Marvin, The command gives no output. Perhaps this command will help to identify the chipset: # grep -rs 11c /proc/asound/* /proc/asound/card0/codec#1:Codec: Generic 11c1 Si3054 /proc/asound/card0/codec#1:Vendor Id: 0x11c13055 /proc/asound/card0/codec#1:Subsystem Id: 0x11c11601 /proc/asound/Intel/codec#1:Codec: Generic 11c1 Si3054 /proc/asound/Intel/codec#1:Vendor Id: 0x11c13055 /proc/asound/Intel/codec#1:Subsystem Id: 0x11c11601 On Mon January 14 2008 02:42:08 Marvin Stodolsky wrote: > Alexey & Mario > > Please do > $ grep -rs 11c11040 /proc/asound/* > to check if your modem has this NOT supported chipset > > MarvS > > On 1/13/08, Alexey Pechenkin <apech@xxxxxxx> wrote: > > Hello Jacques, > > > > I repeated the test with wvdial as you requested but the outcome is > > virtually identical, NO CARRIER after slmodem saying something like: > > > > V8AGC, overflow = 0xfffffde2, > > V8: Time Out Waiting For ANSam... > > > > I tried with Stupid Mode set to 1 and 0, both to the same effect. > > I hope the new log helps ... > > > > ===================================================================== > > > > # wvdial > > --> WvDial: Internet dialer version 1.56 (abuild@balli) > > --> Cannot get information for serial port. > > --> Initializing modem. > > --> Sending: ATZ > > ATZ > > OK > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > OK > > --> Modem initialized. > > --> Idle Seconds = 300, disabling automatic reconnect. > > --> Sending: ATDT9008080 > > --> Waiting for carrier. > > ATDT9008080 > > NO CARRIER > > --> No Carrier! Trying again. > > --> Sending: ATDT9008080 > > --> Waiting for carrier. > > ATDT9008080 > > Caught signal 2: Attempting to exit gracefully... > > --> Disconnecting at Sun Jan 13 18:34:42 2008 > > ============================================================== > > # cat /etc/wvdial.conf > > > > [Dialer Defaults] > > Init1 = ATZ > > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > Modem = /dev/ttySL0 > > Phone = 9008080 > > Idle Seconds = 300 > > Password = 1111 > > Modem Type = Analog Modem > > Stupid Mode = 1 > > Compuserve = 0 > > Baud = 460800 > > Auto DNS = 1 > > Dial Command = ATDT > > Ask Password = 0 > > ISDN = 0 > > Username = 1111 > > Carrier Check = no > > > > > > ============================================================== > > slmodemd -a hw:0,6 -d 9 -c LATVIA > > SmartLink Soft Modem: version 2.9.11 Jan 5 2008 22:13:27 > > <591.920858> SmartLink Soft Modem: version 2.9.11 Jan 5 2008 22:13:27 > > <591.920904> hw:0,6: startup modem... > > <591.921009> hw:0,6: update termios... > > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > > modem `hw:0,6' created. TTY is `/dev/pts/2' > > <591.921253> open file: /var/lib/slmodem/data.hw:0,6... > > <591.922931> main: rt applyed: SCHED_FIFO, pri 99 > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > <597.344905> main: termios changed. > > <597.344926> hw:0,6: update termios... > > <597.422755> main: termios changed. > > <597.422778> hw:0,6: update termios... > > <597.522676> hw:0,6: run cmd: ATZ > > <597.522701> hw:0,6: modem reset... > > <597.522707> hw:0,6: modem set state: 1 --> 1... > > <597.522714> hw:0,6: modem set mode: -> 0... > > <597.522718> hw:0,6: modem report result: 0 (OK) > > <597.622860> hw:0,6: run cmd: ATQ0V1E1S0=0&C1&D2+FCLASS=0 > > <597.622893> hw:0,6: modem set mode: -> 0... > > <597.622903> hw:0,6: modem report result: 0 (OK) > > <597.722811> hw:0,6: run cmd: ATDT9008080 > > <597.722837> hw:0,6: modem dial: T9008080... > > <597.722842> hw:0,6: modem_dial_start... > > <597.722847> call: create... > > <597.722856> CallProgFP_Create >> > > <597.722860> APPLY_FILTER = 0 > > <597.722866> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90 > > <597.722872> ============> 0 > > <597.722876> Cadence: Busy Tone loose detection is 0 > > <597.722882> TYPE BUSY > > <597.722886> Filter index 0 > > <597.722889> Filter SubIndex 0 > > <597.722893> MAX_ON_TIME 27 Buffers MIN_ON_TIME 10 Buffers > > <597.722898> MAX_OFF_TIME 27 Buffers MIN_OFF_TIME 10 Buffers > > <597.722902> OFF_TIME_THAT_RESETS_CYCLE 81 > > <597.722906> BUFFER LENGTH 160 samples. > > <597.722910> INTEGRATION_LENGTH 0[ms] > > <597.722914> LEVEL 90 > > <597.722921> INTEGRATION_TIME = 0 Buffers. > > <597.722926> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90 > > <597.722931> TYPE DIAL > > <597.722935> Filter index 3 > > <597.722938> Filter SubIndex 0 > > <597.722942> MAX_ON_TIME 0 Buffers MIN_ON_TIME 0 Buffers > > <597.722946> MAX_OFF_TIME 0 Buffers MIN_OFF_TIME 0 Buffers > > <597.722950> OFF_TIME_THAT_RESETS_CYCLE 0 > > <597.722954> BUFFER LENGTH 666 samples. > > <597.722958> INTEGRATION_LENGTH 200[ms] > > <597.722962> LEVEL 90 > > <597.722966> INTEGRATION_TIME = 1 Buffers. > > <597.722972> CALLPROG Create << > > <597.722976> CALLPROG Dialing T9008080 > > <597.722981> Configuration->tone_DigitLength 100 > > <597.722985> Configuration->pulse_OffHookTime 40 > > <597.722989> Configuration->pulse_OnHookTime 60 > > <597.722992> Configuration->dialPauseTime 4 > > <597.722996> Configuration->flashTime 7 > > <597.723000> Configuration->toneOrPulseFlag 0 > > <597.723004> Configuration->dialModifierValidationFlag 0 > > <597.723008> Configuration->ABCD_PermittedFlag 0 > > <597.723012> Configuration->pulseAndToneInSameStringPermittedFlag 0 > > <597.723017> Configuration->callingToneFlag 0 > > <597.723020> Configuration->commaPauseDurLimit 30 > > <597.723025> Configuration->digitPattern 1 > > <597.723028> Configuration->tone_BetweenDigitsInterval 100 > > <597.723032> Configuration->pulse_BetweenDigitsInterval 800 > > <597.723037> DTMF_Gain1 = 10337 > > <597.723041> DTMF_Gain2 = 13014 > > <597.723045> AnalyzeDialString: Updated 17 May 1999 00:50 > > <597.723050> AnalyzeDialString: LAST_DIALABLE_SYMBOL is 7 > > <597.723054> Dial String Syntax is VALID > > <597.723060> GetNoAnswerTimeOut. 60 > > <597.723064> WAIT DIAL TIMEOUT = 4 > > <597.723068> CALLPROG_Dial was exited. > > <597.723072> call: create RC: 9600 <-> 8000... > > <597.723079> hw:0,6: modem_start.. > > <597.723084> hw:0,6: modem set state: 1 --> 2... > > <597.723090> hw:0,6: new state: DP_ESTAB > > <597.723094> main: alsa_ioctl: cmd 8, arg 3... > > <597.723098> hw:0,6: modem set hook: 0 --> 1... > > <597.723102> main: alsa_ioctl: cmd 2, arg 1... > > <597.723253> main: alsa_ioctl: cmd 11, arg 0... > > <597.723320> main: alsa_ioctl: cmd 4, arg 2580... > > <597.723324> main: alsa_ioctl: cmd 7, arg 30... > > <597.723328> main: alsa_start... > > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0 > > Its setup is: > > stream : PLAYBACK > > access : RW_INTERLEAVED > > format : S16_LE > > subformat : STD > > channels : 1 > > rate : 9600 > > exact rate : 9600 (9600/1) > > msbits : 16 > > buffer_size : 2048 > > period_size : 64 > > period_time : 6666 > > tick_time : 4000 > > tstamp_mode : NONE > > period_step : 1 > > sleep_min : 0 > > avail_min : 4 > > xfer_align : 4 > > start_threshold : 2147483647 > > stop_threshold : 2048 > > silence_threshold: 0 > > silence_size : 0 > > boundary : 1073741824 > > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0 > > Its setup is: > > stream : CAPTURE > > access : RW_INTERLEAVED > > format : S16_LE > > subformat : STD > > channels : 1 > > rate : 9600 > > exact rate : 9600 (9600/1) > > msbits : 16 > > buffer_size : 2048 > > period_size : 64 > > period_time : 6666 > > tick_time : 4000 > > tstamp_mode : NONE > > period_step : 1 > > sleep_min : 0 > > avail_min : 4 > > xfer_align : 4 > > start_threshold : 2147483647 > > stop_threshold : 2048 > > silence_threshold: 0 > > silence_size : 0 > > boundary : 1073741824 > > <597.754820> main: startup write: 384... > > <597.761596> call: process: msg 18 --> 0 > > <598.341572> tone detected by cadence dial > > <598.341594> STATE: CALLPROG_WAIT_DIAL --> CALLPROG_DIALING > > <598.341619> call: process: msg 0 --> 3 > > <598.348243> DIALER_INITIAL_STATE > > <598.348257> Digit is T > > <598.348264> Dialer.c: GetNextDigit... TONE_OR_PULSE_FLAG became > > TONE_DIALING <598.348271> Digit is 9 > > <598.348278> Samples left = 800 > > <598.348300> call: process: msg 3 --> 0 > > <598.428228> tone detected by cadence dial > > <598.441580> Done Generating digit > > <598.508240> tone detected by cadence dial > > <598.541597> Done Generating silence between digits > > <598.541631> Digit is 0 > > <598.541640> Samples left = 800 > > <598.574973> CYCLES_COUNTER= 1 > > <598.594911> CYCLES_COUNTER= 1 > > <598.641565> Done Generating digit > > <598.741588> Done Generating silence between digits > > <598.741615> Digit is 0 > > <598.741623> Samples left = 800 > > <598.841607> Done Generating digit > > <598.941594> Done Generating silence between digits > > <598.941622> Digit is 8 > > <598.941630> Samples left = 800 > > <599.041584> Done Generating digit > > <599.141588> Done Generating silence between digits > > <599.141615> Digit is 0 > > <599.141622> Samples left = 800 > > <599.241572> Done Generating digit > > <599.341588> Done Generating silence between digits > > <599.341615> Digit is 8 > > <599.341624> Samples left = 800 > > <599.354904> DCR: initial DC Evaluation done, DC level -207, enabled > > <599.441576> Done Generating digit > > <599.541592> Done Generating silence between digits > > <599.541619> Digit is 0 > > <599.541627> Samples left = 800 > > <599.641595> Done Generating digit > > <599.648261> DIALER_END_STATE > > <599.648274> STATE: CALLPROG_DIALING --> CALLPROG_WAIT_RING > > <599.648293> call: process: msg 0 --> 4 > > <599.654935> call: process: msg 4 --> 0 > > <603.275032> CYCLES_COUNTER= 2 > > <610.721760> Found 2250 > > <610.721796> call: process: msg 0 --> 17 > > <610.721805> hw:0,6: 124416: change dp: --> 8... > > <610.721815> v8: create: caller 1, automode 0, dp id 92. > > <610.721827> V8: Create called, V8 version 23/09/03 . > > <610.721833> ############################################################ > > <610.721841> V8: local configuration : > > <610.721847> Side = Caller > > <610.721855> Operation Mode = 0 > > <610.721863> Modulations - V90=1, V34=1, V34HD=0, V32=1, V22=0, V17=0, > > V29=0, V27=0, V23=0, V21=0 > > <610.721874> Call Functions - Data=1, CallRxFax=0, CallTxFax=0, V.80=0 > > <610.721884> Protocol - LAPM V.42 > > <610.721891> v8bisIndication - 0 > > <610.721899> timeouts - signal detect 12 sec, message detect 7 sec > > <610.721908> quickConnectEnabled - 1 > > <610.721915> lapmIndication - 1 > > <610.721923> ucodeForQts - 9 > > <610.721930> ansPcmLevel - 0 > > <610.721937> ############################################################ > > <610.721950> V8: Initial CM message length is 9 octets > > <610.721959> call: delete... > > <610.721965> Dialer was aborted. > > <610.721972> CALLPROG_Delete is entered > > <610.721978> cadence_delete with CADENCE_DIAL_OBJ is invoked > > <610.721986> cadence_delete with CADENCE_OBJ is invoked > > <610.721994> CALLPROG_Delete is exited > > <610.722014> V8: State changed from V8_INIT to V8_ORG_WAITING_FOR_ANSAM > > <610.722022> v8: status (6) V8_ORG_WAITING_FOR_ANSAM > > <618.428577> V8AGC, overflow = 0x216, > > <621.135240> V8AGC, overflow = 0x265, > > <621.135266> V8AGC, overflow = 0xfffffda2, > > <622.488593> V8AGC, overflow = 0xfffffde2, > > <622.721969> V8: Time Out Waiting For ANSam... > > <622.721997> V8: State changed from V8_ORG_WAITING_FOR_ANSAM to > > V8_ORG_TIME_OUT_WAITING_FOR_ANSAM > > <622.722009> v8: process: timeout. > > <622.722015> v8: status (11) V8_ORG_TIME_OUT_WAITING_FOR_ANSAM > > <622.722022> hw:0,6: modem_update_status: 512 > > <622.722029> hw:0,6: --> FINISH. > > <622.722035> hw:0,6: modem_hup... > > <622.722041> hw:0,6: modem set state: 2 --> 9... > > <622.722053> hw:0,6: new state: DP_DISC > > <622.722060> hw:0,6: modem_stop.. > > <622.722066> main: alsa_stop... > > <622.740195> hw:0,6: modem set hook: 1 --> 0... > > <622.740221> main: alsa_ioctl: cmd 2, arg 0... > > <622.740369> main: alsa_ioctl: cmd 8, arg 0... > > <622.740381> v8: delete... > > <622.740390> hw:0,6: modem set state: 9 --> 1... > > <622.740411> hw:0,6: new state: MODEM_IDLE > > <622.740418> hw:0,6: modem report result: 3 (NO CARRIER) > > <622.740437> main: dev write = 0 > > <623.040431> hw:0,6: run cmd: ATDT9008080 > > <623.040457> hw:0,6: modem dial: T9008080... > > <623.040464> hw:0,6: modem_dial_start... > > <623.040472> call: create... > > <623.040483> CallProgFP_Create >> > > <623.040490> APPLY_FILTER = 0 > > <623.040499> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90 > > <623.040508> ============> 0 > > <623.040514> Cadence: Busy Tone loose detection is 0 > > <623.040524> TYPE BUSY > > <623.040530> Filter index 0 > > <623.040536> Filter SubIndex 0 > > <623.040543> MAX_ON_TIME 27 Buffers MIN_ON_TIME 10 Buffers > > <623.040550> MAX_OFF_TIME 27 Buffers MIN_OFF_TIME 10 Buffers > > <623.040558> OFF_TIME_THAT_RESETS_CYCLE 81 > > <623.040564> BUFFER LENGTH 160 samples. > > <623.040571> INTEGRATION_LENGTH 0[ms] > > <623.040578> LEVEL 90 > > <623.040588> INTEGRATION_TIME = 0 Buffers. > > <623.040597> Detection Thresholds: levle_fix=45,--> LEVEL_THRESHOLD=90 > > <623.040605> TYPE DIAL > > <623.040612> Filter index 3 > > <623.040618> Filter SubIndex 0 > > <623.040624> MAX_ON_TIME 0 Buffers MIN_ON_TIME 0 Buffers > > <623.040631> MAX_OFF_TIME 0 Buffers MIN_OFF_TIME 0 Buffers > > <623.040639> OFF_TIME_THAT_RESETS_CYCLE 0 > > <623.040645> BUFFER LENGTH 666 samples. > > <623.040652> INTEGRATION_LENGTH 200[ms] > > <623.040659> LEVEL 90 > > <623.040666> INTEGRATION_TIME = 1 Buffers. > > <623.040675> CALLPROG Create << > > <623.040682> CALLPROG Dialing T9008080 > > <623.040689> Configuration->tone_DigitLength 100 > > <623.040696> Configuration->pulse_OffHookTime 40 > > <623.040703> Configuration->pulse_OnHookTime 60 > > <623.040710> Configuration->dialPauseTime 4 > > <623.040717> Configuration->flashTime 7 > > <623.040724> Configuration->toneOrPulseFlag 0 > > <623.040730> Configuration->dialModifierValidationFlag 0 > > <623.040737> Configuration->ABCD_PermittedFlag 0 > > <623.040744> Configuration->pulseAndToneInSameStringPermittedFlag 0 > > <623.040751> Configuration->callingToneFlag 0 > > <623.040758> Configuration->commaPauseDurLimit 30 > > <623.040765> Configuration->digitPattern 1 > > <623.040771> Configuration->tone_BetweenDigitsInterval 100 > > <623.040778> Configuration->pulse_BetweenDigitsInterval 800 > > <623.040786> DTMF_Gain1 = 10337 > > <623.040792> DTMF_Gain2 = 13014 > > <623.040800> AnalyzeDialString: Updated 17 May 1999 00:50 > > <623.040807> AnalyzeDialString: LAST_DIALABLE_SYMBOL is 7 > > <623.040814> Dial String Syntax is VALID > > <623.040821> GetNoAnswerTimeOut. 60 > > <623.040828> WAIT DIAL TIMEOUT = 4 > > <623.040835> CALLPROG_Dial was exited. > > <623.040841> call: create RC: 9600 <-> 8000... > > <623.040851> hw:0,6: modem_start.. > > <623.040858> hw:0,6: modem set state: 1 --> 2... > > <623.040867> hw:0,6: new state: DP_ESTAB > > <623.040874> main: alsa_ioctl: cmd 8, arg 3... > > <623.040882> hw:0,6: modem set hook: 0 --> 1... > > <623.040889> main: alsa_ioctl: cmd 2, arg 1... > > <623.041021> main: alsa_ioctl: cmd 11, arg 0... > > <623.041116> main: alsa_ioctl: cmd 4, arg 2580... > > <623.041125> main: alsa_ioctl: cmd 7, arg 30... > > <623.041132> main: alsa_start... > > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0 > > Its setup is: > > stream : PLAYBACK > > access : RW_INTERLEAVED > > format : S16_LE > > subformat : STD > > channels : 1 > > rate : 9600 > > exact rate : 9600 (9600/1) > > msbits : 16 > > buffer_size : 2048 > > period_size : 64 > > period_time : 6666 > > tick_time : 4000 > > tstamp_mode : NONE > > period_step : 1 > > sleep_min : 0 > > avail_min : 4 > > xfer_align : 4 > > start_threshold : 2147483647 > > stop_threshold : 2048 > > silence_threshold: 0 > > silence_size : 0 > > boundary : 1073741824 > > Hardware PCM card 0 'HDA Intel' device 6 subdevice 0 > > Its setup is: > > stream : CAPTURE > > access : RW_INTERLEAVED > > format : S16_LE > > subformat : STD > > channels : 1 > > rate : 9600 > > exact rate : 9600 (9600/1) > > msbits : 16 > > buffer_size : 2048 > > period_size : 64 > > period_time : 6666 > > tick_time : 4000 > > tstamp_mode : NONE > > period_step : 1 > > sleep_min : 0 > > avail_min : 4 > > xfer_align : 4 > > start_threshold : 2147483647 > > stop_threshold : 2048 > > silence_threshold: 0 > > silence_size : 0 > > boundary : 1073741824 > > <623.076452> main: startup write: 384... > > <623.083180> call: process: msg 18 --> 0 > > <623.663145> tone detected by cadence dial > > <623.663169> STATE: CALLPROG_WAIT_DIAL --> CALLPROG_DIALING > > <623.663195> call: process: msg 0 --> 3 > > <623.669820> DIALER_INITIAL_STATE > > <623.669832> Digit is T > > <623.669839> Dialer.c: GetNextDigit... TONE_OR_PULSE_FLAG became > > TONE_DIALING <623.669847> Digit is 9 > > <623.669854> Samples left = 800 > > <623.669875> call: process: msg 3 --> 0 > > <623.749806> tone detected by cadence dial > > <623.763173> Done Generating digit > > <623.829822> tone detected by cadence dial > > <623.863161> Done Generating silence between digits > > <623.863184> Digit is 0 > > <623.863189> Samples left = 800 > > <623.896502> CYCLES_COUNTER= 1 > > <623.916488> CYCLES_COUNTER= 1 > > <623.963142> Done Generating digit > > <624.063147> Done Generating silence between digits > > <624.063172> Digit is 0 > > <624.063179> Samples left = 800 > > <624.163155> Done Generating digit > > <624.263176> Done Generating silence between digits > > <624.263205> Digit is 8 > > <624.263214> Samples left = 800 > > <624.363156> Done Generating digit > > <624.463162> Done Generating silence between digits > > <624.463189> Digit is 0 > > <624.463197> Samples left = 800 > > <624.563170> Done Generating digit > > <624.663168> Done Generating silence between digits > > <624.663197> Digit is 8 > > <624.663206> Samples left = 800 > > <624.676475> DCR: initial DC Evaluation done, DC level -216, enabled > > <624.763153> Done Generating digit > > <624.863161> Done Generating silence between digits > > <624.863183> Digit is 0 > > <624.863188> Samples left = 800 > > <624.963162> Done Generating digit > > <624.969841> DIALER_END_STATE > > <624.969859> STATE: CALLPROG_DIALING --> CALLPROG_WAIT_RING > > <624.969874> call: process: msg 0 --> 4 > > <624.976504> call: process: msg 4 --> 0 > > <635.969235> hw:0,6: modem_tty_write: hangup... > > <635.969254> hw:0,6: modem_hup... > > <635.969265> hw:0,6: modem set state: 2 --> 9... > > <635.969274> hw:0,6: new state: DP_DISC > > <635.969287> main: termios changed. > > <635.969294> hw:0,6: update termios... > > <635.969308> main: pty closed. > > <635.970013> hw:0,6: modem_stop.. > > <635.970023> main: alsa_stop... > > <635.985017> hw:0,6: modem set hook: 1 --> 0... > > <635.985043> main: alsa_ioctl: cmd 2, arg 0... > > <635.985199> main: alsa_ioctl: cmd 8, arg 0... > > <635.985210> call: delete... > > <635.985217> Dialer was aborted. > > <635.985222> CALLPROG_Delete is entered > > <635.985241> cadence_delete with CADENCE_DIAL_OBJ is invoked > > <635.985249> cadence_delete with CADENCE_OBJ is invoked > > <635.985255> CALLPROG_Delete is exited > > <635.985264> hw:0,6: modem set state: 9 --> 1... > > <635.985271> hw:0,6: new state: MODEM_IDLE > > <635.985277> hw:0,6: modem report result: 3 (NO CARRIER) > > <635.985292> main: dev write = 0 > > <638.687422> main: signal 2: mark termination. > > <638.687499> hw:0,6: modem_delete... > > > > On Sun January 13 2008 14:34:39 Jacques Goldberg wrote: > > > Alexey, > > > The tool which you have used to try to dial does not show relevant > > > information, at least at my level of understanding. > > > > > > Give the following command > > > slmodemd -a hw:0,6 -d 9 -c LATVIA > > > and DO NOT STOP IT. > > > In an other window, as root (su) give the command > > > wvdialconf /etc/wvdial.conf > > > If this detects the modem, it will work: then, edit the file > > > /etc/wvdial.conf > > > Three things are obvious: phone number, username, password. > > > For these three lines remove ; > and < and replace the word which was > > > in < ... > by its value given by your ISP > > > Last thing, add one line: > > > Carrier Check = no > > > Save and exit the editor. > > > > > > Next, just type > > > wvdial > > > and you should be connected. > > > wvdial and slmodemd are stopped by typing CTRL-C once you does not need > > > them anynore (close the connection) > > > > > > Jacques > > > > -- > > > > Best regards, > > > > Alexey -- -- Best regards, Alexey
