Sebastian, Carrier Check = mp is likely my typo. It should be Carrier Check = no All you have done seems OK technically. It seems that the "Carrier Check = no" is being ignored, though I don't know what to do about it. Giuseppe Any suggestions? MarvS On Sun, Dec 21, 2008 at 3:38 PM, Sebastian Felber <sf-freital@xxxxxx> wrote: > Me too. slusb64bit.txt says: Carrier Check = mp > Trie'd both, don't works. > > Sebastian > > Am Sonntag, den 21.12.2008, 10:51 -0500 schrieb Marvin Stodolsky: >> RE: > Carrier Check = mp >> Don't know what mp does. Recheck with: >> Carrier Check = no >> >> MarvS >> >> On Sun, Dec 21, 2008 at 10:37 AM, Sebastian Felber <sf-freital@xxxxxx> wrote: >> > Hi, >> > >> > I did as you said and used the slusb64bit-2.9.11-20070813.tar.gz on >> > 2.6.24-19-generic kernel. >> > >> > Here are the outputs. >> > >> > $ sudo modprobe slusb debug=3 >> > [ 1888.421290] Symbol usb_register_driver is being used by a non-GPL >> > module, which will not be allowed in the future >> > [ 1888.421295] Please see the file >> > Documentation/feature-removal-schedule.txt in the kernel >> > source tree for more details. >> > [ 1888.421393] Symbol usb_deregister is being used by a non-GPL module, >> > which will not be allowed in the future >> > [ 1888.421395] Please see the file >> > Documentation/feature-removal-schedule.txt in the kernel >> > source tree for more details. >> > [ 1888.422569] ST7554 USB Modem. >> > [ 1888.440614] <6>slusb: slusb0 is found. >> > [ 1888.440640] usbcore: registered new interface driver ST7554 USB Modem >> > >> > $ sudo slmodemd -d1 -c GERMANY /dev/slusb0 >> > >> > $ sudo wvdialconf wvtest >> > Editing `wvtest'. >> > >> > Scanning your serial ports for a modem. >> > >> > Modem Port Scan<*1>: S0 S1 S2 S3 >> > WvModem<*1>: Cannot get information for serial port. >> > ttySL0<*1>: ATQ0 V1 E1 -- OK >> > ttySL0<*1>: ATQ0 V1 E1 Z -- OK >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> > ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem >> > ttySL0<*1>: Speed 4800: AT -- OK >> > ttySL0<*1>: Speed 9600: AT -- OK >> > ttySL0<*1>: Speed 19200: AT -- OK >> > ttySL0<*1>: Speed 38400: AT -- OK >> > ttySL0<*1>: Speed 57600: AT -- OK >> > ttySL0<*1>: Speed 115200: AT -- OK >> > ttySL0<*1>: Speed 230400: AT -- OK >> > ttySL0<*1>: Speed 460800: AT -- OK >> > ttySL0<*1>: Max speed is 460800; that should be safe. >> > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> > >> > Found a modem on /dev/ttySL0. >> > Modem configuration written to wvtest. >> > ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" >> > >> > $ modified wvtest >> > [Dialer Defaults] >> > Init1 = ATZ >> > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> > Modem Type = Analog Modem >> > ISDN = 0 >> > Modem = /dev/ttySL0 >> > Baud = 460800 >> > Carrier Check = mp >> > Phone = 01920782 >> > Username = arcor >> > Password = internet >> > >> > $ sudo wvdial --config=wvtest >> > --> WvDial: Internet dialer version 1.60 >> > --> Cannot get information for serial port. >> > --> Initializing modem. >> > --> Sending: ATZ >> > ATZ >> > OK >> > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> > OK >> > --> Modem initialized. >> > --> Sending: ATDT01920782 >> > --> Waiting for carrier. >> > ATDT01920782 >> > --> Timed out while dialing. Trying again. >> > --> Sending: ATDT01920782 >> > --> Waiting for carrier. >> > NO CARRIER >> > ATDT01920782 >> > --> No Carrier! Trying again. >> > --> Sending: ATDT01920782 >> > --> Waiting for carrier. >> > NO CARRIER >> > ATDT01920782 >> > --> No Carrier! Trying again. >> > --> Sending: ATDT01920782 >> > --> Waiting for carrier. >> > NO CARRIER >> > until i press CTRL-C >> > >> > and the debug output of slmodemd >> > <126.525061> main: termios changed. >> > <126.525068> slusb0: update termios... >> > <126.525073> main: pty closed. >> > <250.524864> main: termios changed. >> > <250.524880> slusb0: update termios... >> > <250.524981> slusb0: run cmd: ATZ >> > <250.524991> slusb0: modem reset... >> > <250.524994> slusb0: modem set state: 1 --> 1... >> > <250.524999> slusb0: modem set mode: -> 0... >> > <250.525004> slusb0: modem report result: 0 (OK) >> > <250.624986> slusb0: run cmd: ATQ0V1E1S0=0&C1&D2+FCLASS=0 >> > <250.624997> slusb0: modem set mode: -> 0... >> > <250.625008> slusb0: modem report result: 0 (OK) >> > <250.724968> slusb0: run cmd: ATDT01920782 >> > <250.724973> slusb0: modem dial: T01920782... >> > <250.724978> slusb0: modem_dial_start... >> > <250.724994> slusb0: modem_start.. >> > <250.725006> slusb0: modem set state: 1 --> 2... >> > <250.725011> slusb0: new state: DP_ESTAB >> > <250.725013> main: modemap_ioctl: cmd 8, arg 3... >> > <250.725034> slusb0: modem set hook: 0 --> 1... >> > <250.725043> main: modemap_ioctl: cmd 2, arg 1... >> > <250.726210> main: modemap_ioctl: cmd 11, arg 0... >> > <250.726245> main: modemap_ioctl: cmd 4, arg 2580... >> > <250.726254> main: modemap_ioctl: cmd 7, arg 30... >> > <250.726260> main: modemap_start... >> > >> > <--- if it work comes something like this >> > change dp ---> 8 >> > change dp ---> 90 >> > <--- and other stuff >> > >> > <310.184884> slusb0: modem_tty_write: hangup... >> > <310.184898> slusb0: modem_hup... >> > <310.184901> slusb0: modem set state: 2 --> 9... >> > <310.184904> slusb0: new state: DP_DISC >> > <310.189619> slusb0: modem_stop.. >> > <310.189625> main: modemap_stop... >> > <310.192619> slusb0: modem set hook: 1 --> 0... >> > <310.192637> main: modemap_ioctl: cmd 2, arg 0... >> > <310.193601> main: modemap_ioctl: cmd 8, arg 0... >> > <310.193622> slusb0: modem set state: 9 --> 1... >> > <310.193626> slusb0: new state: MODEM_IDLE >> > <310.193629> slusb0: modem report result: 3 (NO CARRIER) >> > <310.193743> slusb0: run cmd: ATDT01920782 >> > <310.193748> slusb0: modem dial: T01920782... >> > <310.193751> slusb0: modem_dial_start... >> > <310.193765> slusb0: modem_start.. >> > <310.193767> slusb0: modem set state: 1 --> 2... >> > <310.193770> slusb0: new state: DP_ESTAB >> > <310.193773> main: modemap_ioctl: cmd 8, arg 3... >> > <310.193783> slusb0: modem set hook: 0 --> 1... >> > <310.193786> main: modemap_ioctl: cmd 2, arg 1... >> > <310.194600> main: modemap_ioctl: cmd 11, arg 0... >> > <310.194629> main: modemap_ioctl: cmd 4, arg 2580... >> > <310.194634> main: modemap_ioctl: cmd 7, arg 30... >> > <310.194639> main: modemap_start... >> > <310.492880> slusb0: modem_tty_write: hangup... >> > <310.492895> slusb0: modem_hup... >> > <310.492899> slusb0: modem set state: 2 --> 9... >> > <310.492903> slusb0: new state: DP_DISC >> > <310.494635> slusb0: modem_stop.. >> > <310.494643> main: modemap_stop... >> > <310.498637> slusb0: modem set hook: 1 --> 0... >> > <310.498649> main: modemap_ioctl: cmd 2, arg 0... >> > <310.499621> main: modemap_ioctl: cmd 8, arg 0... >> > <310.499642> slusb0: modem set state: 9 --> 1... >> > <310.499652> slusb0: new state: MODEM_IDLE >> > <310.499655> slusb0: modem report result: 3 (NO CARRIER) >> > and so on. >> > >> > Regards, >> > >> > Sebastian >> > >> > > >
