OK, here it is: ----------------------------------------------------------------------------------------------- brzi@brzi-linux:~$ sudo modprobe agrmodem brzi@brzi-linux:~$ sudo modprobe agrserial brzi@brzi-linux:~$ dmesg | grep agr [4294936.565000] agrmodem: module license 'Proprietary' taints kernel. brzi@brzi-linux:~$ dmesg | grep 02:0a.0 brzi@brzi-linux:~$ sudo tail -f /var/log/messages Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address "xml:readonly:/etc/gconf/gconf.xml.mandatory" to a read-only configuration source at position 0 Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address "xml:readwrite:/root/.gconf" to a writable configuration source at position 1 Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only configuration source at position 2 Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address "xml:readonly:/var/lib/gconf/debian.defaults" to a read-only configuration source at position 3 Jan 20 23:46:37 localhost gconfd (root-5195): Resolved address "xml:readonly:/var/lib/gconf/defaults" to a read-only configuration source at position 4 Jan 20 23:47:07 localhost gconfd (root-5195): GConf server is not in use, shutting down. Jan 20 23:47:07 localhost gconfd (root-5195): Exiting Jan 20 23:47:53 localhost kernel: [4294936.565000] agrmodem: module license 'Proprietary' taints kernel. Jan 20 23:48:05 localhost kernel: [4294947.997000] ttyAGS3 at I/O 0xb800 (irq = 10) is a AgereModem Jan 20 23:48:05 localhost kernel: [4294947.997000] Loading module Agere Modem Interface driver version 2.1.60.0.Linspire (2005-11-16) ----------------------------------------------------------------------------------------------- brzi@brzi-linux:~$ sudo ln -s /dev/ttyAGS3 /dev/ttySAGR brzi@brzi-linux:~$ sudo wvdialconf /etc/wvdial.conf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Modem Port Scan<*1>: S1 S2 S3 S4 S5 S6 S7 S8 Modem Port Scan<*1>: S9 S10 S11 S12 S13 S14 S15 S16 Modem Port Scan<*1>: S17 S18 S19 S20 S21 S22 S23 S24 Modem Port Scan<*1>: S25 S26 S27 S28 S29 S30 S31 S32 Modem Port Scan<*1>: S33 S34 S35 S36 S37 S38 S39 S40 Modem Port Scan<*1>: S41 S42 S43 S44 S45 S46 S47 ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>. ----------------------------------------------------------------------------------------------- Ivan -- U can visit my web site @: www.drafter.co.nr
