Derek, Please send to the List, not directly to me, as I'm not online much.Below is a typical wvdial.conf for usage with slmodemd servicedmodems. Compare with yours. With respect to the PCMCIA card, I don't recognize Manufacture 0279.RE: Modem interrupt assignment and sharing: 11: 20570 XT-PIC-XT uhci_hcd:usb1, uhci_hcd:usb2,yenta, yenta, Intel 82801CA-ICH3, eth0, Intel 82801CA-ICH3 ModelT--------Try freeing up resources with by detaching all USB devices.# sudo ifconfig eth0 down# sudo modprobe -r snd-intel*x0m Watch kernel messages with:$ sudo tail -f /var/log/messages &Remove the PCMCIA card. Wait a few seconds and put it back in. Somechipset identifiers may be output. Also see if the card may now be detected with:$ sudo wvdialconf wvtest MarvS [Dialer defaults]# are comment linesModem = /dev/ttySL0Baud = 115200Init1 = ATZInit2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0## for noisy lines try instead# Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +MS=34ISDN = 0Modem Type = Analog ModemPhone = 3015560020Username = LoginName@xxxxxxxxxxxxxxxxxxxxxxxx = LoginPassword# needed for /dev/pts/N type portsCarrier Check = no 2008/11/22 王伟超 <derek_maxport@xxxxxxxxxxx>:> Hello Marvin,>> Thanks for your help!>> Under your help, I came out with some result when doing wvdial.>>> root@ubuntu:/#>> root@ubuntu:/media/disk/SLMODEMD.gcc4.3# gedit /etc/wvdial.conf>> root@ubuntu:/media/disk/SLMODEMD.gcc4.3# wvdial>> --> WvDial: Internet dialer version 1.60>> --> Cannot get information for serial port.>> --> Initializing modem.>> --> Sending: ATZ>> ATZ>> OK>> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0>> OK>> --> Modem initialized.>> --> Idle Seconds = 300, disabling automatic reconnect.>> --> Sending: ATDT#777>> --> Waiting for carrier.>> ATDT#777>> NO DIALTONE>> --> No dial tone.>> --> Disconnecting at Sat Nov 22 13:05:22 2008>> root@ubuntu:/media/disk/SLMODEMD.gcc4.3#>>>> Pls kindly help me out with this problem.>> One more thing to be concerned:>> I got a PCMCIA card available on my Ubuntu. I used pccardctl indent, it> shows something about the card. But when I do wvdialconf. It cannot detect> the modem. When I open a new consule, it says "too much work for irq 3".> This PCMCIA card is inserted in slot 0. Manfid 0x0279,0x950b. When using> setserial, it shows irq 3. I guess if I allocate a right irq port for it, it> can work out. But I have no idea about it.>> Pls kindly check and inform.>> Thanks and best regards> Derek>>>> Date: Fri, 21 Nov 2008 22:00:24 -0500>> From: marvin.stodolsky@xxxxxxxxx>> To: derek.king.wang@xxxxxxxxx>> Subject: Re: ModemData.txt>> CC: discuss@xxxxxxxxxxxxx>>>> Antonio>>>> The modem does get activated at the end:>> [ 1480.462475] Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB]>> -> GSI 11 (level, low) -> IRQ 11>> [ 1480.462532] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64>> ------------>> as the rest of the diagnostics show.>>>> King,>> It is an intermal Winmodem that is being detected not your PCMCIA modem.>> It you want to use the PCMCIA, do diagnostics under Microsoft to>> identify its chipset.>>>> Incidentally, the modem driver snd-intel8x0m occassionally dies when>> loaded. It can be reactivated by unloading and reloading.>>>> $ sudo modprobe -r snd-intel8x0m>> $ sudo modprobe snd-intel8x0m>>>> MarvS>>>>>> On Fri, Nov 21, 2008 at 9:41 PM, Antonio Olivares>> <olivares14031@xxxxxxxxx> wrote:>> > King,>> >>> > There's a problem here:>> >>> > Modem Interrupt and sharing :(>> >>> > Modem interrupt assignment and sharing:>> > 11: 20570 XT-PIC-XT uhci_hcd:usb1, uhci_hcd:usb2, yenta, yenta, Intel>> > 82801CA-ICH3, eth0, Intel 82801CA-ICH3 Modem>> > --- Bootup diagnostics for card in PCI slot 00:1f.6 ---->> > [ 0.622948] PCI: 0000:00:1f.6 reg 10 io port: [0, ff]>> > [ 0.622958] PCI: 0000:00:1f.6 reg 14 io port: [0, 7f]>> > [ 0.635517] pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635522] pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635527] pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635532] pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635537] pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635542] pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635547] pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635552] pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635557] pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635562] pnp 00:08: io resource (0x4e-0x4f) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635567] pnp 00:08: io resource (0x50-0x53) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635572] pnp 00:08: io resource (0x62-0x63) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635577] pnp 00:08: io resource (0x65-0x65) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635582] pnp 00:08: io resource (0x66-0x66) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635587] pnp 00:08: io resource (0x72-0x77) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635592] pnp 00:08: io resource (0x80-0x80) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635597] pnp 00:08: io resource (0x84-0x86) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635602] pnp 00:08: io resource (0x88-0x88) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635607] pnp 00:08: io resource (0x8c-0x8e) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635612] pnp 00:08: io resource (0x90-0x9f) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635617] pnp 00:08: io resource (0xa4-0xa5) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635622] pnp 00:08: io resource (0xa8-0xa9) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635627] pnp 00:08: io resource (0xac-0xad) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635632] pnp 00:08: io resource (0xb0-0xb5) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635637] pnp 00:08: io resource (0xb8-0xb9) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635642] pnp 00:08: io resource (0xbc-0xbd) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635648] pnp 00:08: io resource (0xe0-0xef) overlaps 0000:00:1f.6 BAR>> > 0 (0x0-0xff), disabling>> > [ 0.635658] pnp 00:08: io resource (0x10-0x1f) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635663] pnp 00:08: io resource (0x24-0x25) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635668] pnp 00:08: io resource (0x28-0x29) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635673] pnp 00:08: io resource (0x2c-0x2d) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635678] pnp 00:08: io resource (0x2e-0x2f) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635683] pnp 00:08: io resource (0x30-0x31) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635688] pnp 00:08: io resource (0x34-0x35) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635693] pnp 00:08: io resource (0x38-0x39) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635698] pnp 00:08: io resource (0x3c-0x3d) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635703] pnp 00:08: io resource (0x4e-0x4f) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635708] pnp 00:08: io resource (0x50-0x53) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635713] pnp 00:08: io resource (0x62-0x63) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635718] pnp 00:08: io resource (0x65-0x65) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635723] pnp 00:08: io resource (0x66-0x66) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 0.635728] pnp 00:08: io resource (0x72-0x77) overlaps 0000:00:1f.6 BAR>> > 1 (0x0-0x7f), disabling>> > [ 2.399054] serial 0000:00:1f.6: power state changed by ACPI to D0>> > [ 2.399067] serial 0000:00:1f.6: enabling device (0000 -> 0001)>> > [ 2.399081] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 11>> > (level, low) -> IRQ 11>> > [ 2.399091] serial 0000:00:1f.6: PCI INT B disabled>> > [ 1480.459510] Intel ICH Modem 0000:00:1f.6: power state changed by ACPI>> > to D0>> > [ 1480.462475] Intel ICH Modem 0000:00:1f.6: PCI INT B -> Link[LNKB] ->>> > GSI 11 (level, low) -> IRQ 11>> > [ 1480.462532] Intel ICH Modem 0000:00:1f.6: setting latency timer to 64>> >>> > The PCI slot 00:1f.6 of the modem card may be disabled early in>> > a bootup process, but then enabled later. If modem drivers load>> > but the modem is not responsive, read DOCs/Bootup.txt about possible>> > fixes.>> > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx>> > if help is needed.>> >>> > Please do the above advice and your modem appears to be supported by>> > SLMODEMD since the device is /dev/ttySL0, but not 100% sure on this.>> >>> > 1 [Modem ]: ICH-MODEM - Intel 82801CA-ICH3 Modem>> > Intel 82801CA-ICH3 Modem at irq 11>> >>> > Modem firmware information is in /proc/asound/card1/codec97#0/mc97#1-1>> > ----------------------------------------------->> > Extended modem ID: codec=1 LIN1>> >>> > Lines in: /proc/asound/card1/codec97#0/mc97#1-1+regs>> > ------------------------------->> > 0:7c = 5349 and 0:7e = 4c27>> > are translated from hexadecimal code into the modem chip identifier:>> > SIL27>> >>> >>> > The driver snd-intel8x0m with its dependent drivers:>> > snd_intel8x0m 22412 0>> > snd_ac97_codec 111652 2 snd_intel8x0m,snd_intel8x0>> > snd_pcm 83204 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss>> > snd 63268 17>> > snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device>> > snd_page_alloc 16136 3 snd_intel8x0m,snd_intel8x0,snd_pcm>> > ---------->> > provide modem + audio support.>> >>> > Get SLMODEMD.gcc4.3.tar.gz if you have not done so, from>> >>> >>> > http://linmodems.technion.ac.il/packages/smartlink/SLMODEMD.gcc4.3.tar.gz>> >>> > extract it and follow the instructions therein.>> >>> > Report back if you run into problems.>> >>> > Regards,>> >>> > Antonio>> >>> >>> > --- On Fri, 11/21/08, King Derek <derek.king.wang@xxxxxxxxx> wrote:>> >>> >> From: King Derek <derek.king.wang@xxxxxxxxx>>> >> Subject: ModemData.txt>> >> To: discuss@xxxxxxxxxxxxx>> >> Date: Friday, November 21, 2008, 5:25 PM>> >> Dear All,>> >>>> >> I installed Ubuntu on Toshiba.I got a PCMCIA Card Modem>> >> working well>> >> under Windows, but it doenot work well under Ubuntu.>> >>>> >> The attached is my ModemData.txt I got from scanModem.>> >>>> >> Pls kindly check and help me out.>> >>>> >> Thanks and best regards>> >> Derek>> >>> >>> >>> >>>> ________________________________> 更多热辣资讯尽在新版MSN首页！ 立刻访问！
