Hi Antonio and thank you for your reply,
the access denied stuff is there because I didn't run lspci with root
privileges. Running it as root or with sudo results in the following output:
05:04.0 Communication controller: Agere Systems LT WinModem (rev 02)
Subsystem: Agere Systems LT WinModem
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0a00000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 11a0 [size=8]
Region 2: I/O ports at 1000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
I've attached a new lspci.txt file to this post with the complete output
of "sudo lscpi -vv". I had more success this time. I built the
martian_modem driver and it seems to recognize the modem. I can't
establish a connection however even though the modem can connect to
parsonline (that is my provider) but the subsequent authentification
fails even though it works on windows. I use exactly the same username
and password as I do on windoze. May it have something to do with the
--country switch passed to martian_modem? There is no option for iran so
I just didn't pass any country code to it. Why isn't IR on the list
anyway? We have a lot of modem users here. Actually more than in the
whole rest of the middle east combined!
Here is the output of wvdialconf:
root@ubuntu-box:/home/momesana/projects/PDFViewer# wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT9718100
--> Waiting for carrier.
ATDT9718100
CONNECT 48000 V44
--------------------------------------------------------------
Authorised access only
This system is the property of Parsonline network
Disconnect IMMEDIATELY if you are not an authorised user!
All Activities will be logged and monitored
---------------------------------------------------------------
User Access Verification
Username:
--> Carrier detected. Waiting for prompt.
Username:
--> Looks like a login prompt.
--> Sending: p207684361**** (I've replaced the last 4 digits with
asteriscs here)
p207684361****
Password:
--> Looks like a password prompt.
--> Sending: (password)
% Authentication failed.
Username:
--> Looks like a login prompt.
--> Sending: p207684361****
p207684361****
Password:
--> Looks like a password prompt.
--> Sending: (password)
% Authentication failed.
NO CARRIER
--> Disconnecting at Fri Oct 24 22:21:14 2008
and here is the content of wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Baud = 460800
New PPPD = yes
Modem = /dev/ttySM0
ISDN = 0
Carrier Check = no
Phone = 9718100
Username = I won't tell ya that
Password = I won't tell ya that either ;)
Any ideas what I'm doing wrong?
Kind regards
momesana
Antonio Olivares wrote:
A problem appears that the LT Modem is there? but there is an IRQ problem:
05:04.0 Memory controller: Agere Systems LT WinModem (rev 02)
Subsystem: Agere Systems LT WinModem
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 70000000 (32-bit, non-prefetchable)
[disabled] [size=64K]
Region 1: I/O ports at 10a0 [disabled] [size=8]
Region 2: I/O ports at <ignored> [disabled]
Capabilities: <access denied>
Can you try booting with acpi=off or noacpi when the computer boots
and/or check BIOS settings. The device appears to be there, but the
<access denied> denied it?
Regards,
Antonio
On Thu, Oct 23, 2008 at 10:08 AM, Mehdi Salem <momesana@xxxxxxxxxxxxxx> wrote:
Hi everybody,
well, I didn't have much luck getting the agere on-board modem of my
notebook to work (running gentoo linux), thus I've got myself a pci win
modem that I am trying to get to work on my desktop pc (running
ubuntu-8.04). The output of scanModem is not very encouraging though. lspci
reports the followig:
05:04.0 Memory controller: Agere Systems LT WinModem (rev 02)
Subsystem: Agere Systems LT WinModem
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR+
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 70000000 (32-bit, non-prefetchable) [disabled]
[size=64K]
Region 1: I/O ports at 10a0 [disabled] [size=8]
Region 2: I/O ports at <ignored> [disabled]
Capabilities: <access denied>
The sound device is an onboard intel soundchip (I also have another pci
soundcard attached to the computer):
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e04c0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
....
05:09.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24
[Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01)
Subsystem: TERRATEC Electronic GmbH Aureon 7.1 Space
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 1080 [size=32]
Region 1: I/O ports at 1000 [size=128]
Capabilities: <access denied>
I've attached both the output of lspci -vv and scanModem to this email. Any
chances to get that card to work with ubuntu?
Kind regards
momesana
Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry kernel 2.6.24-19-generic
With this Subject Line cogent experts will be alerted, and useful case
names left in the Archive.
YourCountry will enable Country specific guidance. Linux experts in
YourCountry
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup
service.
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet
Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu
4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008
scanModem update of: 2008_09_28
There are no blacklisted modem drivers in /etc/modprobe* files
Attached USB devices are:
ID 0204:6025 Chipsbank Microelectronics Co., Ltd CBM2080 Flash drive
controller
ID 046d:c50e Logitech, Inc. MX-1000 Cordless Mouse Receiver
USB modems not recognized
For candidate card in slot 00:1b.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:1b.0 8086:27d8 103c:3010 Audio device: Intel
Corporation 82801G
Modem interrupt assignment and sharing:
19: 678 0 IO-APIC-fasteoi uhci_hcd:usb3, HDA Intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[ 49.297145] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) ->
IRQ 19
[ 49.297173] PCI: Setting latency timer of device 0000:00:1b.0 to 64
===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.
The ALSA verion is 1.0.16
The modem cards detected by "aplay -l" are: None
The /proc/asound/pcm file reports:
-----------------------
00-02: ICE1724 Surrounds : ICE1724 Surround PCM : playback 3
00-01: IEC1724 IEC958 : IEC1724 IEC958 : playback 1 : capture 1
00-00: ICE1724 : ICE1724 : playback 1 : capture 1
01-00: ALC260 Analog : ALC260 Analog : playback 1 : capture 1
about /proc/asound/cards:
------------------------
0 [T71Space ]: Aureon71 - Terratec Aureon 7.1-Space
Terratec Aureon 7.1-Space at 0x1080, irq 18
1 [Intel ]: HDA-Intel - HDA Intel
HDA Intel at 0xe04c0000 irq 19
PCI slot 00:1b.0 has a High Definition Audio Card
The drivers are in the kernel modules tree at:
/lib/modules/2.6.24-19-generic/ubuntu/sound/alsa-driver/pci/hda/snd-hda-intel.ko
=== Finished firmware and bootup diagnostics, next deducing cogent software.
===
A candidate modem is not evident among the PCI devices:
------------------------------------------------
00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated
Graphics Controller (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller
(rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA
IDE Controller (rev 01)
05:04.0 Memory controller: Agere Systems LT WinModem (rev 02)
05:09.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24
[Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01)
3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit
Ethernet PCI Express (rev 01)
------------------------------------------------
with USB and bridge devices not displayed.
If your modem is connected by an external serial cable,
or mounted internally on an ISA card, scanModem would not access it.
Try with Root permission
$ sudo wvdialconf /etc/wvdial.conf
to detect these modem types and some USB modems.
If the detection is successful, read the DOCs/wvdial.txt .
Edit the /etc/wvdial.conf with Root permission:
sudo gedit /etc/wvdial.conf
will be able to dial out with Root permission:
sudo wvdial
Many modems for which scanModem fails have Conexant chips.
From http://www.linuxant.com/drivers/modemident.php
get the ListModem tool, which will report on Conexant chipset modems
If the above tests fail, please provide any independent information
available on your modem.
If an alternative boot into Microsoft windows can be done, do mouse
clicks on:
Start > Settings > Control Panel > Classical View (for Window XP) > System
Hardware > Device Manager > Modems > Click on the + > Modem. Double click
to
expand the graphic. Manufacturer information may be displayed. For example,
CXT
stands for Conexant. Click the Diagnostics Tab. Record any hardware ID or
vendor
and device information. From the Driver Details TAB, copy out the VENdor and
DEVice information.
Next do the Query Modem and record the ATI specifications displayed such as:
ATI3 - Agere SoftModem Version 2.1.22
ATI5 - 2.1.22, AMR Intel MB, AC97 ID:SIL REV:0x27
Try to identify the modem setup file, with name perhaps MODEM.INF.
If may contain chipset Vendor informaton.
The /proc/asound/ audio+modem diagostics are being copied.
Finished copy to Modem/ALSAroot.tgz
Predictive diagnostics for card in bus 00:1b.0:
Modem chipset not detected on
NAME="Audio device: Intel Corporation 82801G "
CLASS=0403
PCIDEV=8086:27d8
SUBSYS=103c:3010
IRQ=19
HDA=8086:27d8
SOFT=8086:27d8.HDA
High Definition Audio (HDA) cards MAY host a modem chip in their Subsystem,
and many are supported by the ALSA audio+modem driver snd-hda-intel
A modem was not detected on HDA card 8086:27d8.
If another modem card is present, then most likely 8086:27d8 does not host
a modem.
If another modem card has not been detected, then possibilities are:
1) A Conexant modem chip is present on 8086:27d8, as Conexant chips
are frequently not detectable by ALSA diagnostics
2) The modem may be of the older non-PCI Controller Chipset
(hardware) type.
Try detection with Root permission:
sudo wvdialconf /etc/wvdial.conf
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 103c:3010
Softmodem codec or chipset from diagnostics:
from Archives:
Support type needed or chipset:
Support can likely be achieved through two mutually exclusive alternatives:
1) The hsfmodem software for Conexant chipset modems: Read DOCs/Conexant.txt
The following ALSA alternative CANNOT work with Conexant modems.
2) An ALSA modem driver plus slmodemd. Read DOCs/Smartlink.txt for details,
and
to test get the package SLMODEMD.gcc4.2.tar.gz from:
http://linmodems.technion.ac.il/packages/smartlink/
----------------end Softmodem section --------------
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source package
with full speed enabled is available, but requires driver compiling. Read
DOCs/Conexant.txt
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find
the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the
FileName,
your KernelVersion: 2.6.24_19_generic
They can be found through
http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is
OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
Support for Conexant chips hosted on High Definition Audio cards may require
installation of additional packages, one of the alsa-driver-linuxant
packages
on http://www.linuxant.com/alsa-driver/ At the same time download the
alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
hsfmodem install, there will be a message if there is necessary installation
of
alsa-driver-linuxant
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo alsa* -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
There may a message that "Dependencies" are not satisfied. In this case the
Ubuntu/Debian packages to be installed are linux-libc-dev & libc6-dev.
Package
names may be different for other Linuxes. If not on your install CD, these
packages can be searched for at http://packages.ubuntu.com. After download,
they can be coinstalled with:
sudo dpkg -i li*.deb
Again try the alsa-driver-linuxant
There may be a message that the patch must be applied. In this case get the
ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
Under Linux, this package is unpacked with:
$ tar jxf alsa*.tar.bz2
Next the patch is applied with:
$ patch -p0 < alsa-driver-1.0.17-1.patch
See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
for details on compiling and installing replacement snd-hda-intel + its
dependent drivers.
After the installation is completed, rerun the hsfmodem installation.
Reboot and try to detect the modem with Root permission:
sudo wvdialconf /etc/wvdial.conf
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.68.00.12full_k2.6.24_19_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
Read DOCs/Conexant.txt
Writing DOCs/Conexant.txt
Writing DOCs/Smartlink.txt
============ end Smartlink section =====================
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.2.3
and the compiler used in kernel assembly: 4.2.3
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.2
linuc_headers base folder /lib/modules/2.6.24-19-generic/build
However some compilations and executable functions may need additional
files,
in the FileNames.h (so called kernel "h"eaders) collection installed in
/usr/include/ .
For martian_modem, additional required packages are needed. The also
required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at
http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of some
FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The
minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to
display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 269256 2007-10-04 23:27 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble shooting
be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to
blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub
(rev 02)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated
Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 20c0 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at e0480000 (32-bit, non-prefetchable) [size=256K]
Capabilities: <access denied>
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition
Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e04c0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port
1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port
2 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=3f, subordinate=3f, sec-latency=0
Memory behind bridge: e0500000-e07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at 2000 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 2020 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 2040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at 2060 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e04c4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01
[Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00001000-00001fff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface
Bridge (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller
(rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 20a0 [size=16]
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA
IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at 20d8 [size=8]
Region 1: I/O ports at 20f0 [size=4]
Region 2: I/O ports at 20e0 [size=8]
Region 3: I/O ports at 20f4 [size=4]
Region 4: I/O ports at 20b0 [size=16]
Capabilities: <access denied>
05:04.0 Memory controller: Agere Systems LT WinModem (rev 02)
Subsystem: Agere Systems LT WinModem
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+
Latency: 0 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 255
Region 0: Memory at 70000000 (32-bit, non-prefetchable) [disabled]
[size=64K]
Region 1: I/O ports at 10a0 [disabled] [size=8]
Region 2: I/O ports at <ignored> [disabled]
Capabilities: <access denied>
05:09.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24
[Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01)
Subsystem: TERRATEC Electronic GmbH Aureon 7.1 Space
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 1080 [size=32]
Region 1: I/O ports at 1000 [size=128]
Capabilities: <access denied>
3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit
Ethernet PCI Express (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 221
Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 20c0 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at e0480000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e04c0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 1
Link: Latency L0s <1us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x0
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 2, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41b1
Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device 3010
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=3f, subordinate=3f, sec-latency=0
Memory behind bridge: e0500000-e07fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [40] Express Root Port (Slot+) IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s unlimited, L1 unlimited
Device: Errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 2
Link: Latency L0s <256ns, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug+ Surpise+
Slot: Number 3, PowerLimit 10.000000
Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
Slot: AttnInd Unknown, PwrInd Unknown, Power-
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Address: fee0300c Data: 41b9
Capabilities: [90] Subsystem: Hewlett-Packard Company Unknown device 3010
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 4: I/O ports at 2000 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 4: I/O ports at 2020 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 19
Region 4: I/O ports at 2040 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 20
Region 4: I/O ports at 2060 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at e04c4000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: e0800000-e0afffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Subsystem: Hewlett-Packard Company Unknown device 3010
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [e0] Vendor Specific Information
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 20a0 [size=16]
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 0: I/O ports at 20d8 [size=8]
Region 1: I/O ports at 20f0 [size=4]
Region 2: I/O ports at 20e0 [size=8]
Region 3: I/O ports at 20f4 [size=4]
Region 4: I/O ports at 20b0 [size=16]
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:04.0 Communication controller: Agere Systems LT WinModem (rev 02)
Subsystem: Agere Systems LT WinModem
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0a00000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 11a0 [size=8]
Region 2: I/O ports at 1000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:09.0 Multimedia audio controller: VIA Technologies Inc. VT1720/24 [Envy24PT/HT] PCI Multi-Channel Audio Controller (rev 01)
Subsystem: TERRATEC Electronic GmbH Aureon 7.1 Space
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 1180 [size=32]
Region 1: I/O ports at 1100 [size=128]
Capabilities: [80] Power Management version 1
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
3f:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 3010
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 221
Region 0: Memory at e0500000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit+ Queue=0/3 Enable+
Address: 00000000fee0300c Data: 41e9
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
Link: Speed 2.5Gb/s, Width x1
