Clive All other COMM channels must be shut down before you dialout, or DNSservices will be blocked. Do:$ ifconfiglo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1790 errors:0 dropped:0 overruns:0 frame:0 TX packets:1790 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:89500 (87.4 KB) TX bytes:89500 (87.4 KB) eth0 Link encap:Ethernet HWaddr 00:0f:66:f2:b1:8e inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20f:66ff:fef2:b18e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4879 errors:0 dropped:0 overruns:0 frame:0 TX packets:3041 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4363608 (4.1 MB) TX bytes:639667 (624.6 KB) lo (loopback) is OK . But any eth of wireless must be closed withcommand like: $ sudo ifconfig eth0 downof PPP will later try to use the eth0 DNSCheck with$ ifconfig WHen only lo is left. Dialout & browse. For dialout started with$ sudo wvdialClose wvdial with$ Ctrl-C MarvS On Thu, Jul 24, 2008 at 8:17 AM, Clive Oatley <cliveoatley@xxxxxxxxx> wrote:> 1)I went to Ubuntu.com to get a fix for the sudo problem.>> 2)Finally established a dial up connection, but still can't browse.>> 3)Have tried adding "Auto DNS = yes" to dialler defaults without success.>> 4)Any further suggestions?>> 5)Also how to disconnect - is there a command & what is it?>> Some data:>> 6)> Init1 = ATZ> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0> Modem Type = Analog Modem> Baud = 115200> SetVolume = 1> New PPPD = yes> Modem = /dev/ttyS0> ISDN = 0> Phone = 0198333713> Password = ****************> Username = ***********> Stupid Mode = 1> Auto DNS = yes>>> 7)> clive@clive-desktop:~$ sudo wvdial> --> WvDial: Internet dialer version 1.60> --> Initializing modem.> --> Sending: ATZ> ATZ> OK> --> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0> ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0> OK> --> Modem initialized.> --> Sending: ATDT0198333713> --> Waiting for carrier.> ATDT0198333713> CONNECT 28800/V42BIS> Unauthorised access to this computer system is prohibited> User Access Verification> Username:> --> Carrier detected. Starting PPP immediately.> --> Starting pppd at Thu Jul 24 21:49:37 2008> --> Pid of pppd: 6218> --> Using interface ppp0> --> pppd: ��[06][08] �[06][08]> --> pppd: ��[06][08] �[06][08]> --> pppd: ��[06][08] �[06][08]> --> pppd: ��[06][08] �[06][08]> --> local IP address 60.241.31.57> --> pppd: ��[06][08] �[06][08]> --> remote IP address 220.245.178.161> --> pppd: ��[06][08] �[06][08]> --> primary DNS address 203.12.160.35> --> pppd: ��[06][08] �[06][08]> --> secondary DNS address 203.12.160.36> --> pppd: ��[06][08] �[06][08]>> Thanks,> Clive>> -----Original Message-----> From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx]> Sent: Tuesday, 22 July 2008 10:02 PM> To: Clive Oatley> Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx> Subject: Re: Modem dials & connects, but can't browse>> These results seem OK> Not apparent what your problem is in using "sudo"> More this PM maybe.>> MarvS>> On Tue, Jul 22, 2008 at 2:52 AM, Clive Oatley <cliveoatley@xxxxxxxxx> wrote:>> Here's the result of the two tasks you gave me:>>>> 1)clive@clive-desktop:~$ cat /etc/hostname>>>> clive-desktop>>>> 2)clive@clive-desktop:~$ grep -rs clive-desktop /etc/*>>>> /etc/hostname:clive-desktop>> /etc/hosts:127.0.1.1 clive-desktop.TPG (Marvin - please note ".TPG" was the problem)/etc/motd:Linux clive-desktop>> 2.6.24-16-generic #1 SMP Thu Apr 10 13:23:42 UTC 2008 i686>> clive@clive-desktop:~$>>>> Clive>>>> -----Original Message----->> From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx]>> Sent: Tuesday, 22 July 2008 8:05 AM>> To: Clive Oatley>> Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx>> Subject: Re: Modem dials but can't connect>>>> On my marvlap System:>> $ grep -rs marvlap /etc/*>> /etc/hostname:marvlap>> /etc/hosts:127.0.1.1 marvlap>>>> What is shown on yours by:>> $ grep -rs clive-desktop /etc/*>>>>>> MarvS>>>> On Mon, Jul 21, 2008 at 9:20 AM, Clive Oatley <cliveoatley@xxxxxxxxx> wrote:>>> Went to make changes (semi-colon), but ran into this problem:>>>>>> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>> sudo: unable to resolve host clive-desktop clive@clive-desktop:~$>>>>>> Have tried re-booting several times (only solution ,as non-Linux user, I could think of) without success. Do you have any bright ideas?>>>>>> Clive>>>>>> -----Original Message----->>> From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx]>>> Sent: Sunday, 20 July 2008 7:07 PM>>> To: Clive Oatley>>> Cc: olivares14031@xxxxxxxxx; discuss@xxxxxxxxxxxxx>>> Subject: Re: Modem dials but can't connect>>>>>> Clive,>>>>>> In your prior email, some of the lines of [Dialer default] were terminated with a semi-colon They should be removed. Be sure to do these edits with a simple text editor, such as gedit.>>>>>> MarvS>>>>>>>>> On Sun, Jul 20, 2008 at 3:24 AM, Clive Oatley <cliveoatley@xxxxxxxxx> wrote:>>>> Thanks for the input Antonio. Tried your solutions, but still get>>>> the "bad init string" message. Couldn't turn off the dialler noise either.>>>> Frustrated, moi?>>>>>>>> Thanks again for the support,>>>> Clive>>>>>>>> -----Original Message----->>>> From: Antonio Olivares [mailto:olivares14031@xxxxxxxxx]>>>> Sent: Sunday, 20 July 2008 1:22 PM>>>> To: Clive Oatley>>>> Cc: discuss@xxxxxxxxxxxxx>>>> Subject: RE: Modem dials but can't connect>>>>>>>>>>>> Clive,>>>>>>>> I have had a similar problem with an external modem. I could>>>> connect with it using slax, but not with Fedora :(>>>>>>>> It did not allow the +MS=90 or +MS=34, but the following strings did>>>> get through>>>>>>>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=V90 or>>>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=V34>>>>>>>> There are some ppp options that do not work together, if you have>>>> Auto DNS = yes and in /etc/resolv.conf you have nameservers, pppd>>>> will complain :(>>>>>>>> In my /etc/pppd/options I have (copied from slax to Fedora, fedora>>>> only had lock option ), this way I could connect.>>>>>>>> Checking settings of: /etc/ppp/options>>>> asyncmap 0>>>> crtscts>>>> lock>>>> modem>>>> proxyarp>>>> lcp-echo-interval 30>>>> lcp-echo-failure 4>>>>>>>> Now depending on what type of modem that you have and your ISP, it>>>> might help to know which is your ISP and determine why the>>>> connection is not going through>>>>>>>> Here's wvdial.conf for the external modem that worked without the>>>> Init2>>>> string:>>>>>>>> [root@localhost etc]# cat wvdial.conf>>>>>>>>>>>> [Modem0]>>>> Modem = /dev/ttyS0>>>> Baud = 57600>>>> SetVolume = 2>>>> Dial Command = ATDT>>>> Init1 = ATZ>>>> Init3 = ATM1L2>>>> FlowControl = CRTSCTS>>>> [Dialer awesomenet]>>>> Username = my_username>>>> Password = my_password>>>> Phone = 7072000>>>> Stupid Mode = 1>>>> Init1 = ATZ>>>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Inherits = Modem0>>>>>>>> There you could see the command SetVolume = 2, if you do not want>>>> sound you may change that to SetVolume = 0 if it works for your modem of course.>>>>>>>> Regards,>>>>>>>> Antonio>>>>>>>>> [Dialer Defaults]>>>>> Init1 = ATZ ;>>>>> Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 Modem Type = Analog>>>>> Modem Baud = 115200 New PPPD = yes Modem = /dev/ttyS0 ISDN = 0>>>>> Phone =>>>>> 0198333713 ; Password = xxxxxxxxxxxx ; Username = xxxxxxxxxxxxx;>>>>> Carrier check = no Stupid Mode = 1>>>>>>>>>> I have tested with your suggestions & still can't connect. Whenever>>>>> I replace "+FCLASS=0" with "+MS=34", "+MS=NumberValue" or "+MS=90">>>>> I'm still getting the "bad init string" message.>>>>>>>>>> I do appreciate the time you are giving me.>>>>>>>>>> Clive>>>>>>>>>> -----Original Message----->>>>> From: Marvin Stodolsky [mailto:marvin.stodolsky@xxxxxxxxx]>>>>> Sent: Saturday, 19 July 2008 11:43 PM>>>>> To: Clive Oatley>>>>> Cc: Discuss@xxxxxxxxxxxxx>>>>> Subject: Re: Modem dials but can't connect>>>>>>>>>> Clive,>>>>>>>>>> Please send us your /etc/wvdial.conf Just replace your LoginName>>>>> and PassWord wth XXXXX>>>>>>>>>> For and COMMAND, you can get usage info with $ man COMMAND>>>>> including $ man pppd>>>>>>>>>> NumberValues used with +MS= are one of 34, 90, or 92 They specify>>>>> the max speed/compression to be used with success depedent on line>>>>> quality. +MS=92 is the current default, but is poorly implemented>>>>> at some IPs.>>>>> So a conservative fallback is to first test with +MS=34 If that is>>>>> OK>>>>> +MS=90 can be tested.>>>>>>>>>> MarvS>>>>>>>>>> On Sat, Jul 19, 2008 at 3:37 AM, Clive Oatley>>>>> <cliveoatley@xxxxxxxxx>>>>>> wrote:>>>>> > Marvin,>>>>> > Please see my explanations & requests for>>>>> clarification to some of your suggestions in *CAPITALS* below (Just>>>>> using capitals to differentiate between you & me, not shouting or>>>>> flaming ;->).>>>>> >>>>>> > Also, is it possible to turn the modem sound off as I>>>>> find the dialling noises really annoying.>>>>> >>>>>> > And finally how do you disconnect i.e. what's the>>>>> command to disconnect once you've successfully connected.>>>>> >>>>>> > Thanks,>>>>> > Clive>>>>> > -----Original Message----->>>>> > From: Marvin Stodolsky>>>>> [mailto:marvin.stodolsky@xxxxxxxxx]>>>>> > Sent: Saturday, 19 July 2008 10:10 AM>>>>> > To: Clive Oatley>>>>> > Cc: Discuss@xxxxxxxxxxxxx>>>>> > Subject: Re: Modem dials but can't connect>>>>> >>>>>> > Clive>>>>> >>>>>> > With>>>>> > $ man pppd *PLEASE ELABORATE. IS THIS AN INSTRUCTION>>>>> FOR ME TO>>>>> > FOLLOW?*>>>>> >>>>>> > 2 An error was detected in processing the>>>>> options given,>>>>> > such as two mutually exclusive options being used.>>>>> *PLEASE EXPLAIN>>>>> > WHAT THE TWO MUTUALLY EXCLUSIVE OPTIONS WERE.*>>>>> >>>>>> >> changes: +MS=34 & +MS=90 gave "bad init>>>>> string" messages.>>>>> > Just use +MS=NumberValue once as the last item on the>>>>> line. *SHOULD>>>>> > "number value" BE REPLACED BY AN ACTUAL>>>>> NUMBER & IF SO WHAT WOULD BE>>>>> > A RANGE OF NUMBERS THAT WOULD BE APPROPRIATE OR LEFT>>>>> AS>>>>> > "NumberValue"?*>>>>> >>>>>> > * I TRIED EACH SEPARATELY & BOTH GAVE "BAD>>>>> INIT STRING" MESSAGES. I RAN ALL WVDIAL.TXT SUGGESTIONS ONE AT A>>>>> TIME AS CHANGES TO THE DEFAULTS & IN THESE INSTANCES,I.E. +MS=,THEY>>>>> WERE AT THE END OF THE LINE & REPLACED "+FCLASS=0" .>>>>> >>>>>> > Re: --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0 X3 ATQ0 V1 E1>>>>> > S0=0 &C1 &D2 +FCLASS=0 X3>>>>> > -------------->>>>> > X3 shouldn't be last. Use:>>>>> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0>>>>> or>>>>> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=34 *I>>>>> DON'T THINK I REALLY NEEDED X3, BUT WILL TRY AGAIN WITH IT IN THE>>>>> CORRECT POSITION*>>>>> >>>>>> > RE: Sending: ATDP0198333713>>>>> > ATDP is for older pulse dial phone lines, If yours is>>>>> Touch Tone, use>>>>> > the default ATDT * I JUST USED THIS (atdp) AS PART OF>>>>> THE TEST>>>>> > PROCESS. I ALSO USED THE TONE OPTION.*>>>>> >>>>>> > You can also test adding a line>>>>> > Stupid Mode = 1>>>>> > needed with some Internet Providers. *I TRIED THIS>>>>> WITH "YES" AS PER>>>>> > THE NOTES, WILL TRY AGAIN WITH "1"*>>>>> >>>>>> > MarvS>>>>> >>>>>> > On Fri, Jul 18, 2008 at 7:33 PM, Clive Oatley>>>>> <cliveoatley@xxxxxxxxx> wrote:>>>>> >> I have reached the point where I can get the modem>>>>> to dial, but it>>>>> >> fails to connect.>>>>> >> I have worked through wvdial.txt & tried the>>>>> solutions offered there.>>>>> >> Some>>>>> >> changes: +MS=34 & +MS=90 gave "bad init>>>>> string" messages.>>>>> >> Also, is it possible to turn of the modem sound>>>>> off as I find the>>>>> >> dialling noises really annoying.>>>>> >>>>>>> >> See below:>>>>> >>>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>> [sudo] password>>>>> >> for>>>>> >> clive:>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK>>>>> >> --> Modem initialized.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDT0198333713 ;>>>>> >> OK>>>>> >> --> Timed out while dialing. Trying again.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDT0198333713 ;>>>>> >> OK>>>>> >> Caught signal 2: Attempting to exit gracefully...>>>>> >> --> Disconnecting at Sat Jul 19 08:58:47 2008>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>>>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> --> Sending: ATQ0>>>>> >> ATQ0>>>>> >> OK>>>>> >> --> Re-Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 X3 OK>>>>> >> --> Modem initialized.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDT0198333713 ;>>>>> >> OK>>>>> >> --> Timed out while dialing. Trying again.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> p>>>>> >> ATDT0198333713 ;>>>>> >> Caught signal 2: Attempting to exit gracefully...>>>>> >> --> Disconnecting at Sat Jul 19 09:02:43 2008>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>>>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=34 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=34 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> --> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=34 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=34 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> --> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=34 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=34 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>>>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=90 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=90 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> --> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=90 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=90 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> --> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +MS=90 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +MS=90 X3 ERROR>>>>> >> --> Bad init string.>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>>>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0 X3>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 X3 OK>>>>> >> --> Modem initialized.>>>>> >> --> Sending: ATDP0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDP0198333713 ;>>>>> >> OK>>>>> >> --> Timed out while dialing. Trying again.>>>>> >> --> Sending: ATDP0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> p>>>>> >> ATDP0198333713 ;>>>>> >> Caught signal 2: Attempting to exit gracefully...>>>>> >> --> Disconnecting at Sat Jul 19 09:08:28 2008>>>>> >> clive@clive-desktop:~$ sudo gedit /etc/wvdial.conf>>>>>>>>>> >> clive@clive-desktop:~$ sudo wvdial>>>>> >> --> WvDial: Internet dialer version 1.60>>>>> Initializing modem.>>>>> >> --> Sending: ATZ>>>>> >> ATZ>>>>> >> OK>>>>> >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0>>>>> >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK>>>>> >> --> Modem initialized.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDT0198333713 ;>>>>> >> OK>>>>> >> --> Timed out while dialing. Trying again.>>>>> >> --> Sending: ATDT0198333713 ;>>>>> >> --> Waiting for carrier.>>>>> >> ATDT0198333713 ;>>>>> >> OK>>>>> >> Caught signal 2: Attempting to exit gracefully...>>>>> >> --> Disconnecting at Sat Jul 19 09:11:35 2008>>>>> >> clive@clive-desktop:~$ sudo wvdialconf wvtest>>>>> Editing `wvtest'.>>>>> >>>>>>> >> Scanning your serial ports for a modem.>>>>> >>>>>>> >> ttyS0<*1>: ATQ0 V1 E1 -- ATQ0 V1 E1>>>>> >> ttyS0<*1>: failed with 2400 baud, next try:>>>>> 9600 baud>>>>> >> ttyS0<*1>: ATQ0 V1 E1 -- OK>>>>> >> ttyS0<*1>: ATQ0 V1 E1 Z -- OK>>>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 -- OK>>>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK>>>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> -- OK>>>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0 -- OK>>>>> >> ttyS0<*1>: Modem Identifier: ATI -- IP568>>>>> Data/Fax/Voice 56K Modem>>>>> >> ttyS0<*1>: Speed 19200: AT -- OK>>>>> >> ttyS0<*1>: Speed 38400: AT -- OK>>>>> >> ttyS0<*1>: Speed 57600: AT -- OK>>>>> >> ttyS0<*1>: Speed 115200: AT -- OK>>>>> >> ttyS0<*1>: Max speed is 115200; that should>>>>> be safe.>>>>> >> ttyS0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2>>>>> +FCLASS=0 -- OK>>>>> >> Modem Port Scan<*1>: S2 S3>>>>> >>>>>>> >> Found a modem on /dev/ttyS0.>>>>> >> wvtest<Warn>: Can't open>>>>> 'wvtest' for reading: No such file or>>>>> >> directory>>>>> >> wvtest<Warn>: ...starting with blank>>>>> configuration.>>>>> >> Modem configuration written to wvtest.>>>>> >> ttyS0<Info>: Speed 115200; init "ATQ0>>>>> V1 E1 S0=0 &C1 &D2 +FCLASS=0">>>>> >> clive@clive-desktop:~$>>>>> >>>>>>> >>>>>>> >>>>>>> >>>>>> >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
