setting latency timer to 64 >> [ 12.000169] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6 >> [ 12.011602] input: HDA Intel Mic at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 >> [ 12.011740] input: HDA Intel Speaker at Int N/A Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 >> [ 12.011840] input: HDA Intel HP Out at Ext Left Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 >> [ 170.111634] HDA Intel 0000:00:1b.0: PCI INT A disabled [ >> 704.714667] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) >> -> IRQ 22 [ 704.714699] HDA Intel 0000:00:1b.0: setting latency timer >> to 64 [ 704.831187] input: HDA Digital PCBeep as >> /devices/pci0000:00/0000:00:1b.0/input/input10 >> [ 704.844109] input: HDA Intel Mic at Ext Left Jack as >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 >> [ 704.844203] input: HDA Intel Speaker at Int N/A Jack as >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 >> [ 704.844275] input: HDA Intel HP Out at Ext Left Jack as >> /devices/pci0000:00/0000:00:1b.0/sound/card0/input13 >> >> The PCI slot 00:1b.0 of the modem card may be disabled early in a >> bootup process, but then enabled later. If modem drivers load but >> the modem is not responsive, read DOCs/Bootup.txt about possible fixes. >> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx if >> help is needed. >> >> >> === Finished firmware and bootup diagnostics, next deducing cogent >> software. === Completed candidate modem analyses. >> >> The base of the UDEV device file system is: /dev/.udev >> >> Versions adequately match for the compiler installed: 4.4.1 >> and the compiler used in kernel assembly: 4.4 >> >> linux-headers-2.6.31.8-0.1-default resources needed for compiling are not manifestly ready! >> The patch utility is needed for compiling ALSA drivers, and possibly others. >> >> If compiling is necessary packages must be installed, providing: >> kernel-source-2.6.31.8-0.1-default >> >> >> If a driver compilation fails, with message including some lack of >> some FileName.h (stdio.h for example), then Some additional >> kernel-header files need installation to /usr/include. The minimal >> additional packages are libc6-dev and any of its dependents, under >> Ubuntu linux-libc-dev >> >> If an alternate ethernet connection is available, $ apt-get update $ >> apt-get -s install linux-kernel-devel will install needed packages. >> For Debian/Ubuntu related distributions, run the following command to display the needed package list: >> >> Otherwise packages have to be found through http://packages.ubuntu.com >> Once downloaded and transferred into a Linux partition, they can be >> installed alltogether with: >> $ sudo dpkg -i *.deb >> >> >> Checking pppd properties: >> -rwxr-xr-x 1 root dialout 330764 Oct 19 17:45 /usr/sbin/pppd >> >> In case of an "error 17" "serial loopback" problem, see: >> >> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html >> >> To enable dialout without Root permission do: >> $ su - root (not for Ubuntu) >> chmod a+x /usr/sbin/pppd >> or under Ubuntu related Linuxes >> chmod a+x /usr/sbin/pppd >> >> Checking settings of: /etc/ppp/options >> noipdefault >> noauth >> crtscts >> lock >> modem >> asyncmap 0 >> nodetach >> lcp-echo-interval 30 >> lcp-echo-failure 4 >> lcp-max-configure 60 >> lcp-restart 2 >> idle 600 >> noipx >> file /etc/ppp/filters >> >> In case of a message like: >> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied >> see >> http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html >> >> For guidance on FAX usage, get from >> http://linmodems.technion.ac.il/packages/ get faxing.tar.gz It has samples for a modem using port /dev/ttySL0, which must be changed to match your modem's port. >> >> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 >> eth1 Which can interfere with Browser naviagation. >> >> Don't worry about the following, it is for experts should trouble shooting be necessary. >> ========================================================== >> >> Checking for modem support lines: >> -------------------------------------- >> /device/modem symbolic link: >> slmodemd created symbolic link /dev/ttySL0: >> Within /etc/udev/ files: >> /etc/udev/rules.d/51-hso-udev.rules:SUBSYSTEM=="tty", SUBSYSTEMS=="usb", ATTR{hsotype}=="Modem", SYMLINK+="wmodem0" >> /etc/udev/rules.d/51-hso-udev.rules:SUBSYSTEM=="tty", SYSFS{hsotype}=="Modem", SYMLINK+="wmodem0" >> /etc/udev/rules.d/77-network.rules:SUBSYSTEM=="net", ENV{INTERFACE}=="lo*|dummy*|vif*.*|br*|bond*|vlan*|gre*|sit*|tap*|tun*|ipip*|ip6tnl*|ipsec*|ppp*|ippp*|isdn*|modem*|dsl*|plip*|irda*", GOTO="skip_ifup" >> Within /etc/modprobe.conf files: >> /etc/modprobe.d/00-system.conf:# Linux ACP modem (Mwave) >> Within any ancient /etc/devfs files: >> >> Within ancient kernel 2.4.n /etc/module.conf files: >> >> --------- end modem support lines -------- >> >> >> >> Ben >> >> >> >> -----Ursprüngliche Nachricht----- >> Von: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] >> Gesendet: Dienstag, 9. März 2010 14:44 >> An: Benjamin Colling >> Cc: discuss@xxxxxxxxxxxxx >> Betreff: Re: agere softmodem HDA + Intel Ibex Peak High Definition >> Audio >> >> Ben, >> >> The last kernel for which others are having success with the 11c11040 >> modem chip on HDA cards is 2.6.31, rather than the 2.6.32 you are now >> using. Would you please install an earlier kernel and check again for >> modem detection. >> >> MarvS >> >> On Tue, Mar 9, 2010 at 6:26 AM, Benjamin Colling <bbj17@xxxxxx> wrote: >>> Hi Marv, >>> >>> based on agrsm-11c11040-2.1.80~20091225 >>> >>> I loaded the module (after rmmod snd*): >>> >>> modprobe snd-hda-intel power_save=0 power_save_controller=N >>> >>> here is dmesg output: >>> >>> [ 4850.630868] HDA Intel 0000:00:1b.0: PCI INT A disabled [ >>> 4951.043238] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) >>> -> IRQ 22 [ 4951.043291] HDA Intel 0000:00:1b.0: setting latency >>> timer to 64 [ 4951.174798] ALSA /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pci/hda/hda_codec.c:3881: autoconfig: line_outs=1 (0xd/0x0/0x0/0x0/0x0) >>> [ 4951.174807] ALSA /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pci/hda/hda_codec.c:3885: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) >>> [ 4951.174815] ALSA /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pci/hda/hda_codec.c:3889: hp_outs=1 (0xb/0x0/0x0/0x0/0x0) >>> [ 4951.174822] ALSA /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pci/hda/hda_codec.c:3890: mono: mono_out=0x0 >>> [ 4951.174828] ALSA /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pci/hda/hda_codec.c:3901: inputs: mic=0xa, fmic=0x0, line=0x0, fline=0x0, cd=0x0, aux=0x0 >>> [ 4951.175130] ALSA >>> /usr/src/packages/BUILD/kernel-default-2.6.31.5/linux-2.6.31/sound/pc >>> i/hda/patch_sigmatel.c:2969: stac92xx: dac_nids=1 >>> (0x13/0x0/0x0/0x0/0x0) [ 4951.175491] input: HDA Digital PCBeep as >>> /devices/pci0000:00/0000:00:1b.0/input/input9 >>> [ 4951.219719] input: HDA Intel Mic at Ext Left Jack as >>> /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 >>> [ 4951.219814] input: HDA Intel Speaker at Int N/A Jack as >>> /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 >>> [ 4951.219886] input: HDA Intel HP Out at Ext Left Jack as >>> /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 >>> [ 5119.756528] * Hello Agere Driver ** [ 5119.756610] usbcore: >>> registered new interface driver agr12dec2006 [ 5121.281565] Loading >>> module Agere Modem Controller driver version 2.1.80 (2007-10-01) [ >>> 5125.431340] serial8250_register_ports: BaseAddress 0x0400 Irq 3 [ >>> 5125.431354] ttyAGS3 at I/O 0x400 (irq = 3) is a AgereModem [ >>> 5125.431439] agrserial - ret_val 0, call: lt_modem_ops.init_modem [ >>> 5125.431449] Loading module Agere Modem Interface driver version >>> 2.1.80.0 (2007-10-01) >>> >>> Created the link: ln -s /dev/ttySAGR /dev/ttyAGS3 >>> >>> Executed wvdialconf: >>> >>> Editing `/etc/wvdial.conf'. >>> >>> Scanning your serial ports for a modem. >>> >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> Modem Port Scan<*1>: S1 S2 S3 >>> ttyS4<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttyS4<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>> ttyS4<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> Modem Port Scan<*1>: S5 S6 S7 >>> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>> ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 >>> baud >>> ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>> >>> >>> dmesg-output (original numSupportedDevice): >>> >>> [ 5235.659191] ==> codecType = 0x31 >>> [ 5235.659200] ERR: Control Interface failed >>> >>> >>> dmesg-output (numSupportedDevice { 0x8086, 0x3b56, 0x0000, 0x0000 },) >>> [ 5438.363024] ==> codecType = 0xffffff58 >>> >>> Ben >>> >>> >>> >>> -----Ursprüngliche Nachricht----- >>> Von: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] >>> Gesendet: Montag, 8. März 2010 20:45 >>> An: Benjamin Colling >>> Cc: discuss@xxxxxxxxxxxxx >>> Betreff: Re: agere softmodem HDA + Intel Ibex Peak High Definition >>> Audio >>> >>> Ben, >>> >>> VEN_11C1&DEV_1040 is equivalent under Linux do the 11c11040 chip >>> which is hosted on the Subsystem of you HDAudio card. >>> >>> Nikolay has shown that the following change is necessary under >>> 2.6.31+ kernels Do $ sudo gedit /etc/modprobe.d/alsa-base.conf Near >>> the end of the file there is a line: >>> options snd-hda-intel power_save=10 power_save_controller=N >>> model=mbp3 Change the power_save=10, to 0, per line below: >>> options snd-hda-intel power_save=0 power_save_controller=N model=mbp3 >>> >>> Then reboot, and retest the modem with: >>> # wvdialconf >>> Of course first make sure the drivers are loaded & remember to set a >>> symbolic link. >>> # ln -s /dev/ttySAGR /dev/ttyAGS3 >>> >>> MarvS >>> scanModem manitainer >>> >>> >>> On Mon, Mar 8, 2010 at 12:32 PM, Benjamin Colling <bbj17@xxxxxx> wrote: >>>> Hi, >>>> >>>> It is a laptop. >>>> In Windows 7 the modem is shown as: "Agere Systems HDA Modem" >>>> >>>> Windows Modem-HardwareIDs >>>> HDAUDIO\FUNC_02&VEN_11C1&DEV_1040&SUBSYS_11C10001&REV_1002 >>>> HDAUDIO\FUNC_02&VEN_11C1&DEV_1040&SUBSYS_11C10001 >>>> >>>> Driver Details: >>>> C:\Windows\system32\Drivers\AGRSM.sys >>>> LSI Corp >>>> 2.2.89.2 >>>> >>>> Modem-Test: >>>> >>>> ATQ0V1E0 - OK >>>> AT+GMM - H.324 video-ready rev. 1.0 >>>> AT+FCLASS=? - 0,1,8 >>>> AT#CLS=? - BEFEHL WIRD NICHT UNTERSTÜTZT >>>> AT+GCI? - +GCI:04 >>>> AT+GCI=? - >>>> +GCI:(00,01,02,04,06,07,09,0A,0B,0C,0D,0E,0F,10,11,12,14,15,16,19,1A >>>> +,1B,1D,1 >>>> E,1F,20,21,22,23,24,25,26,27,29,2B,2D,2E,2F,30,31,32,33,35,36,37,38, >>>> 3C,3D,40 >>>> ,41,43,44,45,46,47,48,49,4B,4C,4D,4E,4F,50,51,52,53,54,57,58,59,5A,5 >>>> B,5E,5F, >>>> 61,62,63,64,66,68,69,6A,6B,6C,6D,6F,70,72,73,74,77,78,7A,7B,7C,7D,7E >>>> ,7F,80,8 >>>> 1,82,83,84,85,86,87,88,89,8A,8B,8C,8D,8E,8F,90,93,96,97,98,99,9B,9C, >>>> 9F,A0,A1 >>>> ,A3,A4,A5,A6,A7,A8,A9,AA,AC,AD,AE,B2,B3,B4,B5,B6,B7,B8,BB,BC,BF,C1,C >>>> 2,C4) >>>> ATI1 - OK >>>> ATI2 - OK >>>> ATI3 - LSI Softmodem Version 2.2.89.2 >>>> ATI4 - Built on 11/10/2008 09:51:51 >>>> ATI5 - 2.2.89.2, HDA MB, HDA, A35 S-Rev:2 L-Rev:3, 06 >>>> ATI6 - OK >>>> ATI7 - HDA MB >>>> >>>> >>>> Benjamin >>>> >>>> >>>> -----Ursprüngliche Nachricht----- >>>> Von: Jacques Goldberg [mailto:Jacques.Goldberg@xxxxxxx] >>>> Gesendet: Montag, 8. März 2010 18:00 >>>> An: Benjamin Colling >>>> Cc: discuss@xxxxxxxxxxxxx >>>> Betreff: Re: agere softmodem HDA + Intel Ibex Peak High Definition >>>> Audio >>>> >>>> Benjamin, >>>> >>>> >>>> In your scanModem output there is no sign of presence of any Agere >>>> modem hardware (which would couple to the agrsm driver). >>>> >>>> The driver is a program, not hardware. You can always send soem data >>>> to any program: perhaps the driver tries to do soemthing, but >>>> whatever it will do will be sent into vacuum, The presence of the >>>> agrsm can only cause trouble when trying to use the right driver. >>>> >>>> >>>> The Intel HECI controller can in no way drive a modem. HECI has >>>> nothing to do with that. >>>> >>>> >>>> Thus scanModem has not found anything resembling a modem in your computer. >>>> >>>> >>>> "Hopefully" (poor you) you may have Windows running on the same machine. >>>> >>>> In the folder where scanModem created its output (the file >>>> ModemData.txt), there is information of using Windows in identifying >>>> some of the modem information, often enough to know how to proceed >>>> under Linux. >>>> >>>> Please try that approach. >>>> >>>> It would help us a lot to know if your computer is a laptop or a >>>> desktop. If destop, open the box and follow back the cable >>>> connected to the modem jack until you land on a card or on a chip, >>>> and copy for us anything readable on the card or chip. >>>> >>>> >>>> Jacques >>>> >>>> >>>> Benjamin Colling wrote: >>>> >>>>> Hi, >>>>> >>>>> agrsm-11c11040 packages was not recommended by scanModem utility. >>>>> But I >>>> did >>>>> not find any other software. >>>>> >>>>> >>>>>>> What does the following reports? >>>>>>> >>>>>>>>> sudo wvdialconf /etc/wvdial.conf >>>>>>>>> >>>>> >>>>> Wvdial (original numSupportedDevice) >>>>> --> WvDial: Internet dialer version 1.60 Initializing modem. >>>>> --> Sending: ATZ >>>>> --> Sending: ATQ0 >>>>> --> Re-Sending: ATZ >>>>> --> Modem not responding. >>>>> >>>>> Kernel-Msg: >>>>> [ 1757.377343] ==> codecType = 0x31 [ 1757.377349] ERR: Control >>>>> Interface failed >>>>> >>>>> >>>>> >>>>>>> I run 'nm agrmodemlib.o_shipped | grep numSupportedDevice' >>>>>>> and it tells me the binary blob is using the variable in some way. >>>>>>> Maybe something inside that blob maxed out when you added the line? >>>>>>> What if instead of adding the line you replace some existing line >>>>>>> with your line? >>>>>>> >>>>> >>>>> I changed an existing line but get this output, when accessing the >>>>> device with wvdial: >>>>> >>>>> [ 1949.953524] * Hello Agere Driver ** [ 1949.953585] usbcore: >>>>> registered new interface driver agr12dec2006 [ 1951.198280] Loading >>>>> module Agere Modem Controller driver version 2.1.80 >>>>> (2007-10-01) >>>>> [ 1960.368259] serial8250_register_ports: BaseAddress 0x0400 Irq 3 >>>>> [ 1960.368267] ttyAGS3 at I/O 0x400 (irq = 3) is a AgereModem [ >>>>> 1960.368685] agrserial - ret_val 0, call: lt_modem_ops.init_modem [ >>>>> 1960.368690] Loading module Agere Modem Interface driver version >>>> 2.1.80.0 >>>>> (2007-10-01) >>>>> [ 1975.377046] ==> codecType = 0x6c466174 >>>>> >>>>> >>>>> >>>>> >>>>> Here is the output of scanModem: >>>>> >>>>> -------------------------- System information >>>> ---------------------------- >>>>> CPU=i686, debian , ALSA_version=1.0.21 Linux version 2.6.32.6 >>>>> (root@Knoppix) (gcc version 4.4.3 20100108 >>>>> (prerelease) (Debian 4.4.2-9) ) #8 SMP PREEMPT Thu Jan 28 10:51:16 >>>>> CET >>>> 2010 >>>>> scanModem update of: 2010_02_25 >>>>> The modem symbolic link is /dev/modem -> /dev/ttyAGS3 >>>>> /etc/lsb-release not found >>>>> >>>>> >>>>> Presently install your Linux Distributions dkms package. It >>>>> provides for automated driver updates, following upgrade of your >>>>> kernel. For details see http://linux.dell.com/projects.shtml#dkms >>>>> >>>>> There are no blacklisted modem drivers in /etc/modprobe* files >>>>> >>>>> Potentially useful modem drivers now loaded are: >>>>> snd_hda_intel agrmodem agrserial >>>>> >>>>> Attached USB devices are: >>>>> ID 3538:0054 Power Quotient International Co., Ltd Flash Drive >>>>> (2GB) ID 8087:0020 Intel Corp. Integrated Rate Matching Hub ID >>>>> 8087:0020 Intel Corp. Integrated Rate Matching Hub If a cellphone >>>>> is not detected, see >>>>> http://ubuntuforums.org/archive/index.php/t-878554.html >>>>> A sample report is: >>>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.htm >>>>> l >>>>> >>>>> If a USB modem or cellphone is attached and was not detected, >>>>> please provide available information in your request to >>>>> discuss@xxxxxxxxxxxxx >>>>> >>>>> Candidate PCI devices with modem chips are: >>>>> 00:16.0 Communication controller: Intel Corporation 5 Series/3400 >>>>> Series Chipset HECI Controller (rev 06) >>>>> 00:16.3 Serial controller: Intel Corporation 5 Series/3400 Series >>>>> Chipset >>>> KT >>>>> Controller (rev 06) >>>>> 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series >>>>> Chipset High Definition Audio (rev 06) High Definition Audio cards >>>>> can host modem chips. >>>>> >>>>> For candidate card in slot 00:16.0, firmware information and bootup >>>>> diagnostics are: >>>>> PCI slot PCI ID SubsystemID Name >>>>> ---------- --------- --------- -------------- >>>>> 00:16.0 8086:3b64 8086:3b64 Communication controller: >>>>> Intel Corporation 5 Series/3400 Series Chipset HECI Controller >>>>> >>>>> Modem interrupt assignment and sharing: >>>>> 25: 0 0 0 0 HPET_MSI-edge hpet3 >>>>> --- Bootup diagnostics for card in PCI slot 00:16.0 ---- >>>>> >>>>> For candidate card in slot 00:16.3, firmware information and bootup >>>>> diagnostics are: >>>>> PCI slot PCI ID SubsystemID Name >>>>> ---------- --------- --------- -------------- >>>>> 00:16.3 8086:3b67 8086:3b67 Serial controller: Intel >>>>> Corporation 5 Series/3400 Series Chipset KT Controller >>>>> >>>>> Modem interrupt assignment and sharing: >>>>> 17: 14 17 11 10 IO-APIC-fasteoi yenta >>>>> --- Bootup diagnostics for card in PCI slot 00:16.3 ---- >>>>> [ 15.421013] serial 0000:00:16.3: PCI INT B -> GSI 17 (level, low) -> >>>> IRQ >>>>> 17 >>>>> [ 15.421260] 0000:00:16.3: ttyS1 at I/O 0x6080 (irq = 17) is a 16550A >>>>> >>>>> For candidate card in slot 00:1b.0, firmware information and bootup >>>>> diagnostics are: >>>>> PCI slot PCI ID SubsystemID Name >>>>> ---------- --------- --------- -------------- >>>>> 00:1b.0 8086:3b56 8086:3b56 Audio device: Intel >>>>> Corporation 5 Series/3400 Series Chipset High Definition Audio >>>>> >>>>> Modem interrupt assignment and sharing: >>>>> 22: 1003 995 1012 1007 IO-APIC-fasteoi >>>>> ehci_hcd:usb1, HDA Intel >>>>> --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- >>>>> [ 15.098895] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> >>>>> IRQ 22 >>>>> [ 15.098931] HDA Intel 0000:00:1b.0: setting latency timer to 64 >>>>> >>>>> === Finished firmware and bootup diagnostics, next deducing cogent >>>> software. >>>>> === >>>>> Completed candidate modem analyses. >>>>> >>>>> The base of the UDEV device file system is: /dev/.udev >>>>> >>>>> Versions adequately match for the compiler installed: 4.4.3 >>>>> and the compiler used in kernel assembly: 4.4.3 >>>>> >>>>> >>>>> >>>>> Minimal compiling resources appear complete: >>>>> make utility - /usr/bin/make >>>>> Compiler version 4.4 >>>>> linuc_headers base folder /lib/modules/2.6.32.6/build >>>>> >>>>> However some compilations and executable functions may need >>>>> additional files, in the FileNames.h (so called kernel "h"eaders) >>>>> collection installed in /usr/include/ . >>>>> For martian_modem, additional required packages are needed. The >>>>> also required headers of package libc6 are commonly installed by default. >>>>> Compiling hsfmodem drivers does require linux-libc-dev and >>>>> libc6-dev packages, for kernels 2.6.24 and later versions. >>>>> In not included on your install CD, search for them at >>>>> http://packages.ubuntu.com or comparable Repository for other >>>>> Linux distros. >>>>> When compiling ALSA drivers, the utility "patch" will also be needed. >>>>> >>>>> >>>>> Compressed files at: /usr/src/linux-source-2.6.32.6.tar.bz2 >>>>> >>>>> For Debian and some related distributions, a package >>>>> kernel-kbuild-2.6-32 may be needed to support driver compiling. >>>>> >>>>> >>>>> If a driver compilation fails, with message including some lack of >>>>> some FileName.h (stdio.h for example), then Some additional >>>>> kernel-header files need installation to /usr/include. The minimal >>>>> additional packages are libc6-dev and any of its dependents, under >>>>> Ubuntu linux-libc-dev >>>>> >>>>> If an alternate ethernet connection is available, $ apt-get update >>>>> $ apt-get -s install linux-kernel-devel will install needed >>>>> packages. >>>>> For Debian/Ubuntu related distributions, run the following command >>>>> to display the needed package list: >>>>> >>>>> Otherwise packages have to be found through >>>>> http://packages.ubuntu.com Once downloaded and transferred into a >>>>> Linux partition, they can be installed alltogether with: >>>>> $ sudo dpkg -i *.deb >>>>> >>>>> >>>>> Checking pppd properties: >>>>> -rwsr-xr-- 1 root dip 274760 28. Nov 2008 /usr/sbin/pppd >>>>> >>>>> In case of an "error 17" "serial loopback" problem, see: >>>>> >>>>> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.ht >>>>> ml >>>>> >>>>> To enable dialout without Root permission do: >>>>> $ su - root (not for Ubuntu) >>>>> chmod a+x /usr/sbin/pppd >>>>> or under Ubuntu related Linuxes >>>>> chmod a+x /usr/sbin/pppd >>>>> >>>>> Checking settings of: /etc/ppp/options >>>>> asyncmap 0 >>>>> auth >>>>> crtscts >>>>> lock >>>>> hide-password >>>>> modem >>>>> proxyarp >>>>> lcp-echo-interval 30 >>>>> lcp-echo-failure 4 >>>>> noipx >>>>> >>>>> In case of a message like: >>>>> Warning: Could not modify /etc/ppp/pap-secrets: Permission >>>>> denied see >>>>> http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html >>>>> >>>>> For guidance on FAX usage, get from >>>>> http://linmodems.technion.ac.il/packages/ get faxing.tar.gz It has >>>>> samples for a modem using port /dev/ttySL0, which must be changed >>>> to >>>>> match your modem's port. >>>>> >>>>> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 >>>>> eth1 Which can interfere with Browser naviagation. >>>>> >>>>> Don't worry about the following, it is for experts should trouble >>>> shooting >>>>> be necessary. >>>>> ========================================================== >>>>> >>>>> Checking for modem support lines: >>>>> -------------------------------------- >>>>> /device/modem symbolic link: lrwxrwxrwx 1 root root 12 8. Mär >>>> 17:46 >>>>> /dev/modem -> /dev/ttyAGS3 >>>>> slmodemd created symbolic link /dev/ttySL0: >>>>> Within /etc/udev/ files: >>>>> >>>>> Within /etc/modprobe.conf files: >>>>> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2 >>>>> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2 >>>>> /etc/modprobe.d/alsa-base-blacklist.conf:# Uncomment these entries >>>>> in >>>> order >>>>> to blacklist unwanted modem drivers >>>>> /etc/modprobe.d/alsa-base-blacklist.conf:# blacklist >>>>> snd-atiixp-modem /etc/modprobe.d/alsa-base-blacklist.conf:# blacklist snd-via82xx-modem >>>>> Within any ancient /etc/devfs files: >>>>> >>>>> Within ancient kernel 2.4.n /etc/module.conf files: >>>>> >>>>> --------- end modem support lines -------- >>>>> >>>>> For Debian users, the linux-headers-2.6.32.6.deb can be used >>>>> instead of kernel-source/ >>>>> >>>>> >>>> >>>> >>> >>> >> >> > > >
