Marv, It seems to be an timer or usb issue. Now, I can reproduce the situation. At boot appears these messages: usb 5-2: device not accepting address 2, error -71 hub 5-0:1.0: unable to enumerate USB device on port 2 usb 5-2: new full speed USB device using uhci_hcd and address 4 usb 5-2: configuration #1 chosen from 1 choice If i dial, it won't work. At reconnection the modem in the usb port appears these messages: usbcore: deregistering interface driver ST7554 USB Modem usb 5-2: USB disconnect, address 4 usb 5-2: new full speed USB device using uhci_hcd and address 5 usb 5-2: configuration #1 chosen from 1 choice It won't work at all. I tried to suspend and resume the modem. $ i=/sys/bus/usb/devices/5-2/power; sudo sh -c "echo suspend > $i/level; echo 0 > $i/autosuspend; echo auto > $i/level" After some time spend on retrying reconnection and suspend/resume the modem connects. If it connects, then i can dial or redial like in i386, without any problems, until reboot. The curios is, if i start mprime before dialing, it seems to connect with less retries. Regards, Sebastian Am Sonntag, den 21.12.2008, 20:14 -0500 schrieb Marvin Stodolsky: > Sebastian, > > Carrier Check = mp > is likely my typo. It should be > Carrier Check = no > > All you have done seems OK technically. > It seems that the "Carrier Check = no" is being ignored, > though I don't know what to do about it. > > Giuseppe > Any suggestions? > > MarvS > > > On Sun, Dec 21, 2008 at 3:38 PM, Sebastian Felber <sf-freital@xxxxxx> wrote: > > Me too. slusb64bit.txt says: Carrier Check = mp > > Trie'd both, don't works. > > > > Sebastian > > > > Am Sonntag, den 21.12.2008, 10:51 -0500 schrieb Marvin Stodolsky: > >> RE: > Carrier Check = mp > >> Don't know what mp does. Recheck with: > >> Carrier Check = no > >> > >> MarvS > >> > >> On Sun, Dec 21, 2008 at 10:37 AM, Sebastian Felber <sf-freital@xxxxxx> wrote: > >> > Hi, > >> > > >> > I did as you said and used the slusb64bit-2.9.11-20070813.tar.gz on > >> > 2.6.24-19-generic kernel. > >> > > >> > Here are the outputs. > >> > > >> > $ sudo modprobe slusb debug=3 > >> > [ 1888.421290] Symbol usb_register_driver is being used by a non-GPL > >> > module, which will not be allowed in the future > >> > [ 1888.421295] Please see the file > >> > Documentation/feature-removal-schedule.txt in the kernel > >> > source tree for more details. > >> > [ 1888.421393] Symbol usb_deregister is being used by a non-GPL module, > >> > which will not be allowed in the future > >> > [ 1888.421395] Please see the file > >> > Documentation/feature-removal-schedule.txt in the kernel > >> > source tree for more details. > >> > [ 1888.422569] ST7554 USB Modem. > >> > [ 1888.440614] <6>slusb: slusb0 is found. > >> > [ 1888.440640] usbcore: registered new interface driver ST7554 USB Modem > >> > > >> > $ sudo slmodemd -d1 -c GERMANY /dev/slusb0 > >> > > >> > $ sudo wvdialconf wvtest > >> > Editing `wvtest'. > >> > > >> > Scanning your serial ports for a modem. > >> > > >> > Modem Port Scan<*1>: S0 S1 S2 S3 > >> > WvModem<*1>: Cannot get information for serial port. > >> > ttySL0<*1>: ATQ0 V1 E1 -- OK > >> > ttySL0<*1>: ATQ0 V1 E1 Z -- OK > >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK > >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > >> > ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem > >> > ttySL0<*1>: Speed 4800: AT -- OK > >> > ttySL0<*1>: Speed 9600: AT -- OK > >> > ttySL0<*1>: Speed 19200: AT -- OK > >> > ttySL0<*1>: Speed 38400: AT -- OK > >> > ttySL0<*1>: Speed 57600: AT -- OK > >> > ttySL0<*1>: Speed 115200: AT -- OK > >> > ttySL0<*1>: Speed 230400: AT -- OK > >> > ttySL0<*1>: Speed 460800: AT -- OK > >> > ttySL0<*1>: Max speed is 460800; that should be safe. > >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > >> > > >> > Found a modem on /dev/ttySL0. > >> > Modem configuration written to wvtest. > >> > ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > >> > > >> > $ modified wvtest > >> > [Dialer Defaults] > >> > Init1 = ATZ > >> > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> > Modem Type = Analog Modem > >> > ISDN = 0 > >> > Modem = /dev/ttySL0 > >> > Baud = 460800 > >> > Carrier Check = mp > >> > Phone = 01920782 > >> > Username = arcor > >> > Password = internet > >> > > >> > $ sudo wvdial --config=wvtest > >> > --> WvDial: Internet dialer version 1.60 > >> > --> Cannot get information for serial port. > >> > --> Initializing modem. > >> > --> Sending: ATZ > >> > ATZ > >> > OK > >> > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > >> > OK > >> > --> Modem initialized. > >> > --> Sending: ATDT01920782 > >> > --> Waiting for carrier. > >> > ATDT01920782 > >> > --> Timed out while dialing. Trying again. > >> > --> Sending: ATDT01920782 > >> > --> Waiting for carrier. > >> > NO CARRIER > >> > ATDT01920782 > >> > --> No Carrier! Trying again. > >> > --> Sending: ATDT01920782 > >> > --> Waiting for carrier. > >> > NO CARRIER > >> > ATDT01920782 > >> > --> No Carrier! Trying again. > >> > --> Sending: ATDT01920782 > >> > --> Waiting for carrier. > >> > NO CARRIER > >> > until i press CTRL-C > >> > > >> > and the debug output of slmodemd > >> > <126.525061> main: termios changed. > >> > <126.525068> slusb0: update termios... > >> > <126.525073> main: pty closed. > >> > <250.524864> main: termios changed. > >> > <250.524880> slusb0: update termios... > >> > <250.524981> slusb0: run cmd: ATZ > >> > <250.524991> slusb0: modem reset... > >> > <250.524994> slusb0: modem set state: 1 --> 1... > >> > <250.524999> slusb0: modem set mode: -> 0... > >> > <250.525004> slusb0: modem report result: 0 (OK) > >> > <250.624986> slusb0: run cmd: ATQ0V1E1S0=0&C1&D2+FCLASS=0 > >> > <250.624997> slusb0: modem set mode: -> 0... > >> > <250.625008> slusb0: modem report result: 0 (OK) > >> > <250.724968> slusb0: run cmd: ATDT01920782 > >> > <250.724973> slusb0: modem dial: T01920782... > >> > <250.724978> slusb0: modem_dial_start... > >> > <250.724994> slusb0: modem_start.. > >> > <250.725006> slusb0: modem set state: 1 --> 2... > >> > <250.725011> slusb0: new state: DP_ESTAB > >> > <250.725013> main: modemap_ioctl: cmd 8, arg 3... > >> > <250.725034> slusb0: modem set hook: 0 --> 1... > >> > <250.725043> main: modemap_ioctl: cmd 2, arg 1... > >> > <250.726210> main: modemap_ioctl: cmd 11, arg 0... > >> > <250.726245> main: modemap_ioctl: cmd 4, arg 2580... > >> > <250.726254> main: modemap_ioctl: cmd 7, arg 30... > >> > <250.726260> main: modemap_start... > >> > > >> > <--- if it work comes something like this > >> > change dp ---> 8 > >> > change dp ---> 90 > >> > <--- and other stuff > >> > > >> > <310.184884> slusb0: modem_tty_write: hangup... > >> > <310.184898> slusb0: modem_hup... > >> > <310.184901> slusb0: modem set state: 2 --> 9... > >> > <310.184904> slusb0: new state: DP_DISC > >> > <310.189619> slusb0: modem_stop.. > >> > <310.189625> main: modemap_stop... > >> > <310.192619> slusb0: modem set hook: 1 --> 0... > >> > <310.192637> main: modemap_ioctl: cmd 2, arg 0... > >> > <310.193601> main: modemap_ioctl: cmd 8, arg 0... > >> > <310.193622> slusb0: modem set state: 9 --> 1... > >> > <310.193626> slusb0: new state: MODEM_IDLE > >> > <310.193629> slusb0: modem report result: 3 (NO CARRIER) > >> > <310.193743> slusb0: run cmd: ATDT01920782 > >> > <310.193748> slusb0: modem dial: T01920782... > >> > <310.193751> slusb0: modem_dial_start... > >> > <310.193765> slusb0: modem_start.. > >> > <310.193767> slusb0: modem set state: 1 --> 2... > >> > <310.193770> slusb0: new state: DP_ESTAB > >> > <310.193773> main: modemap_ioctl: cmd 8, arg 3... > >> > <310.193783> slusb0: modem set hook: 0 --> 1... > >> > <310.193786> main: modemap_ioctl: cmd 2, arg 1... > >> > <310.194600> main: modemap_ioctl: cmd 11, arg 0... > >> > <310.194629> main: modemap_ioctl: cmd 4, arg 2580... > >> > <310.194634> main: modemap_ioctl: cmd 7, arg 30... > >> > <310.194639> main: modemap_start... > >> > <310.492880> slusb0: modem_tty_write: hangup... > >> > <310.492895> slusb0: modem_hup... > >> > <310.492899> slusb0: modem set state: 2 --> 9... > >> > <310.492903> slusb0: new state: DP_DISC > >> > <310.494635> slusb0: modem_stop.. > >> > <310.494643> main: modemap_stop... > >> > <310.498637> slusb0: modem set hook: 1 --> 0... > >> > <310.498649> main: modemap_ioctl: cmd 2, arg 0... > >> > <310.499621> main: modemap_ioctl: cmd 8, arg 0... > >> > <310.499642> slusb0: modem set state: 9 --> 1... > >> > <310.499652> slusb0: new state: MODEM_IDLE > >> > <310.499655> slusb0: modem report result: 3 (NO CARRIER) > >> > and so on. > >> > > >> > Regards, > >> > > >> > Sebastian > >> > > >> > > > > >
