A heartfelt thank you to Marvin, Antonio & Bjorn for helping me to get my modem working under Linux. Best wishes to you all. Clive -----Original Message----- From: Antonio Olivares [mailto:olivares14031@xxxxxxxxx] Sent: Friday, 25 July 2008 1:34 AM To: Clive Oatley Subject: RE: Modem dials & connects, but can't browse > 1)I went to Ubuntu.com to get a fix for the sudo problem. Excellent! > > 2)Finally established a dial up connection, but still can't browse. Add the following to /etc/resolv.conf using $ sudo gedit /etc/resolv.conf from here --> primary DNS address 203.12.160.35 --> pppd: [06][08] [06][08] --> secondary DNS address 203.12.160.36 /etc/resolv.conf with these two lines nameserver 203.12.160.35 nameserver 203.12.160.36 > > 3)Have tried adding "Auto DNS = yes" to dialler defaults without > success. This has happened to me, do what is in 2), you may comment this one out with ; or # after you know that it is working :) > > 4)Any further suggestions? try to do a $ sudo ifconfig eth0 down > > 5)Also how to disconnect - is there a command & what is it? Use Keys <CTRL> + <C> , ctrl + c, combination > > Some data: > > 6) > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 Modem Type = Analog Modem > Baud = 115200 SetVolume = 1 New PPPD = yes Modem = /dev/ttyS0 ISDN = 0 > Phone = 0198333713 Password = **************** Username = *********** > Stupid Mode = 1 Auto DNS = yes > > > 7) > clive@clive-desktop:~$ sudo wvdial > --> WvDial: Internet dialer version 1.60 Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 > +FCLASS=0 > ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT0198333713 > --> Waiting for carrier. > ATDT0198333713 > CONNECT 28800/V42BIS > Unauthorised access to this computer system is prohibited User Access > Verification > Username: > --> Carrier detected. Starting PPP immediately. > --> Starting pppd at Thu Jul 24 21:49:37 2008 Pid of pppd: 6218 Using > --> interface ppp0 > --> pppd: [06][08] [06][08] > --> pppd: [06][08] [06][08] > --> pppd: [06][08] [06][08] > --> pppd: [06][08] [06][08] > --> local IP address 60.241.31.57 > --> pppd: [06][08] [06][08] > --> remote IP address 220.245.178.161 > --> pppd: [06][08] [06][08] > --> primary DNS address 203.12.160.35 > --> pppd: [06][08] [06][08] > --> secondary DNS address 203.12.160.36 > --> pppd: [06][08] [06][08] > > Thanks, > Clive Hope this helps get you online, and happily browsing :) Regards, Antonio > > -----Original Message----- > From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx] > Sent: Tuesday, 22 July 2008 10:02 PM > To: Clive Oatley > Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx > Subject: Re: Modem dials & connects, but can't browse > > These results seem OK > Not apparent what your problem is in using "sudo" > More this PM maybe. > > MarvS > > On Tue, Jul 22, 2008 at 2:52 AM, Clive Oatley <cliveoatley@xxxxxxxxx> > wrote: > > Here's the result of the two tasks you gave me: > > > > 1)clive@clive-desktop:~$ cat /etc/hostname > > > > clive-desktop > > > > 2)clive@clive-desktop:~$ grep -rs clive-desktop /etc/* > > > > /etc/hostname:clive-desktop > > /etc/hosts:127.0.1.1 clive-desktop.TPG (Marvin - > please note ".TPG" was the > problem)/etc/motd:Linux clive-desktop > > 2.6.24-16-generic #1 SMP Thu Apr 10 13:23:42 UTC 2008 > i686 > > clive@clive-desktop:~$ > > > > Clive > > > > -----Original Message----- > > From: Marvin Stodolsky > [mailto:marvin.stodolsky@xxxxxxxxx] > > Sent: Tuesday, 22 July 2008 8:05 AM > > To: Clive Oatley > > Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx > > Subject: Re: Modem dials but can't connect > > > > On my marvlap System: > > $ grep -rs marvlap /etc/* > > /etc/hostname:marvlap > > /etc/hosts:127.0.1.1 marvlap > > > > What is shown on yours by: > > $ grep -rs clive-desktop /etc/* > > > > > > MarvS > > > > On Mon, Jul 21, 2008 at 9:20 AM, Clive Oatley > <cliveoatley@xxxxxxxxx> wrote: > >> Went to make changes (semi-colon), but ran into > this problem: > >> > >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf > >> sudo: unable to resolve host clive-desktop > clive@clive-desktop:~$ > >> > >> Have tried re-booting several times (only solution > ,as non-Linux user, I could think of) without success. Do you have any > bright ideas? > >> > >> Clive > >> > >> -----Original Message----- > >> From: Marvin Stodolsky > [mailto:marvin.stodolsky@xxxxxxxxx] > >> Sent: Sunday, 20 July 2008 7:07 PM > >> To: Clive Oatley > >> Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx > >> Subject: Re: Modem dials but can't connect > >> > >> Clive, > >> > >> In your prior email, some of the lines of [Dialer > default] were terminated with a semi-colon They should be removed. Be > sure to do these edits with a simple text editor, such as gedit. > >> > >> MarvS > >> > >> > >> On Sun, Jul 20, 2008 at 3:24 AM, Clive Oatley > <cliveoatley@xxxxxxxxx> wrote: > >>> Thanks for the input Antonio. Tried your > solutions, but still get > >>> the "bad init string" message. > Couldn't turn off the dialler noise either. > >>> Frustrated, moi? > >>> > >>> Thanks again for the support, > >>> Clive > >>> > >>> -----Original Message----- > >>> From: Antonio Olivares > [mailto:olivares14031@xxxxxxxxx] > >>> Sent: Sunday, 20 July 2008 1:22 PM > >>> To: Clive Oatley > >>> Cc: discuss@xxxxxxxxxxxxx > >>> Subject: RE: Modem dials but can't connect > >>> > >>> > >>> Clive, > >>> > >>> I have had a similar problem with an external > modem. I could > >>> connect with it using slax, but not with > Fedora :( > >>> > >>> It did not allow the +MS=90 or +MS=34, but the > following strings did > >>> get through > >>> > >>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 > +MS=V90 or > >>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 > +MS=V34 > >>> > >>> There are some ppp options that do not work > together, if you have > >>> Auto DNS = yes and in /etc/resolv.conf you > have nameservers, pppd > >>> will complain :( > >>> > >>> In my /etc/pppd/options I have (copied from > slax to Fedora, fedora > >>> only had lock option ), this way I could > connect. > >>> > >>> Checking settings of: /etc/ppp/options > >>> asyncmap 0 > >>> crtscts > >>> lock > >>> modem > >>> proxyarp > >>> lcp-echo-interval 30 > >>> lcp-echo-failure 4 > >>> > >>> Now depending on what type of modem that you > have and your ISP, it > >>> might help to know which is your ISP and > determine why the > >>> connection is not going through > >>> > >>> Here's wvdial.conf for the external modem > that worked without the > >>> Init2 > >>> string: > >>> > >>> [root@localhost etc]# cat wvdial.conf > >>> > >>> > >>> [Modem0] > >>> Modem = /dev/ttyS0 > >>> Baud = 57600 > >>> SetVolume = 2 > >>> Dial Command = ATDT > >>> Init1 = ATZ > >>> Init3 = ATM1L2 > >>> FlowControl = CRTSCTS > >>> [Dialer awesomenet] > >>> Username = my_username > >>> Password = my_password > >>> Phone = 7072000 > >>> Stupid Mode = 1 > >>> Init1 = ATZ > >>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0 Inherits = Modem0 > >>> > >>> There you could see the command SetVolume = 2, > if you do not want > >>> sound you may change that to SetVolume = 0 if > it works for your modem of course. > >>> > >>> Regards, > >>> > >>> Antonio > >>> > >>>> [Dialer Defaults] > >>>> Init1 = ATZ ; > >>>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 > +FCLASS=0 Modem Type = Analog > >>>> Modem Baud = 115200 New PPPD = yes Modem = > /dev/ttyS0 ISDN = 0 > >>>> Phone = > >>>> 0198333713 ; Password = xxxxxxxxxxxx ; > Username = xxxxxxxxxxxxx; > >>>> Carrier check = no Stupid Mode = 1 > >>>> > >>>> I have tested with your suggestions & > still can't connect. Whenever > >>>> I replace "+FCLASS=0" with > "+MS=34", "+MS=NumberValue" or > "+MS=90" > >>>> I'm still getting the "bad init > string" message. > >>>> > >>>> I do appreciate the time you are giving > me. > >>>> > >>>> Clive > >>>> > >>>> -----Original Message----- > >>>> From: Marvin Stodolsky > [mailto:marvin.stodolsky@xxxxxxxxx] > >>>> Sent: Saturday, 19 July 2008 11:43 PM > >>>> To: Clive Oatley > >>>> Cc: Discuss@xxxxxxxxxxxxx > >>>> Subject: Re: Modem dials but can't > connect > >>>> > >>>> Clive, > >>>> > >>>> Please send us your /etc/wvdial.conf Just > replace your LoginName > >>>> and PassWord wth XXXXX > >>>> > >>>> For and COMMAND, you can get usage info > with $ man COMMAND > >>>> including $ man pppd > >>>> > >>>> NumberValues used with +MS= are one of 34, > 90, or 92 They specify > >>>> the max speed/compression to be used with > success depedent on line > >>>> quality. +MS=92 is the current default, > but is poorly implemented > >>>> at some IPs. > >>>> So a conservative fallback is to first > test with +MS=34 If that is > >>>> OK > >>>> +MS=90 can be tested. > >>>> > >>>> MarvS > >>>> > >>>> On Sat, Jul 19, 2008 at 3:37 AM, Clive > Oatley > >>>> <cliveoatley@xxxxxxxxx> > >>>> wrote: > >>>> > Marvin, > >>>> > Please see my explanations & > requests for > >>>> clarification to some of your suggestions > in *CAPITALS* below (Just > >>>> using capitals to differentiate between > you & me, not shouting or > >>>> flaming ;->). > >>>> > > >>>> > Also, is it possible to turn the > modem sound off as I > >>>> find the dialling noises really annoying. > >>>> > > >>>> > And finally how do you disconnect > i.e. what's the > >>>> command to disconnect once you've > successfully connected. > >>>> > > >>>> > Thanks, > >>>> > Clive > >>>> > -----Original Message----- > >>>> > From: Marvin Stodolsky > >>>> [mailto:marvin.stodolsky@xxxxxxxxx] > >>>> > Sent: Saturday, 19 July 2008 10:10 AM > >>>> > To: Clive Oatley > >>>> > Cc: Discuss@xxxxxxxxxxxxx > >>>> > Subject: Re: Modem dials but > can't connect > >>>> > > >>>> > Clive > >>>> > > >>>> > With > >>>> > $ man pppd *PLEASE ELABORATE. IS THIS > AN INSTRUCTION > >>>> FOR ME TO > >>>> > FOLLOW?* > >>>> > > >>>> > 2 An error was detected in > processing the > >>>> options given, > >>>> > such as two mutually exclusive > options being used. > >>>> *PLEASE EXPLAIN > >>>> > WHAT THE TWO MUTUALLY EXCLUSIVE > OPTIONS WERE.* > >>>> > > >>>> >> changes: +MS=34 & +MS=90 gave > "bad init > >>>> string" messages. > >>>> > Just use +MS=NumberValue once as the > last item on the > >>>> line. *SHOULD > >>>> > "number value" BE REPLACED > BY AN ACTUAL > >>>> NUMBER & IF SO WHAT WOULD BE > >>>> > A RANGE OF NUMBERS THAT WOULD BE > APPROPRIATE OR LEFT > >>>> AS > >>>> > "NumberValue"?* > >>>> > > >>>> > * I TRIED EACH SEPARATELY & BOTH > GAVE "BAD > >>>> INIT STRING" MESSAGES. I RAN ALL > WVDIAL.TXT SUGGESTIONS ONE AT A > >>>> TIME AS CHANGES TO THE DEFAULTS & IN > THESE INSTANCES,I.E. +MS=,THEY > >>>> WERE AT THE END OF THE LINE & REPLACED > "+FCLASS=0" . > >>>> > > >>>> > Re: --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 X3 ATQ0 V1 E1 > >>>> > S0=0 &C1 &D2 +FCLASS=0 X3 > >>>> > -------------- > >>>> > X3 shouldn't be last. Use: > >>>> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 > &D2 +FCLASS=0 > >>>> or > >>>> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 > &D2 +MS=34 *I > >>>> DON'T THINK I REALLY NEEDED X3, BUT > WILL TRY AGAIN WITH IT IN THE > >>>> CORRECT POSITION* > >>>> > > >>>> > RE: Sending: ATDP0198333713 > >>>> > ATDP is for older pulse dial phone > lines, If yours is > >>>> Touch Tone, use > >>>> > the default ATDT * I JUST USED THIS > (atdp) AS PART OF > >>>> THE TEST > >>>> > PROCESS. I ALSO USED THE TONE > OPTION.* > >>>> > > >>>> > You can also test adding a line Stupid Mode = 1 needed with > >>>> > some Internet Providers. > *I TRIED THIS > >>>> WITH "YES" AS PER > >>>> > THE NOTES, WILL TRY AGAIN WITH > "1"* > >>>> > > >>>> > MarvS > >>>> > > >>>> > On Fri, Jul 18, 2008 at 7:33 PM, > Clive Oatley > >>>> <cliveoatley@xxxxxxxxx> wrote: > >>>> >> I have reached the point where I > can get the modem > >>>> to dial, but it > >>>> >> fails to connect. > >>>> >> I have worked through wvdial.txt > & tried the > >>>> solutions offered there. > >>>> >> Some > >>>> >> changes: +MS=34 & +MS=90 gave > "bad init > >>>> string" messages. > >>>> >> Also, is it possible to turn of > the modem sound > >>>> off as I find the > >>>> >> dialling noises really annoying. > >>>> >> > >>>> >> See below: > >>>> >> > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> [sudo] password > >>>> >> for > >>>> >> clive: > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0 OK > >>>> >> --> Modem initialized. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDT0198333713 ; > >>>> >> OK > >>>> >> --> Timed out while dialing. > Trying again. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDT0198333713 ; > >>>> >> OK > >>>> >> Caught signal 2: Attempting to > exit gracefully... > >>>> >> --> Disconnecting at Sat Jul > 19 08:58:47 2008 > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> --> Sending: ATQ0 > >>>> >> ATQ0 > >>>> >> OK > >>>> >> --> Re-Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0 X3 OK > >>>> >> --> Modem initialized. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDT0198333713 ; > >>>> >> OK > >>>> >> --> Timed out while dialing. > Trying again. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> p > >>>> >> ATDT0198333713 ; > >>>> >> Caught signal 2: Attempting to > exit gracefully... > >>>> >> --> Disconnecting at Sat Jul > 19 09:02:43 2008 > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=34 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=34 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> --> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=34 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=34 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> --> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=34 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=34 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=90 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=90 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> --> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=90 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=90 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> --> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +MS=90 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +MS=90 X3 ERROR > >>>> >> --> Bad init string. > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 X3 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0 X3 OK > >>>> >> --> Modem initialized. > >>>> >> --> Sending: ATDP0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDP0198333713 ; > >>>> >> OK > >>>> >> --> Timed out while dialing. > Trying again. > >>>> >> --> Sending: ATDP0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> p > >>>> >> ATDP0198333713 ; > >>>> >> Caught signal 2: Attempting to > exit gracefully... > >>>> >> --> Disconnecting at Sat Jul > 19 09:08:28 2008 > >>>> >> clive@clive-desktop:~$ sudo gedit > /etc/wvdial.conf > >>>> > >>>> >> clive@clive-desktop:~$ sudo > wvdial > >>>> >> --> WvDial: Internet dialer > version 1.60 > >>>> Initializing modem. > >>>> >> --> Sending: ATZ > >>>> >> ATZ > >>>> >> OK > >>>> >> --> Sending: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 > >>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 > +FCLASS=0 OK > >>>> >> --> Modem initialized. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDT0198333713 ; > >>>> >> OK > >>>> >> --> Timed out while dialing. > Trying again. > >>>> >> --> Sending: ATDT0198333713 ; > >>>> >> --> Waiting for carrier. > >>>> >> ATDT0198333713 ; > >>>> >> OK > >>>> >> Caught signal 2: Attempting to > exit gracefully... > >>>> >> --> Disconnecting at Sat Jul > 19 09:11:35 2008 > >>>> >> clive@clive-desktop:~$ sudo > wvdialconf wvtest > >>>> Editing `wvtest'. > >>>> >> > >>>> >> Scanning your serial ports for a > modem. > >>>> >> > >>>> >> ttyS0<*1>: ATQ0 V1 E1 -- > ATQ0 V1 E1 > >>>> >> ttyS0<*1>: failed with 2400 > baud, next try: > >>>> 9600 baud > >>>> >> ttyS0<*1>: ATQ0 V1 E1 -- OK > >>>> >> ttyS0<*1>: ATQ0 V1 E1 Z -- > OK > >>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 > -- OK > >>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 > &C1 -- OK > >>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> -- OK > >>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 -- OK > >>>> >> ttyS0<*1>: Modem > Identifier: ATI -- IP568 > >>>> Data/Fax/Voice 56K Modem > >>>> >> ttyS0<*1>: Speed 19200: AT > -- OK > >>>> >> ttyS0<*1>: Speed 38400: AT > -- OK > >>>> >> ttyS0<*1>: Speed 57600: AT > -- OK > >>>> >> ttyS0<*1>: Speed 115200: AT > -- OK > >>>> >> ttyS0<*1>: Max speed is > 115200; that should > >>>> be safe. > >>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 > &C1 &D2 > >>>> +FCLASS=0 -- OK > >>>> >> Modem Port Scan<*1>: S2 > S3 > >>>> >> > >>>> >> Found a modem on /dev/ttyS0. > >>>> >> wvtest<Warn>: Can't > open > >>>> 'wvtest' for reading: No such file > or > >>>> >> directory > >>>> >> wvtest<Warn>: ...starting > with blank > >>>> configuration. > >>>> >> Modem configuration written to > wvtest. > >>>> >> ttyS0<Info>: Speed 115200; > init "ATQ0 > >>>> V1 E1 S0=0 &C1 &D2 +FCLASS=0" > >>>> >> clive@clive-desktop:~$ > >>>> >> > >>>> >> > >>>> >> > >>>> > > >>>> > > >>> > >>> > >>> > >>> > >>> > >> > >> > > > >
