Ivan For your Linux version 2.6.15-23-386 (buildd@rothera) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Tue May 23 13:49:40 UTC 2006 scanModem update of: 2008_11_01 For candidate card in slot 0000:02:0a.0, firmware information and bootup diagnostics are: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 0000:02:0a.0 11c1:048c 11c1:044c Communication controller: Agere Systems V.92 56K WinModem This wvdialconf failure ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up means the agrsm package will not serve you, though all you have done is technically OK. Please delete the drivers and try the alternate package named suse-10-2a.tar.gz at http://phep2.technion.ac.il/linmodems/packages/ltmodem/sv92/ Compile and test as previously. This package supports more hardware, though it doen't compile under newer kernels MarvS On Jan 20, 2008 6:14 PM, - Drafter - <it.drafter@xxxxxxxxx> wrote: > OK, here it is: > > ----------------------------------------------------------------------------------------------- > brzi@brzi-linux:~$ sudo modprobe agrmodem > brzi@brzi-linux:~$ sudo modprobe agrserial > brzi@brzi-linux:~$ dmesg | grep agr > [4294936.565000] agrmodem: module license 'Proprietary' taints kernel. > brzi@brzi-linux:~$ dmesg | grep 02:0a.0 > brzi@brzi-linux:~$ sudo tail -f /var/log/messages > Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address > "xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only > configuration source at position 0 > Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address > "xml:readwrite:/root/.gconf" to a writable configuration source at > position 1 > Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address > "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only > configuration source at position 2 > Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address > "xml:readonly:/var/lib/gconf/debian.defaults" to a read-only > configuration source at position 3 > Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address > "xml:readonly:/var/lib/gconf/defaults" to a read-only configuration > source at position 4 > Jan 20 23:47:07 localhost gconfd (root-5195): GConf server is not in > use, shutting down. > Jan 20 23:47:07 localhost gconfd (root-5195): Exiting > Jan 20 23:47:53 localhost kernel: [4294936.565000] agrmodem: module > license 'Proprietary' taints kernel. > Jan 20 23:48:05 localhost kernel: [4294947.997000] ttyAGS3 at I/O > 0xb800 (irq = 10) is a AgereModem > Jan 20 23:48:05 localhost kernel: [4294947.997000] Loading module > Agere Modem Interface driver version 2.1.60.0.Linspire (2005-11-16) > ----------------------------------------------------------------------------------------------- > brzi@brzi-linux:~$ sudo ln -s /dev/ttyAGS3 /dev/ttySAGR > brzi@brzi-linux:~$ sudo wvdialconf /etc/wvdial.conf > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > Modem Port Scan<*1>: S1 S2 S3 S4 S5 S6 S7 S8 > Modem Port Scan<*1>: S9 S10 S11 S12 S13 S14 S15 S16 > Modem Port Scan<*1>: S17 S18 S19 S20 S21 S22 S23 S24 > Modem Port Scan<*1>: S25 S26 S27 S28 S29 S30 S31 S32 > Modem Port Scan<*1>: S33 S34 S35 S36 S37 S38 S39 S40 > Modem Port Scan<*1>: S41 S42 S43 S44 S45 S46 S47 > ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud > ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > > > Sorry, no modem was detected! Is it in use by another program? > Did you configure it properly with setserial? > > Please read the FAQ at http://open.nit.ca/wiki/?WvDial > > If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>. > ----------------------------------------------------------------------------------------------- > > Ivan > > > > -- > U can visit my web site @: > www.drafter.co.nr >
