Bob, 1) ///////////////////////////// $ slmodemd -c USA /dev/slamr0 error: mdm setup: cannot open dev `/dev/slamr0': Device or resource busy error: cannot setup device `/dev/slamr0' ------------ My guess is due to the slmodemd already having been run by the bootup scripts, so that it cannot be reloaded You could however $ sudo /etc/init.d/sl-modem-daemon stop and then $ sudo slmodemd -c USA /dev/slamr0 Note that "sudo slmodemd" is essential, that is Admin/root capacity is needed. 2) from the lsmod output: slamr 433448 2 psmouse 38920 0 parport_pc 36388 1 parport 36936 3 ppdev,lp,parport_pc usblp 14848 0 serio_raw 7940 0 pcspkr 4224 0 ungrab_winmodem 3712 0 --------- ungrab_winmodem was loaded before slamr, as is necessary 3) From lspci output: 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 the modem is in PCI bus slot 02:0a.0 4) During bootup processes [ 13.195827] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 16 [ 13.195840] ACPI: PCI interrupt for device 0000:02:0a.0 disabled this slot is first disabled and then enabled later, evidently during test loading of the slamr driver: [ 33.640912] slamr: module license 'Smart Link Ltd.' taints kernel. [ 33.649995] slamr: SmartLink AMRMO modem. [ 33.651044] slamr: probe 2000:2800 SL2800 card... [ 33.651060] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 16 [ 33.652166] slamr: slamr0 is SL2800 card The IRQ 16 does not seem to be shared with other hardware. 5) From the wvdialconf success through ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem and further, the slamr driver is at least accessing the modem firmware because "SmartLink Soft Modem" is written in the firmware. 6) Your /etc/wvdial.conf is OK So it is not yet transparent why there is the later failure with: > --> Waiting for carrier. > ATDT6875000 > --> Disconnecting at Thu Nov 8 20:58:32 2007 Note that everytime you run $ sudo wvdialconf /etc/wvdial.conf the prior wvdial.conf is overwritten. So check that it is OK before your next testing. With respect to shutdown, just do $ sudo /etc/init.d/sl-modem-daemon stop Or if you started slmodemd manually, then in that console you can just: CTRL-C Then $ sudo modprobe -r slamr to unload the driver $ sudo modprobe slamr will reload, after which you could manually do: $ sudo slmodemd -c USA /dev/slamr0 and in a 2nd console: $ sudo wvdial Try and get somemore information by: $ sudo slmodemd -c USA --log --debug=1 /dev/slamr0 which will write a log file you can later send us after the dialout attempt, To compile your own software under 2.6.22-14-generic., you need to install the packages: linux-headers-2.6.22-14 and linux-headers-2.6.22-14-generic. Let us know if you have an alternate ethernet CONNECT and we will instruct. More tomorrow MarvS On 11/8/07, Bob Terrell <bob_terrell_texas@xxxxxxxxx> wrote: > Greetings, > > I am still having the problem that any dialer, > including using ONLY wvdial, will show a disconnect, > but still leaves the line and carrier active. A reboot > is required to get the system to hang up. > > Jacques was correct, I had not started slmodemd in a > separate window before starting wvdial. When I try to > start that, it states that it cannot find /dev/slamr0 > (see the output below). > Also, I could have installed the M1 L3 statement with > Gnome PPP, but I am not sure how to take it out. It > does not currently show in the Gnome PPP INIT 2 > string. > > ONE MORE QUESTION: I have setup a system for Ubuntu > 7.10 2.6.22-14-generic. It requires that I compile > slmodemd. When I run make, it gives me a lot of errors > because it cannot find the header files, like stderr.h > plus about 20 others. I seem to have all the > development libraries installed, so I'm not sure what > to do next. > > Thanks for all you do! > Bob Terrell > > ///////////////////////////// > LISTED BELOW IN ORDER: > $ sudo wvdialconf /etc/wvdial.conf > $ cat /etc/wvdial.conf > $ slmodemd -c USA /dev/slamr0 > $ dmesg | grep -i 02:0a > $ wvdial > wvdial.out2 > $ lsmod > $ lspci | grep -v bridge > $ lspci | grep -v USB > $ lspci | grep -v RAM > $ dmesg | dmesg.txt > > ///////////////////////////// > $ sudo wvdialconf /etc/wvdial.conf > Password: > Editing `/etc/wvdial.conf'. > > Scanning your serial ports for a modem. > > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next > try: 9600 baud > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next > try: 115200 baud > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, > giving up. > ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next > try: 9600 baud > ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next > try: 115200 baud > ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, > giving up. > Modem Port Scan<*1>: S2 S3 > WvModem<*1>: Cannot get information for serial port. > ttySL0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next > try: 9600 baud > ttySL0<*1>: ATQ0 V1 E1 -- OK > ttySL0<*1>: ATQ0 V1 E1 Z -- OK > ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft > Modem > ttySL0<*1>: Speed 19200: AT -- OK > ttySL0<*1>: Speed 38400: AT -- OK > ttySL0<*1>: Speed 57600: AT -- OK > ttySL0<*1>: Speed 115200: AT -- OK > ttySL0<*1>: Speed 230400: AT -- OK > ttySL0<*1>: Speed 460800: AT -- OK > ttySL0<*1>: Max speed is 460800; that should be safe. > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > > Found a modem on /dev/ttySL0. > Modem configuration written to /etc/wvdial.conf. > ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 > &D2 +FCLASS=0" > $ > > //////////////////////////// > $ cat /etc/wvdial.conf > > [Dialer Defaults] > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > Modem Type = Analog Modem > ISDN = 0 > New PPPD = yes > Phone = 6875000 > Modem = /dev/ttySL0 > Username = acooper > Carrier check = no > Password = erased > Baud = 460800 > $ > > ///////////////////////////// > $ slmodemd -c USA /dev/slamr0 > error: mdm setup: cannot open dev `/dev/slamr0': > Device or resource busy > error: cannot setup device `/dev/slamr0' > $ > > ////////////////////////////// > $ dmesg | grep -i 02:0a > [ 13.195827] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > GSI 22 (level, low) -> IRQ 16 > [ 13.195840] ACPI: PCI interrupt for device > 0000:02:0a.0 disabled > [ 33.651060] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > GSI 22 (level, low) -> IRQ 16 > $ > > /////////////////////////////// > $ wvdial > wvdial.out2 > --> WvDial: Internet dialer version 1.56 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT6875000 > --> Waiting for carrier. > ATDT6875000 > --> Disconnecting at Thu Nov 8 20:58:32 2007 > $ ls -al wv* > -rw-r--r-- 1 user1 user1 0 2007-11-08 20:58 > wvdial.out2 > NOTE: line connected with carrier still playing > $ > > ///////////////////////// > $ lsmod > Module Size Used by > rfcomm 40856 0 > l2cap 25856 5 rfcomm > bluetooth 55908 4 rfcomm,l2cap > r128 40832 2 > drm 81044 3 r128 > ppdev 10116 0 > speedstep_lib 6148 0 > cpufreq_userspace 5408 0 > cpufreq_ondemand 9228 0 > cpufreq_stats 7360 0 > freq_table 5792 2 > cpufreq_ondemand,cpufreq_stats > cpufreq_conservative 8200 0 > cpufreq_powersave 2688 0 > pcc_acpi 13184 0 > dev_acpi 12292 0 > sony_acpi 6284 0 > tc1100_wmi 8068 0 > dock 10268 0 > sbs 15652 0 > asus_acpi 17308 0 > backlight 7040 1 asus_acpi > i2c_ec 6016 1 sbs > i2c_core 22656 1 i2c_ec > battery 10756 0 > ac 6020 0 > button 8720 0 > container 5248 0 > video 16388 0 > ipv6 268960 8 > lp 12452 0 > fuse 46612 0 > snd_intel8x0 34332 1 > snd_ac97_codec 98464 1 snd_intel8x0 > ac97_bus 3200 1 snd_ac97_codec > snd_pcm_oss 44544 0 > snd_mixer_oss 17408 1 snd_pcm_oss > snd_pcm 79876 3 > snd_intel8x0,snd_ac97_codec,snd_pcm_oss > snd_seq_dummy 4740 0 > snd_seq_oss 32896 0 > snd_seq_midi 9600 0 > snd_rawmidi 25472 1 snd_seq_midi > snd_seq_midi_event 8448 2 > snd_seq_oss,snd_seq_midi > snd_seq 52592 6 > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event > snd_timer 23684 2 snd_pcm,snd_seq > snd_seq_device 9100 5 > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq > snd 54020 12 > snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > soundcore 8672 1 snd > slamr 433448 2 > psmouse 38920 0 > parport_pc 36388 1 > parport 36936 3 ppdev,lp,parport_pc > usblp 14848 0 > serio_raw 7940 0 > pcspkr 4224 0 > ungrab_winmodem 3712 0 > snd_page_alloc 10888 2 snd_intel8x0,snd_pcm > intel_agp 26140 1 > agpgart 35400 2 drm,intel_agp > iTCO_wdt 11812 0 > iTCO_vendor_support 4868 1 iTCO_wdt > shpchp 34324 0 > pci_hotplug 32576 1 shpchp > af_packet 23816 2 > evdev 11008 3 > tsdev 8768 0 > ext3 133128 1 > jbd 59816 1 ext3 > mbcache 9604 1 ext3 > sg 36252 0 > sr_mod 17060 0 > cdrom 37664 1 sr_mod > sd_mod 23428 3 > generic 5124 0 [permanent] > floppy 59524 0 > e100 36232 0 > mii 6528 1 e100 > uhci_hcd 25360 0 > usbcore 134280 3 usblp,uhci_hcd > ata_piix 15492 2 > ata_generic 9092 0 > libata 125720 2 ata_piix,ata_generic > scsi_mod 142348 4 > sg,sr_mod,sd_mod,libata > thermal 14856 0 > processor 31048 1 thermal > fan 5636 0 > fbcon 42656 0 > tileblit 3584 1 fbcon > font 9216 1 fbcon > bitblit 6912 1 fbcon > softcursor 3200 1 bitblit > vesafb 9220 0 > capability 5896 0 > commoncap 8192 1 capability > $ > > //////////////////////////////////// > $ lspci | grep -v bridge > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > U100 (rev 05) > 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #1) (rev 05) > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > (rev 05) > 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #2) (rev 05) > 00:1f.5 Multimedia audio controller: Intel Corporation > 82801BA/BAM AC'97 Audio (rev 05) > 01:00.0 VGA compatible controller: ATI Technologies > Inc Rage 128 PF/PRO AGP 4x TMDS > $ > > ////////////////////////////////////////// > $ lspci | grep -v bridge > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > U100 (rev 05) > 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #1) (rev 05) > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > (rev 05) > 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #2) (rev 05) > 00:1f.5 Multimedia audio controller: Intel Corporation > 82801BA/BAM AC'97 Audio (rev 05) > 01:00.0 VGA compatible controller: ATI Technologies > Inc Rage 128 PF/PRO AGP 4x TMDS > user1@user1-desktop:~/DownloadFolder/Modem$ lspci | > grep -v USB00:00.0 Host bridge: Intel Corporation > 82845 845 (Brookdale) Chipset Host Bridge (rev 04) > 00:01.0 PCI bridge: Intel Corporation 82845 845 > (Brookdale) Chipset AGP Bridge (rev 04)Down00:1e.0 PCI > bridge: Intel Corporation 82801 PCI Bridge (rev > 05)00:1f.0 ISA bridge: Intel Corporation 82801BA ISA > Bridge (LPC) (rev 05) > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > U100 (rev 05) > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > (rev 05) > 00:1f.5 Multimedia audio controller: Intel Corporation > 82801BA/BAM AC'97 Audio (rev 05) > 01:00.0 VGA compatible controller: ATI Technologies > Inc Rage 128 PF/PRO AGP 4x TMDS > 02:08.0 Ethernet controller: Intel Corporation > 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) > 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 > (rev 02) > $ > > /////////////////////////////////////////// > $ lspci | grep -v RAM > 00:00.0 Host bridge: Intel Corporation 82845 845 > (Brookdale) Chipset Host Bridge (rev 04) > 00:01.0 PCI bridge: Intel Corporation 82845 845 > (Brookdale) Chipset AGP Bridge (rev 04) > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge > (rev 05) > 00:1f.0 ISA bridge: Intel Corporation 82801BA ISA > Bridge (LPC) (rev 05) > 00:1f.1 IDE interface: Intel Corporation 82801BA IDE > U100 (rev 05) > 00:1f.2 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #1) (rev 05) > 00:1f.3 SMBus: Intel Corporation 82801BA/BAM SMBus > (rev 05) > 00:1f.4 USB Controller: Intel Corporation 82801BA/BAM > USB (Hub #2) (rev 05) > 00:1f.5 Multimedia audio controller: Intel Corporation > 82801BA/BAM AC'97 Audio (rev 05) > 01:00.0 VGA compatible controller: ATI Technologies > Inc Rage 128 PF/PRO AGP 4x TMDS > 02:08.0 Ethernet controller: Intel Corporation > 82801BA/BAM/CA/CAM Ethernet Controller (rev 03) > 02:0a.0 Modem: Smart Link Ltd. Unknown device 2800 > (rev 02) > $ > > ///////////////////////////// > $ dmesg > dmesg.txt > [ 0.000000] Linux version 2.6.20-16-generic > (root@terranova) (gcc version 4.1.2 (Ubuntu > 4.1.2-0ubuntu4)) #2 SMP Sun Sep 23 19:50:39 UTC 2007 > (Ubuntu 2.6.20-16.32-generic) > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] sanitize start > [ 0.000000] sanitize end > [ 0.000000] copy_e820_map() start: 0000000000000000 > size: 000000000009fc00 end: 000000000009fc00 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000000009fc00 > size: 0000000000000400 end: 00000000000a0000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000000e0000 > size: 0000000000020000 end: 0000000000100000 type: 2 > [ 0.000000] copy_e820_map() start: 0000000000100000 > size: 000000000fec0000 end: 000000000ffc0000 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000000ffc0000 > size: 0000000000038000 end: 000000000fff8000 type: 3 > [ 0.000000] copy_e820_map() start: 000000000fff8000 > size: 0000000000008000 end: 0000000010000000 type: 4 > [ 0.000000] copy_e820_map() start: 00000000fec00000 > size: 0000000000001000 end: 00000000fec01000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000fee00000 > size: 0000000000001000 end: 00000000fee01000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000ffb80000 > size: 0000000000080000 end: 00000000ffc00000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000fff00000 > size: 0000000000100000 end: 0000000100000000 type: 2 > [ 0.000000] BIOS-e820: 0000000000000000 - > 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - > 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000e0000 - > 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - > 000000000ffc0000 (usable) > [ 0.000000] BIOS-e820: 000000000ffc0000 - > 000000000fff8000 (ACPI data) > [ 0.000000] BIOS-e820: 000000000fff8000 - > 0000000010000000 (ACPI NVS) > [ 0.000000] BIOS-e820: 00000000fec00000 - > 00000000fec01000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - > 00000000fee01000 (reserved) > [ 0.000000] BIOS-e820: 00000000ffb80000 - > 00000000ffc00000 (reserved) > [ 0.000000] BIOS-e820: 00000000fff00000 - > 0000000100000000 (reserved) > [ 0.000000] 0MB HIGHMEM available. > [ 0.000000] 255MB LOWMEM available. > [ 0.000000] Entering add_active_range(0, 0, 65472) > 0 entries of 256 used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 65472 > [ 0.000000] HighMem 65472 -> 65472 > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 65472 > [ 0.000000] On node 0 totalpages: 65472 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 479 pages used for > memmap > [ 0.000000] Normal zone: 60897 pages, LIFO > batch:15 > [ 0.000000] HighMem zone: 0 pages used for memmap > [ 0.000000] DMI 2.3 present. > [ 0.000000] ACPI: RSDP (v000 AMI > ) @ 0x000ff980 > [ 0.000000] ACPI: RSDT (v001 D845PT BG84510A > 0x20020419 MSFT 0x00001011) @ 0x0fff0000 > [ 0.000000] ACPI: FADT (v001 D845PT PT84510A > 0x20020419 MSFT 0x00001011) @ 0x0fff1000 > [ 0.000000] ACPI: MADT (v001 D845PT PT84510A > 0x20020419 MSFT 0x00001011) @ 0x0ffe36fd > [ 0.000000] ACPI: DSDT (v001 D845PT PT84510A > 0x00000003 MSFT 0x0100000b) @ 0x00000000 > [ 0.000000] ACPI: PM-Timer IO Port: 0x408 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x01] > lapic_id[0x00] enabled) > [ 0.000000] Processor #0 15:2 APIC version 20 > [ 0.000000] ACPI: LAPIC (acpi_id[0x02] > lapic_id[0x01] disabled) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl > lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl > lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x02] > address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 32, > address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 > global_irq 9 high level) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 > global_irq 2 dfl dfl) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] ACPI: IRQ9 used by override. > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O > APICs > [ 0.000000] Using ACPI (MADT) for SMP configuration > information > [ 0.000000] Allocating PCI resources starting at > 20000000 (gap: 10000000:eec00000) > [ 0.000000] Detected 1794.245 MHz processor. > [ 11.112379] Built 1 zonelists. Total pages: 64961 > [ 11.112386] Kernel command line: > root=UUID=5ebd1580-8674-4d7e-a68d-cee0a05603e2 ro > quiet splash > [ 11.112630] mapped APIC to ffffd000 (fee00000) > [ 11.112634] mapped IOAPIC to ffffc000 (fec00000) > [ 11.112639] Enabling fast FPU save and restore... > done. > [ 11.112644] Enabling unmasked SIMD FPU exception > support... done. > [ 11.112661] Initializing CPU#0 > [ 11.112764] PID hash table entries: 1024 (order: > 10, 4096 bytes) > [ 11.114404] Console: colour VGA+ 80x25 > [ 11.114651] Dentry cache hash table entries: 32768 > (order: 5, 131072 bytes) > [ 11.114875] Inode-cache hash table entries: 16384 > (order: 4, 65536 bytes) > [ 11.123851] Memory: 248632k/261888k available > (1993k kernel code, 12736k reserved, 900k data, 328k > init, 0k highmem) > [ 11.123866] virtual kernel memory layout: > [ 11.123868] fixmap : 0xfff4e000 - 0xfffff000 > ( 708 kB) > [ 11.123870] pkmap : 0xff800000 - 0xffc00000 > (4096 kB) > [ 11.123871] vmalloc : 0xd0800000 - 0xff7fe000 > ( 751 MB) > [ 11.123873] lowmem : 0xc0000000 - 0xcffc0000 > ( 255 MB) > [ 11.123874] .init : 0xc03d9000 - 0xc042b000 > ( 328 kB) > [ 11.123876] .data : 0xc02f2429 - 0xc03d36d4 > ( 900 kB) > [ 11.123877] .text : 0xc0100000 - 0xc02f2429 > (1993 kB) > [ 11.123882] Checking if this processor honours the > WP bit even in supervisor mode... Ok. > [ 11.200663] Calibrating delay using timer specific > routine.. 3599.85 BogoMIPS (lpj=7199703) > [ 11.200728] Security Framework v1.0.0 initialized > [ 11.200739] SELinux: Disabled at boot. > [ 11.200765] Mount-cache hash table entries: 512 > [ 11.200989] CPU: After generic identify, caps: > 3febfbff 00000000 00000000 00000000 00000000 00000000 > 00000000 > [ 11.201008] CPU: Trace cache: 12K uops, L1 D cache: > 8K > [ 11.201012] CPU: L2 cache: 512K > [ 11.201015] CPU: Hyper-Threading is disabled > [ 11.201019] CPU: After all inits, caps: 3febfbff > 00000000 00000000 00003080 00000000 00000000 00000000 > [ 11.201036] Compat vDSO mapped to ffffe000. > [ 11.201041] Remapping vsyscall page to ffffe000 > [ 11.201059] Checking 'hlt' instruction... OK. > [ 11.216838] SMP alternatives: switching to UP code > [ 11.217150] Freeing SMP alternatives: 11k freed > [ 11.217485] Early unpacking initramfs... done > [ 11.673782] ACPI: Core revision 20060707 > [ 11.674079] ACPI: Looking for DSDT in initramfs... > file /DSDT.aml not found, using machine DSDT. > [ 11.677451] CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz > stepping 04 > [ 11.677509] Total of 1 processors activated > (3599.85 BogoMIPS). > [ 11.677660] ENABLING IO-APIC IRQs > [ 11.677867] ..TIMER: vector=0x31 apic1=0 pin1=2 > apic2=-1 pin2=-1 > [ 11.823955] Brought up 1 CPUs > [ 11.824329] Booting paravirtualized kernel on bare > hardware > [ 11.824431] Time: 1:22:30 Date: 10/09/107 > [ 11.824476] NET: Registered protocol family 16 > [ 11.824617] EISA bus registered > [ 11.824625] ACPI: bus type pci registered > [ 11.824775] PCI: PCI BIOS revision 2.10 entry at > 0xfda95, last bus=2 > [ 11.824778] PCI: Using configuration type 1 > [ 11.824781] Setting up standard PCI resources > [ 11.832268] ACPI: Interpreter enabled > [ 11.832274] ACPI: Using IOAPIC for interrupt > routing > [ 11.832965] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 11.832978] PCI: Probing PCI hardware (bus 00) > [ 11.833483] PCI quirk: region 0400-047f claimed by > ICH4 ACPI/GPIO/TCO > [ 11.833489] PCI quirk: region 0500-053f claimed by > ICH4 GPIO > [ 11.833911] Boot video device is 0000:01:00.0 > [ 11.834047] PCI: Firmware left 0000:02:08.0 e100 > interrupts enabled, disabling > [ 11.834204] PCI: Transparent bridge - 0000:00:1e.0 > [ 11.834239] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0._PRT] > [ 11.843260] ACPI: PCI Interrupt Routing Table > [\_SB_.PCI0.PCI1._PRT] > [ 11.846163] ACPI: Power Resource [FDDP] (off) > [ 11.846773] ACPI: Power Resource [URP1] (off) > [ 11.847481] ACPI: Power Resource [URP2] (off) > [ 11.848310] ACPI: Power Resource [LPTP] (off) > [ 11.850264] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 > 4 5 6 7 9 10 *11 12 14 15) > [ 11.850588] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 > 4 5 6 7 *9 10 11 12 14 15) > [ 11.850907] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 > 4 5 6 7 9 10 11 12 14 15) *0, disabled. > [ 11.851230] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 > 4 5 6 7 9 10 *11 12 14 15) > [ 11.851559] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 > 4 5 6 7 9 10 *11 12 14 15) > [ 11.851896] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 > 4 5 6 7 9 10 11 12 14 15) *0, disabled. > [ 11.852221] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 > 4 5 6 7 9 10 *11 12 14 15) > [ 11.852544] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 > 4 5 6 7 9 *10 11 12 14 15) > [ 11.852723] Linux Plug and Play Support v0.97 (c) > Adam Belay > [ 11.852742] pnp: PnP ACPI init > [ 11.857371] pnp: PnP ACPI: found 13 devices > [ 11.857380] PnPBIOS: Disabled by ACPI PNP > [ 11.857458] PCI: Using ACPI for IRQ routing > [ 11.857463] PCI: If a device doesn't work, try > "pci=routeirq". If it helps, post a report > [ 11.861383] NET: Registered protocol family 8 > [ 11.861386] NET: Registered protocol family 20 > [ 11.862186] PCI: Bridge: 0000:00:01.0 > [ 11.862191] IO window: c000-cfff > [ 11.862198] MEM window: ff800000-ff8fffff > [ 11.862203] PREFETCH window: ec900000-f49fffff > [ 11.862209] PCI: Bridge: 0000:00:1e.0 > [ 11.862214] IO window: d000-dfff > [ 11.862221] MEM window: ff900000-ff9fffff > [ 11.862227] PREFETCH window: f4a00000-f6afffff > [ 11.862251] PCI: Setting latency timer of device > 0000:00:1e.0 to 64 > [ 11.862293] NET: Registered protocol family 2 > [ 11.887938] IP route cache hash table entries: 2048 > (order: 1, 8192 bytes) > [ 11.888057] TCP established hash table entries: > 8192 (order: 4, 65536 bytes) > [ 11.888118] TCP bind hash table entries: 4096 > (order: 3, 32768 bytes) > [ 11.888149] TCP: Hash tables configured > (established 8192 bind 4096) > [ 11.888154] TCP reno registered > [ 11.899988] checking if image is initramfs... it is > [ 12.796772] Freeing initrd memory: 6784k freed > [ 12.797414] audit: initializing netlink socket > (disabled) > [ 12.797435] audit(1194571351.768:1): initialized > [ 12.797639] VFS: Disk quotas dquot_6.5.1 > [ 12.798149] Dquot-cache hash table entries: 1024 > (order 0, 4096 bytes) > [ 12.798224] io scheduler noop registered > [ 12.798228] io scheduler anticipatory registered > [ 12.798232] io scheduler deadline registered > [ 12.798246] io scheduler cfq registered (default) > [ 12.798607] isapnp: Scanning for PnP cards... > [ 13.154524] isapnp: No Plug & Play device found > [ 13.193661] Real Time Clock Driver v1.12ac > [ 13.193740] Serial: 8250/16550 driver $Revision: > 1.90 $ 4 ports, IRQ sharing enabled > [ 13.193887] serial8250: ttyS0 at I/O 0x3f8 (irq = > 4) is a 16550A > [ 13.194125] serial8250: ttyS1 at I/O 0x2f8 (irq = > 3) is a 16550A > [ 13.195142] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is > a 16550A > [ 13.195533] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is > a 16550A > [ 13.195827] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > GSI 22 (level, low) -> IRQ 16 > [ 13.195840] ACPI: PCI interrupt for device > 0000:02:0a.0 disabled > [ 13.195948] mice: PS/2 mouse device common for all > mice > [ 13.196840] RAMDISK driver initialized: 16 RAM > disks of 65536K size 1024 blocksize > [ 13.197230] input: Macintosh mouse button emulation > as /class/input/input0 > [ 13.197286] Uniform Multi-Platform E-IDE driver > Revision: 7.00alpha2 > [ 13.197292] ide: Assuming 33MHz system bus speed > for PIO modes; override with idebus=xx > [ 13.197603] PNP: PS/2 Controller > [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 > [ 13.201551] serio: i8042 KBD port at 0x60,0x64 irq > 1 > [ 13.201563] serio: i8042 AUX port at 0x60,0x64 irq > 12 > [ 13.201809] EISA: Probing bus 0 at eisa.0 > [ 13.201853] EISA: Detected 0 cards. > [ 13.231961] TCP cubic registered > [ 13.231971] NET: Registered protocol family 1 > [ 13.232006] Using IPI No-Shortcut mode > [ 13.232574] ACPI: (supports S0 S1 S4 S5) > [ 13.232640] Magic number: 15:630:356 > [ 13.233367] Freeing unused kernel memory: 328k > freed > [ 13.234160] Time: tsc clocksource has been > installed. > [ 13.249220] input: AT Translated Set 2 keyboard as > /class/input/input1 > [ 14.558847] Capability LSM initialized > [ 14.619625] ACPI Exception (acpi_processor-0677): > AE_NOT_FOUND, Processor Device is not present > [20060707] > [ 15.424471] SCSI subsystem initialized > [ 15.433582] libata version 2.20 loaded. > [ 15.439560] ata_piix 0000:00:1f.1: version 2.10ac1 > [ 15.439600] PCI: Setting latency timer of device > 0000:00:1f.1 to 64 > [ 15.439675] ata1: PATA max UDMA/100 cmd 0x000101f0 > ctl 0x000103f6 bmdma 0x0001ffa0 irq 14 > [ 15.439727] ata2: PATA max UDMA/100 cmd 0x00010170 > ctl 0x00010376 bmdma 0x0001ffa8 irq 15 > [ 15.439751] scsi0 : ata_piix > [ 15.453349] usbcore: registered new interface > driver usbfs > [ 15.453384] usbcore: registered new interface > driver hub > [ 15.453421] usbcore: registered new device driver > usb > [ 15.533000] USB Universal Host Controller Interface > driver v3.0 > [ 15.569977] e100: Intel(R) PRO/100 Network Driver, > 3.5.17-k2-NAPI > [ 15.569983] e100: Copyright(c) 1999-2006 Intel > Corporation > [ 15.611662] ata1.00: ata_hpa_resize 1: sectors = > 39102336, hpa_sectors = 39102336 > [ 15.611669] ata1.00: ATA-6: ST320410A, 3.39, max > UDMA/100 > [ 15.611673] ata1.00: 39102336 sectors, multi 16: > LBA > [ 15.623668] ata1.00: ata_hpa_resize 1: sectors = > 39102336, hpa_sectors = 39102336 > [ 15.623676] ata1.00: configured for UDMA/100 > [ 15.623695] scsi1 : ata_piix > [ 15.664027] Floppy drive(s): fd0 is 1.44M > [ 15.733289] FDC 0 is a post-1991 82077 > [ 15.954967] ata2.00: ATAPI, max UDMA/33 > [ 16.126751] ata2.00: configured for UDMA/33 > [ 16.126943] scsi 0:0:0:0: Direct-Access ATA > ST320410A 3.39 PQ: 0 ANSI: 5 > [ 16.131650] scsi 1:0:0:0: CD-ROM MITSUMI > CR-48XATE 1.0E PQ: 0 ANSI: 5 > [ 16.133753] ACPI: PCI Interrupt 0000:00:1f.2[D] -> > GSI 19 (level, low) -> IRQ 17 > [ 16.133772] PCI: Setting latency timer of device > 0000:00:1f.2 to 64 > [ 16.133779] uhci_hcd 0000:00:1f.2: UHCI Host > Controller > [ 16.133975] uhci_hcd 0000:00:1f.2: new USB bus > registered, assigned bus number 1 > [ 16.134009] uhci_hcd 0000:00:1f.2: irq 17, io base > 0x0000ef40 > [ 16.134172] usb usb1: configuration #1 chosen from > 1 choice > [ 16.134219] hub 1-0:1.0: USB hub found > [ 16.134229] hub 1-0:1.0: 2 ports detected > [ 16.153658] SCSI device sda: 39102336 512-byte hdwr > sectors (20020 MB) > [ 16.153681] sda: Write Protect is off > [ 16.153684] sda: Mode Sense: 00 3a 00 00 > [ 16.153712] SCSI device sda: write cache: enabled, > read cache: enabled, doesn't support DPO or FUA > [ 16.153802] SCSI device sda: 39102336 512-byte hdwr > sectors (20020 MB) > [ 16.153818] sda: Write Protect is off > [ 16.153821] sda: Mode Sense: 00 3a 00 00 > [ 16.153848] SCSI device sda: write cache: enabled, > read cache: enabled, doesn't support DPO or FUA > [ 16.153853] sda: sda1 sda2 < sda5 > > [ 16.209658] sd 0:0:0:0: Attached scsi disk sda > [ 16.217377] sd 0:0:0:0: Attached scsi generic sg0 > type 0 > [ 16.217567] sr 1:0:0:0: Attached scsi generic sg1 > type 5 > [ 16.238589] ACPI: PCI Interrupt 0000:00:1f.4[C] -> > GSI 23 (level, low) -> IRQ 18 > [ 16.238610] PCI: Setting latency timer of device > 0000:00:1f.4 to 64 > [ 16.238616] uhci_hcd 0000:00:1f.4: UHCI Host > Controller > [ 16.238651] uhci_hcd 0000:00:1f.4: new USB bus > registered, assigned bus number 2 > [ 16.238686] uhci_hcd 0000:00:1f.4: irq 18, io base > 0x0000ef80 > [ 16.238817] usb usb2: configuration #1 chosen from > 1 choice > [ 16.238860] hub 2-0:1.0: USB hub found > [ 16.238871] hub 2-0:1.0: 2 ports detected > [ 16.248537] sr0: scsi3-mmc drive: 40x/40x writer > cd/rw xa/form2 cdda tray > [ 16.248546] Uniform CD-ROM driver Revision: 3.20 > [ 16.248870] sr 1:0:0:0: Attached scsi CD-ROM sr0 > [ 16.346614] ACPI: PCI Interrupt 0000:02:08.0[A] -> > GSI 20 (level, low) -> IRQ 19 > [ 16.370062] e100: eth0: e100_probe: addr > 0xff9ff000, irq 19, MAC addr 00:03:47:28:A5:C3 > [ 16.482088] usb 1-1: new full speed USB device > using uhci_hcd and address 2 > [ 16.658420] usb 1-1: configuration #1 chosen from 1 > choice > [ 16.716007] Attempting manual resume > [ 16.716013] swsusp: Resume From Partition 8:5 > [ 16.716016] PM: Checking swsusp image. > [ 16.716289] PM: Resume from disk failed. > [ 16.784804] kjournald starting. Commit interval 5 > seconds > [ 16.784822] EXT3-fs: mounted filesystem with > ordered data mode. > [ 16.905556] usb 2-2: new full speed USB device > using uhci_hcd and address 2 > [ 17.067646] usb 2-2: configuration #1 chosen from 1 > choice > [ 17.070563] hub 2-2:1.0: USB hub found > [ 17.073514] hub 2-2:1.0: 4 ports detected > [ 30.192991] e100: eth0: e100_watchdog: link up, > 100Mbps, full-duplex > [ 31.502450] NET: Registered protocol family 17 > [ 32.257412] pci_hotplug: PCI Hot Plug PCI Core > version: 0.5 > [ 32.260261] shpchp: Standard Hot Plug PCI > Controller Driver version: 0.4 > [ 32.661680] intel_rng: Firmware space is locked > read-only. If you can't or > [ 32.661683] intel_rng: don't want to disable this > in firmware setup, and if > [ 32.661686] intel_rng: you are certain that your > system has a functional > [ 32.661688] intel_rng: RNG, try using the > 'no_fwh_detect' option. > [ 32.712142] iTCO_vendor_support: vendor-support=0 > [ 32.713818] iTCO_wdt: Intel TCO WatchDog Timer > Driver v1.01 (11-Nov-2006) > [ 32.713944] iTCO_wdt: failed to reset NO_REBOOT > flag, reboot disabled by hardware > [ 32.713954] iTCO_wdt: No card detected > [ 32.867408] Linux agpgart interface v0.102 (c) Dave > Jones > [ 32.894939] agpgart: Detected an Intel i845 > Chipset. > [ 32.898986] agpgart: AGP aperture is 64M @ > 0xf8000000 > [ 33.474002] input: PC Speaker as > /class/input/input2 > [ 33.564720] parport: PnPBIOS parport detected. > [ 33.564750] parport0: PC-style at 0x378, irq 7 > [PCSPP,TRISTATE,EPP] > [ 33.606715] drivers/usb/class/usblp.c: usblp0: USB > Bidirectional printer dev 2 if 0 alt 0 proto 2 vid > 0x03F0 pid 0x2B17 > [ 33.606739] usbcore: registered new interface > driver usblp > [ 33.606744] drivers/usb/class/usblp.c: v0.13: USB > Printer Device Class driver > [ 33.640912] slamr: module license 'Smart Link Ltd.' > taints kernel. > [ 33.649995] slamr: SmartLink AMRMO modem. > [ 33.651044] slamr: probe 2000:2800 SL2800 card... > [ 33.651060] ACPI: PCI Interrupt 0000:02:0a.0[A] -> > GSI 22 (level, low) -> IRQ 16 > [ 33.652166] slamr: slamr0 is SL2800 card. > [ 34.225856] ACPI: PCI Interrupt 0000:00:1f.5[B] -> > GSI 17 (level, low) -> IRQ 20 > [ 34.225889] PCI: Setting latency timer of device > 0000:00:1f.5 to 64 > [ 34.313167] input: ImPS/2 Generic Wheel Mouse as > /class/input/input3 > [ 34.543409] intel8x0_measure_ac97_clock: measured > 56188 usecs > [ 34.543416] intel8x0: clocking to 41150 > [ 34.774273] fuse init (API version 7.8) > [ 34.812883] lp0: using parport0 (interrupt-driven). > [ 34.859911] Adding 746980k swap on > /dev/disk/by-uuid/58976d14-595e-43b0-b535-682b8cd84892. > Priority:-1 extents:1 across:746980k > [ 35.022860] EXT3 FS on sda1, internal journal > [ 35.259953] NET: Registered protocol family 10 > [ 35.260103] lo: Disabled Privacy Extensions > [ 41.245435] input: Power Button (FF) as > /class/input/input4 > [ 41.251890] ACPI: Power Button (FF) [PWRF] > [ 41.303118] input: Power Button (CM) as > /class/input/input5 > [ 41.309546] ACPI: Power Button (CM) [PBTN] > [ 41.366640] Using specific hotkey driver > [ 41.650646] ibm_acpi: ec object not found > [ 41.693739] No dock devices found. > [ 41.770142] pcc_acpi: loading... > [ 46.216753] eth0: no IPv6 routers present > [ 49.218015] ppdev: user-space parallel port driver > [ 49.416346] [drm] Initialized drm 1.1.0 20060810 > [ 49.544415] ACPI: PCI Interrupt 0000:01:00.0[A] -> > GSI 16 (level, low) -> IRQ 21 > [ 49.548516] [drm] Initialized r128 2.5.0 20030725 > on minor 0 > [ 49.549664] agpgart: Found an AGP 2.0 compliant > device at 0000:00:00.0. > [ 49.550012] agpgart: Putting AGP V2 device at > 0000:00:00.0 into 1x mode > [ 49.550286] agpgart: Putting AGP V2 device at > 0000:01:00.0 into 1x mode > [ 50.695948] apm: BIOS not found. > [ 51.140918] Bluetooth: Core ver 2.11 > [ 51.141010] NET: Registered protocol family 31 > [ 51.141013] Bluetooth: HCI device and connection > manager initialized > [ 51.141018] Bluetooth: HCI socket layer initialized > [ 51.192002] Bluetooth: L2CAP ver 2.8 > [ 51.192009] Bluetooth: L2CAP socket layer > initialized > [ 51.274856] Bluetooth: RFCOMM socket layer > initialized > [ 51.274876] Bluetooth: RFCOMM TTY layer initialized > [ 51.274879] Bluetooth: RFCOMM ver 1.8 > [ 62.160749] eth0: no IPv6 routers present > > > Bob Terrell > Lubbock, Texas > bob_terrell_texas@xxxxxxxxx > > > > __________________________________________________ > Do You Yahoo!? > Tired of spam? Yahoo! Mail has the best spam protection around > http://mail.yahoo.com >
