Ankur, Congratulations for working it through. Yours is the first reported success under a Ubuntu 2.6.28, kernel 2.6.28-11-generic of the HDA card hosted modem Codec: Motorola Si3054 Vendor Id: 0x10573055 We may later ask you to run some diagnostics for us. gnomePPP is just a graphical front end to wvdial. But it writes its setup configuration file to a hidden file in your home folder. something like .wvdialconf After running its seup Display it with: $ ls -a ./wv* You may have to enter manually the: Carrier Check = no If you have trouble using it, just back to using the command line wvdial. You will still have to do the slmodemd setup command. MarvS On Sun, Sep 20, 2009 at 4:31 AM, Ankur Joshi <pharmankur@xxxxxxxxx> wrote: > Dear MArvin, Antonio, Aelmahmody > > My wvdial.conf now looks like ---> > > [Dialer Defaults] > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90 > Modem Type = Analog Modem > ISDN = 0 > New PPPD = yes > Phone = 172222 > Modem = /dev/ttySL0 > Username = @#$#@$%$# > Carrier Check = no > Password = #@#$%^$ > Baud = 460800 > > __________________________________________________ > > > > then i did --> > > ankur@ankur:~$ grep -rsl slmodemd /etc/* > /etc/default/sl-modem-daemon > /etc/init.d/sl-modem-daemon > /etc/passwd > /etc/rc0.d/K12sl-modem-daemon > /etc/rc1.d/K12sl-modem-daemon > /etc/rc2.d/S12sl-modem-daemon > /etc/rc3.d/S12sl-modem-daemon > /etc/rc4.d/S12sl-modem-daemon > /etc/rc5.d/S12sl-modem-daemon > /etc/rc6.d/K12sl-modem-daemon > ankur@ankur:~$ sudo apt-get remove sl-modem-daemon > Reading package lists... Done > Building dependency tree > Reading state information... Done > Package sl-modem-daemon is not installed, so not removed > The following packages were automatically installed and are no longer required: > libarts1c2a libartsc0 linux-headers-2.6.27-7 liboggz1 libmagick++10 > linux-headers-2.6.28-11 ttf-kannada-fonts linux-headers-2.6.27-7-generic > amarok-common kdebase-workspace-libs4+5 libaccess-bridge-java librasqal0 > python-serial libx264-59 linux-headers-2.6.28-11-generic python-qt4-dbus > ttf-telugu-fonts libpigment0.3-5 libtunepimp5 libifp4 libpackagekit8 > libdvdread3 libffcall1 thunderbird-locale-ja ttf-oriya-fonts > gnustep-back-common ttf-bengali-fonts > Use 'apt-get autoremove' to remove them. > 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. > ankur@ankur:~$ > > > _______________________________________ > > > after reboot > i did ifconfig; down eth0 & eth1 > then sudo slmodemd -c INDIA --alsa hw:0,6 (with added space as told > by aelmahmoudy) > & after that did sudo wvdomem > > ankur@ankur:~$ ifconfig > eth0 Link encap:Ethernet HWaddr 00:1b:38:a1:94:62 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > Interrupt:19 > > eth1 Link encap:Ethernet HWaddr 00:21:00:27:6c:dc > inet6 addr: fe80::221:ff:fe27:6cdc/64 Scope:Link > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) > Interrupt:17 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:86 errors:0 dropped:0 overruns:0 frame:0 > TX packets:86 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:7158 (7.1 KB) TX bytes:7158 (7.1 KB) > > ankur@ankur:~$ sudo ifconfig eth0 down > [sudo] password for ankur: > ankur@ankur:~$ sudo ifconfig eth1 down > ankur@ankur:~$ ifconfig > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:94 errors:0 dropped:0 overruns:0 frame:0 > TX packets:94 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:7766 (7.7 KB) TX bytes:7766 (7.7 KB) > > ankur@ankur:~$ sudo slmodemd -c INDIA --alsa hw:0,6 > error: alsa setup: cannot open playback device 'hw:0,6': Device or resource busy > error: cannot setup device `hw:0,6' > ankur@ankur:~$ sudo wvdial > --> WvDial: Internet dialer version 1.60 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90 > ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90 > OK > --> Modem initialized. > --> Sending: ATDT172222 > --> Waiting for carrier. > ATDT172222 > CONNECT 46667 > --> Carrier detected. Waiting for prompt. > Welcome to UTStarcom Total Control HiPer ARC (TM) > Networks That Go The Distance (TM) > login: > --> Looks like a login prompt. > --> Sending: 2025464189 > 2025464189 > Password: > --> Looks like a password prompt. > --> Sending: (password) > ~[7f]}#@!}!}!} }?}!}$}%j}"}&[7f][7f][7f][7f]}%}&},Nvf}'}"}(}"}1}$}%j}3}#} ,w~ > --> PPP negotiation detected. > --> Starting pppd at Sun Sep 20 13:37:53 2009 > --> Pid of pppd: 4456 > --> Using interface ppp0 > --> pppd: �W� (`� > --> pppd: �W� (`� > --> pppd: �W� (`� > --> local IP address 61.2.59.110 > --> pppd: �W� (`� > --> remote IP address 61.1.96.84 > --> pppd: �W� (`� > --> primary DNS address 218.248.240.208 > --> pppd: �W� (`� > --> secondary DNS address 218.248.240.135 > --> pppd: �W� (`� > > ______________________________________________ > > then cursor kept blinking > so i thought there is successful connection > > and opened firefox typed www.google.com > > AND SOMEHOW IT IS DONE !!!!!!!! > > sudo slmodemd -c INDIA --alsa hw:0,6 is still not showing success but > net is connected now. > > > THANK YOU ALL >>>>> > Realy feeling GR8 ...... > > Thank you ... > > > One more help pls .... tell me how to use Genome PPP > Or give me the steps which command i need to give next time ??? Do i > need to repeat all this stuff each time ???? > > Regards, > > Ankur Joshi > (now online from dialup through UBUNTU ...) > > > > > On Sat, Sep 19, 2009 at 11:42 AM, أحمد المحمودي > <aelmahmoudy@xxxxxxxxxxxxxxxxxxxxx> wrote: >> On Fri, Sep 18, 2009 at 05:50:10PM -0400, Marvin Stodolsky wrote: >>> Then upon reboot, slmodemd setup will not be automatic, and >>> $ sudo slmodemd -c INDIA--alsa hw:0,6 >>> should succeed >> ---end quoted text--- >> >> I think there should be a space before --alsa: >> >> $ sudo slmodemd -c INDIA --alsa hw:0,6 >> >> -- >> أحمد المحمودي (Ahmed El-Mahmoudy) >> Digital design engineer >> GPG KeyID: 0xEDDDA1B7 (@ subkeys.pgp.net) >> GPG Fingerprint: 8206 A196 2084 7E6D 0DF8 B176 BC19 6A94 EDDD A1B7 >> >
